Installation Guide

INSTALLATION OVERVIEW
IMPOR
TANT NOTES:
• Make sure the screws for the blower motor and
blower plate are securely tightened when they
are reinstalled. This
will help to prevent
excessive vibration.
• Make sure the motor wiring has been properly
routed and secured, and that the wires are not
pinched.
I
nstallation Instructions
Place the mounting plate against the wall and
i
nsert the toggle wings into the holes in the
wall to mount the plate.
Tighten all bolts
. Pull the plate away from the
wall to help tighten the bolts.
4
3
ATTACH THE MOUNTING
PLATE TO THE WALL
Att
ach the plate to the wall using toggle bolts.
At least one wood screw must be used to
attach the plate to a wall stud.
Remove the toggle wings from the bolts.
Insert the bolts into the mounting plate through the
holes designated to go into drywall and reattach the
toggle wings to
3
⁄4" (19 mm) onto each bolt.
1
W
all
Moun
tin
g
P
l
ate
Spacing for Toggles
More T
han Wall
Thickness
Bolt End
T
o
ggle
Bolt
T
o
ggle Wings
To use toggle bolts:
2
RECIRCULATING (Non-Vented Ductless)
NOTE:
If the cabinet depth including the cabinet doors
NOTE: Before
tightening toggle bolts and wood
screw, make sure the bottom of the mounting
plate touch the bottom of the cabinet when
pushed flush against the wall and that the plate is
properly centered under the cabinet.
CAUTION: Be careful to avoid pinching fingers
between the back of the mounting plate and the
wall.
A
A1
.
At
tach Mounting Plate to Wall
Pr
epare T
o
p Cabinet
Check Blower Plate
Mount the Microwave Oven
Install or change Charcoal Filter
A2.
A3.
A4.
A5.
A1.
Cabinet
Cabinet
(33 cm)
13" MAX.
is more than 13" then the unit must be spaced
out
from wall using adequate materials supporting
150 Ibs to allow proper top vent air exhaust/intake.
3/8"
TO
EDG
E
NO
TE
: IT IS
VERY
I
M
POR
TANT TO
READ AND FO
LLO
W
T
HE
D
IRECTIO
NS
IN THE INSTALLA
T
ION INSTRUCTI
ONS
BE
F
O
RE PR
O
CEEDINGWITH
T
H
IS
REAR W
A
LL TEMPLAT
E.
T
hi
s
Rear
Wa
ll T
e
mpl
a
te
ser
ve
s
to p
os
itio
n
th
e
b
o
tto
m
mou
ntin
g p
lateand to l
o
cate th
e h
or
i
z
on
ta
l
ex
h
au
st
ou
t
le
t.
1
. Us
e a l
e
vel
to
c
heck
th
at th
e t
emplate
is p
os
ition
ed
accu
ratel
y
.
2. L
oca
te a
nd
m
ar
k at le
a
s
t o
nestu
d
on
th
e
le
ft o
r
r
igh
t
s
id
e
o
f the
c
e
n
terli
ne
.
Itis im
po
rt
an
t to u
se a
t le
as
t
one
wo
od
scre
w
mo
u
nte
d
fi
r
mly
i
n a
s
tud
to suppor
t th
e weigh
t
of
th
e mic
r
ow
ave
.
M
ar
k
tw
o ad
di
tion
a
l, e
venly
spa
c
ed
lo
c
atio
n
s f
or
th
e
s
upplied
to
ggle
bo
lts.
3. Dr
i
ll
h
ol
e
s in
th
e
m
ar
ked lo
cation
s.Whe
r
e t
he
r
e is
a
s
tu
d
, d
r
ill
a 3/16" h
ole
for
woo
d screws.
F
or h
oles
th
atdo
not lin
e upw
ith
a
s
tu
d, dr
il
l 5
/8
"
h
o
le
s fo
r
to
gg
l
e bo
lts.
DO
NOT
I
NSTAL
L T
HE
MO
U
NT
I
NG
PLA
T
E
A
T
T
HIS
T
IME.
4. Re
m
ove th
e te
mpla
te fr
om
the r
ea
r
wal
l.
5.
Re
vie
ht
w
e In
sta
llation
Instr
uc
ti
on b
oo
k for
y
our
in
sta
lla
tion
s
i
tua
tion.
Locat
e and m
ark
holes
to ali
gn wi
th holes in t
he
mounting
p
late.
IMPO
RTANT
:
LO
C
AT
E
AT LEAST
O
N
E
STUD
O
N EI
T
HER
SID
E
O
F
TH
E
CENTER
LIN
E
.
MAR
KT
HE LO
CATIO
N
FO
R 2 ADDIT
IO
NA
L, EV
ENLY
SP
ACE
D T
OG
GLE
BO
LTS
IN
THE MO
UNTING
PLATE
AREA
.
Locate and mar
k
hol
es
to al
i
gn with holes
in t
he
.
e
ta
lp
gn
itn
u
o
m
IMPO
RTANT
:
LOCAT
E AT LEAST ON
ESTUD
O
N EI
T
HER SI
D
E O
F
TH
E
CENT
ER
LI
N
E.
MARK
T
HE LO
CATIONFO
R 2 ADDITION
A
L, EV
ENLY
SP
ACED
TO
G
GLE BO
LTS IN
THE MO
UN
TING
PLATE
AREA
.
Trim t
he r
ear wal
l temp
lat
e along
t
he do
tted
line.
Trim the rear
wal
l t
em
pla
t
e along
th
e dotted lin
e.
12"
4"
Darlevu
e
lt
aa la
ho
j
a
pa
ra
c
o
nsul
t
a
r
la
v
e
r
s
i
ó
ne
nEs
pa
ño
l.
EN-10