Installation Guide

Place the mounting plate against the wall and
ins
ert the toggle wings into the holes in the
wall to mount the plate.
NOTE: Before tightening toggle bolts and wood
screw, make sure the bottom of the moun
ting plate
touch the bottom of the cabinet when pushed
flush against the wall and that the plate is properly
centered under the cabinet.
CAUTION: Be careful to avoid pinching fingers
between the back of the mounting plate and the
wall.
Tighten all bolts. Pull the plate away from the
wall t
o help tighten the bolts.
3
4
ATTACH THE MOUNT
ING
PLATE TO THE WALL
A
ttach the plate to the wall using toggle
bolts. At least one wood screw must be
used to attach the plate to a wall stud.
Re
move the toggle wings from the bolts.
Insert the bolts into the mounting plate
through the holes designated to go into
drywall and reattach the toggle wings to
3
⁄4″ (19 mm) onto each bolt.
1
INSTALLATION OVERVIEW
Wall
Mou
nting
Pla
te
Spacing for Toggles
M
ore Than Wall
Thickness
Bolt End
T
oggle
Bolt
Togg
le Wings
To use toggle bolts:
Installation Instructions
2
OUTSIDE TO
P EXHAUST (Vertical Duct)
• Make sure the screws for the
blower motor and blower plate are
securely tightened when
they are reinstalled. This will help to
prevent excessive vibration.
• Make s
ure the motor wiring has
been properly routed and secured,
and that the wires are not pinched.
Connect Ductwork
IMPO
RTANT NOTES:
Attach Mounting Plate to Wall
Prep
are Top Cabinet
Adapting
Microwave Blower for
Outside
Top Exhaust
Check Damper Operation
Mount Microwave Oven Adjust
Exh
aust Adaptor
C
C2.
C1.
C3.
C4.
C6.
C5.
C6.
C1.
3/
8"
TO
EDG
E
NOTE
:
IT IS
VERY IMPO
R
TANT TO
READ AND FO
LLO
WT
HE
D
IRECTIO
N
S
IN THE INSTALLAT
ION INSTRU
CTI
O
N
S
BE
FO
RE PR
O
CEEDING
WITH TH
IS
REAR W
A
LL TEM
PLA
TE.
Thi
s
R
ea
rWa
ll Templa
te se
rves to p
ositio
n
the bo
tto
m
mou
ntin
g p
l
a
te
and
to l
oc
ate the hor
iz
ontal exhau
s
t
ou
t
let.
1
. Us
e a levelto
chec
k tha
t the t
e
m
plate i
s
pos
itioned
ac
cu
r
a
tely.
2. L
oc
ate a
ndma
r
k at lea
st o
nestud on the left or
right
s
id
e of the cente
rl
i
ne
.
It is import
a
nt to u
s
e a
t le
as
t
one
wo
od
sc
rew
mounted
fi
rmly
i
n
a
stud
to supp
or
t the w
eight
of
th
e mic
r
owav
e.
M
ar
k t
wo
a
d
dition
al, ev
en
ly
s
pac
ed
lo
cations
f
o
r
the
s
uppl
ied tog
gle bol
ts.
3. Dr
i
ll
hole
s in
th
e
marked locations.
Wher
e t
h
er
e is
a s
tu
d,
dr
il
l
a 3/1
6" h
ol
e
fo
r wood sc
r
ew
s. Fo
r ho
les
th
atdo
n
ot line up
w
ith a stu
d, d
rill 5/8
" h
oles fo
r
to
ggle bolts.
DO
NOT
IN
S
T
AL
L T
HE
MO
UNTING P
LATE
AT THIS
T
IME.
4. Re
m
o
v
e
the template fr
o
m
the r
ea
r wall.
5.Rev
iewth
e Ins
ta
ll
a
tionInst
r
ucti
o
n bo
ok for
y
ou
r
instal
l
a
ti
on situation.
Locate and m
ar
k holes
to ali
gn with holes in t
he
mounting
p
late.
IMP
O
RTANT
:
LO
C
AT
E
AT LEA
ST ONE
STUD
ON EI
T
HERSID
E O
F
THE CENTE
R
LI
N
E.
MARK
THE LO
CATIONF
O
R 2 ADDIT
IO
NA
L, EV
ENLY
SPACED T
OGGLE
BO
LTS
IN
THE MO
UN
TING
PLATE
AREA
.
Locate and mark
holes
to al
i
gn with holes
in t
he
mountingplate.
IMPORTANT:
LO
C
A
TE
AT LEA
ST O
NESTUD ON EI
THER SI
D
E
O
F
THE
CENTE
R
LI
NE
.
MARKT
HE LO
CATIO
N
FOR 2 ADDITIONA
L, EV
ENLY
SPACEDTOG
GLE BO
LTS IN
THE MOUNTING
PLATE
AREA.
Trim the re
ar
wall tem
plate along
the dotted
line.
Trim the rear
wall templat
e along
t
he dotted lin
e.
12"
4"
Da
rl
e
v
ue
lt
a
ala
hoj
a
pa
r
a
co
ns
u
ltar
la
ver
sió
n
enE
s
pa
ño
l.
EN-20