Wi-Fi Operation Manual
Table Of Contents
- INTRODUCTION
- IMPORTANT SAFETY INFORMATION
- PERSONAL INJURY OR DEATH HAZARDS
- FCC Caution
- Kuhl, Kuhl Q, And Wallmaster Controls
- KUHL, KUHL Q, AND WALLMASTER
- Wi-Fi SET UP INSTRUCTIONS
- Wi-Fi TROUBLESHOOTING TIPS
- FA Pro/ FA Premier App Info
- FA Pro, FA Premier Troubleshooting
- Chill Premier/ Unifit App Info
- Chill Premier/ Unifit Registration
- Chill Premier/ Unifit Login
- Chill Premier/ Unifit Troubleshooting
32 PB
5.
Note: If at any time you need to start over- Pressing "Display" on the remote control 6 times will
reset the wireless setup configuration on the AC unit back to CF mode. Pressing the Display
button an additional 6 times after CF mode appears will switch the unit to AP mode. Please allow
the unit 10-15 seconds to switch modes if toggling from CF to AP modes.
You can "Rename" the AC unit as you like, share with family, or press "Done" to start to
controlling the device.
""
6
View help
How to reset device?
Press the DISPLAY on the remote control key 6
times in the time of 6 seconds until the LCD
screen show CF , indicating connect mode""
Press the DISPLAY on the remote control key 6
times in the time of 6 seconds until the LCD
screen show AP , indicating hotspot mode""
ADD THE AC UNIT TO THE WIRELESS NETWORK USING AP MODE""
If connections to the wireless network fail using the CF mode , you can connect using
the AP mode (using the AC unit as a mobile hotspot)
""
""
1.On the App page indicating CF mode, click AP mode in the top, right-hand corner as illustrated.
2.
AP should show on the page as illustrated below. Press "Next Step" to continue.
""
FRIEDRICH GO
Chill Premier/ Unit
5.
Note: If at any time you need to start over- Pressing "Display" on the remote control 6 times will
reset the wireless setup configuration on the AC unit back to CF mode. Pressing the Display
button an additional 6 times after CF mode appears will switch the unit to AP mode. Please allow
the unit 10-15 seconds to switch modes if toggling from CF to AP modes.
You can "Rename" the AC unit as you like, share with family, or press "Done" to start to
controlling the device.
""
6
View help
How to reset device?
Press the DISPLAY on the remote control key 6
times in the time of 6 seconds until the LCD
screen show CF , indicating connect mode""
Press the DISPLAY on the remote control key 6
times in the time of 6 seconds until the LCD
screen show AP , indicating hotspot mode""
ADD THE AC UNIT TO THE WIRELESS NETWORK USING AP MODE""
If connections to the wireless network fail using the CF mode , you can connect using
the AP mode (using the AC unit as a mobile hotspot)
""
""
1.On the App page indicating CF mode, click AP mode in the top, right-hand corner as illustrated.
2.
AP should show on the page as illustrated below. Press "Next Step" to continue.
""
5. Note: If at any time you need to start over- Pressing “Display” on the remote control 6 times will reset the wire-
less setup configuration on the AC unit back to CF mode. Pressing the Display button an additional 6 times after
CF mode appears will switch the unit to AP mode. Please allow the unit 10-15 seconds to switch modes if toggling
from CF to AP modes.
You can “Rename” the AC unit as you like, share with family, or press “Done” to start to controlling the device.
ADD THE AC UNIT TO THE WIRELESS NETWORK USING “AP MODE”
If connections to the wireless network fail using the “CF“ mode , you can connect using the “AP“ mode (using
the AC unit as a mobile hotspot)
1. On the App page indicating CF mode, click AP mode in the top, right-hand corner as illustrated.
2. AP should show on the page as illustrated below. Press “Next Step” to continue.