Installation Guide
•
•
Remove and save the screw that holds the
blower plate to the microwave. Lift off the
blowe
r plate.
Back of
Microwave
Installation Instructions
PREPARING THE REAR WALL
FOR OUTSIDE BACK EXHAUST
B1.
You need to cut an opening in the rear
wa
ll for outside exhaust.
• Read
the instructions on the REAR
WALL TEMPLATE.
• Tape it to the rear wall.
• Cut the opening, following the instructions
of the REAR WALL TEMPLATE.
B2.
OUTSIDE B
ACK EXHAUST (Horizontal Duct)
B
Blower Plate
REMOVE BLOWER PLATE
INSTALLATION OVERVIEW
B1. Prepare Rear Wall
B2. Remove Blower Plate
B3. Attach Mounting Plate to Wall
B4. Prepare Top Cabinet
B5. Adjust Blower
B6. Mount the Microwave Oven
IMPORTANT
NOTES:
3/8" TO EDGE
NOTE: IT IS VE
RY IMPORTANT TO
READ AND FOLLOW THE DIRECTIONS
IN THE INSTALLATION INSTRUCTIONS
BEFORE PROCEEDING WITH THIS
REAR WALL TEMPLATE.
This Rear Wall Template serves to position the bottom
mounting plate and to locate the horizontal exhaust
outlet.
1. Use a level to check that the template is positioned
accurately.
2. Locate and mark at least one stud on the left or
right side of the centerline.
It is important to use at least one wood
screw mounted firmly in a stud to support the weight
of the microwave. Mark two additional, evenly spaced
locations for the supplied toggle bolts.
3. Drill holes in the marked locations. Where there is
a stud, drill a 3/16" hole for wood screws. For holes
that do not line up with a stud, drill 5/8" holes for
toggle bolts.
DO NOT INSTALL THE MOUNTING PLATE
AT THIS TIME.
4. Remove the template from the rear wall.
5. Review the Installation Instruction book for your
installation situation.
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
LOCATE
AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR
2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
Locate and mark holes to align with holes in the
mounting plate.
IMPORTA
NT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
Trim the rear wall template along the dotted line.
Trim the rear wall template along the dotted line.
12"
4"
Darle vuelta a la hoja para consultar la
versión en Español.
Make sure the screws for the
blower
motor and blower plate
are securely tightened when
they are reinstalled. This will help
to prevent excessive vibration.
Make sure the motor wiring has
been properly routed and
secured, and that the wires are
not pinched.
3
/8"
TO
EDGE
NO
TE
: IT IS
VERY I
M
PO
R
TANT TO
READ AND FO
LLO
WT
HED
IRECTIONS
IN THE INSTALLAT
ION INSTRU
CTI
ONS
BE
FORE PR
O
CEEDINGWITH T
HIS
REAR WA
LL TEMPLA
T
E
.
This
R
ea
r
Wall T
e
mpl
a
te
s
e
rves
to p
ositio
n
th
e
b
o
tto
m
mou
ntin
g p
latea
n
d
to l
o
c
ate th
e h
o
ri
z
on
ta
l
ex
h
au
st
ou
tle
t.
1
. Use a l
evel
to
c
h
e
ck
th
at th
e t
empla
te
is p
osition
ed
a
ccur
ate
ly
.
2. L
o
ca
te a
nd
m
ar
k at le
as
t o
nestu
d
on
the
le
ft o
r
righ
t side
o
f the
c
e
n
te
rl
i
n
e.
It is im
po
rt
an
t to u
se
a
t least
one
wo
od
scre
wmo
unted
fi
r
mly i
n a s
tud
to support th
e weigh
t
o
f
th
e mic
r
ow
ave.
Mar
k tw
o a
d
di
tion
al, e
ve
nl
y
spa
c
ed
lo
c
atio
n
s f
or th
e
s
upplied
to
ggle
bo
lts.
3. Drill
h
ole
s in
th
e m
ar
ked lo
cation
s.Wher
e t
he
r
e is
a
s
tud,
d
r
ill
a 3/16" h
ol
e
for
woo
d s
cr
e
w
s.
For h
oles
that
d
o
n
ot lin
e up
w
ith a s
tu
d, d
r
il
l 5
/8
"
holes fo
r
to
ggl
e bo
lts.
DO
NO
T
I
N
S
T
A
L
L T
HE MO
U
NT
I
N
G P
L
AT
E
AT
THIS
TIME.
4. Re
m
ove th
e templa
te
fr
omthe
r
ea
r
wal
l.
5.
R
evie
htw
e In
sta
llationIns
tr
uc
tion boo
k for
you
r
in
sta
llatio
n si
tua
t
ion.
Locat
e and m
ar
k
holes
to ali
gn with holes in t
he
mounting
plate.
IMPO
RTANT
:
LO
C
ATE
AT LEA
ST
O
NE
STUD
ON EITHER
SIDE OF
TH
E CENTER
LI
N
E.
MARKT
HE LOCATIO
N
FOR 2 ADDITIONA
L, EV
ENLY
SPACED TO
GGLE
BO
LTS
IN
THE MO
UN
TING
PLATE
AREA.
Locate and mar
k hol
es
to al
ign with holes
in t
he
.
e
t
alpgnitnuom
IMPO
RTANT
:
LO
CAT
E AT LEAST ONESTUD O
N EI
T
HER SI
D
E O
F
THE
CENT
E
R
LINE.
MARKT
HE LO
CATIONF
O
R 2 ADDITION
A
L, EV
ENLY
SP
ACEDTO
G
GLE
BO
LTS IN
THE MO
UNTING
PLATE
AREA
.
Trim the r
ear wall temp
lat
e along
t
he dotted
line.
Trim the rear
wal
l t
em
pla
t
e along
t
h
e dotted line.
12"
4"
Dar
l
ev
u
elt
aa la ho
j
apar
a
co
ns
ul
t
a
r
la
v
e
r
s
i
óne
n
Es
pa
ño
l.
EN-16