Wiring Diagram
NOTICE: This service data sheet is intended for use by persons having electrical and mechanical training
and a level of knowledge of these subjects generally considered acceptable in the appliance repair trade. The
manufacturer cannot be responsible, nor assume any liability, for injury or damage of any kind arising from
the use of this data sheet.
IMPORTANT NOTE: This unit includes an EOC (electronic oven control). This board is not eld-repairable.
Verify the unit has the proper oven relay board, oven user interface board, and touch panel based on the
model number and parts catalog.
Safe Servicing Practices
To avoid the possibility of personal injury and/or property damage, it is important that safe servicing practices
be observed. The following are some, but not all, examples of safe practices.
1. Do not attempt a product repair if you have any doubts as to your ability to complete it in a safe and
satisfactory manner.
2. Before servicing or moving an appliance, remove power cord from electric outlet, trip circuit breaker to
Off, or remove fuse.
3. Never interfere with the proper installation of any safety device.
4. Use only replacement parts specied for this appliance. Substitutions may not comply with safety
standards set for home appliances.
5. Grounding: The standard color coding for safety ground wires is green or green with yellow stripes.
Ground leads are not to be used as current carrying conductors. It is extremely important that the
service technician reestablish all safety grounds prior to completion of service. Failure to do so will
create a potential hazard.
IMPORTANT
DO NOT REMOVE THIS BAG
OR DESTROY THE CONTENTS
WIRING DIAGRAMS AND SERVICE
INFORMATION ENCLOSED
REPLACE CONTENTS IN BAG
p/n 809216912 Rev D (1712)
SERVICE DATA SHEET
ELECTRIC RANGES WITH MODULAR OVEN CONTROLS
CIRCUIT
ANALYSIS
MATRIX
Elements
Door Motor
J20-10
Light
J20-6
Conv. Fan
J20-9
Door
Switch
J5-3
DLB L2
out K1
Bake
P7
Broil
K2
Conv.
J19-2
Bake X X X X X
Broil X X
Conv. Bake X X X X X
Conv. Roast X X X X X
Clean X X X
Locking X
Unlocking X
Light X
Door Open X
Door Closed X
ELECTRONIC OVEN CONTROL (EOC) FAULT CODE DESCRIPTIONS
Fault
Code
Description of Error Code Suggested Corrective Action
F01 F02
F04 F05
Touch panel failure Disconnect power, wait 30 seconds and reapply power. If fault returns upon power-up replace the touch panel.
F03 The oven user interface board is incorrectly
congured.
Replace the oven user interface board. Make sure you install the latest revision available for this model.
F10 Oven temperature runaway: the cavity tem-
perature has been detected in excess of the
maximum safe operating temperature.
1. If oven is overheating, disconnect power. Check oven temperature probe (RTD) and replace if necessary.
2. If the oven temperature probe is good and if oven continues to overheat when power is reapplied, replace the oven relay board.
F11 Stuck key: a key has been detected has
pressed continuously for 30 seconds or
more.
1. If a key was pressed inadvertently for a long time this error code will be displayed. Make sure there is nothing (water, utensils) in contact with the
keyboard. The fault code should go away once the key is released and the Stop key is pressed. If the F011 error comes back when a key is pressed it
means the error condition is still there. If the F011 error does not come back it means the error condition is gone and the oven can be used.
2. If the fault code cannot be cleared, test the wiring harness between oven user interface board (connector I2C1 or I2C2) and touch panel (connector
I2C1 or I2C2).
3. If the fault code cannot be cleared and the wiring is good, the touch panel is most likely defective: replace the touch panel.
4. If changing the touch panel did not x the problem replace the oven user interface board.
F12 Keyboard conguration alarm: the oven
user interface board received from the touch
panel a key code that does not match the
key map.
1. Replace the oven user interface board.
2. If the problem persists replace the touch panel.
F13 Data written to non-volatile memory has
failed verication
Disconnect power, wait 30 seconds and reapply power. If fault returns upon power-up replace the oven user interface.
F15 Keyboard error Disconnect power, wait 30 seconds and reapply power. If fault returns upon power-up replace the touch panel.
F16 The oven user interface board cannot read
the potentiometers.
1. Verify that potentiometers are in OFF position correctly, disconnect power to the unit, wait 30 seconds, then reapply power.
2. If fault returns, verify harness going to the POTS connector of the user interface board to both potentiometer components.
3. If fault persists, replace potentiometers.
4. If fault persists, replace user interface board.
F17 The oven user interface board is unable to
congure the touch panel.
1. Disconnect power to the unit, wait 30 seconds, then reapply power.
2. If fault returns, verify harness going to I2C1 or I2C2 connector of the touch panel.
3. If fault persists, replace the oven user interface.
4. If fault persists, replace the touch panel.
F18 Oven relay board failure (wiggler) Replace the oven relay board.
F19 The oven user interface board is unable to
congure the oven relay board
1. Disconnect power to the unit, wait 30 seconds, then reapply power.
2. If fault returns, verify connection between the oven user interface board (MACS1 or MACS2 connector) and the oven relay board (connector J3 or
J4).
3. If fault persists, replace oven user interface board.
4. If fault persists, replace the relay board.
F22 Communication failure between the oven
user interface board and the oven relay
board
1. Disconnect power, wait 30 seconds and reapply power. Check if error condition is still there.
2. Test wiring harness between oven user interface board (connector MACS1 or MACS2) and oven relay board (connector J3 or J4).
3. If wiring harness is good replace oven relay board.
4. If the problem persists replace the oven user interface.
F23 Communication failure between the oven
user interface board and the glass touch
panel
1. Disconnect power, wait 30 seconds and reapply power. Check if error condition is still there.
2. Test wiring harness between oven user interface board (connector I2C1 or I2C2) and touch panel (connector I2C1 or I2C2).
3. If wiring harness is good replace touch panel.
4. If the problem persists replace the oven user interface.
F25
F27
The communication between the over user
interface and the oven relay board cannot
be initiated.
1. Disconnect power to the unit, wait 30 seconds, then reapply power.
2. If fault returns, verify connection between the oven user interface board (MACS1 or MACS2 connector) and the oven relay board (connector J3 or
J4).
3. If fault persists, replace relay board.
4. If fault persists, replace the oven user interface board.
F28
F29
The communication between the over user
interface and the touch panel cannot be
initiated.
1. Disconnect power to the unit, wait 30 seconds, then reapply power.
2. If fault returns, verify touch panel is connected (verify harness going to I2C1 or I2C2 connector) and is getting power from the oven user interface.
3. If fault persists, replace the touch panel.
4. If fault persists, replace the oven user interface.
F30 Open oven temperature sensor (RTD) 1. Check probe circuit wiring for possible open or short condition.
2. Verify RTD resistance at room temperature (compare to probe resistance chart). If resistance does not match the chart, replace the RTD probe.
3. If the problem persists replace the oven relay board.
F31 Shorted oven temperature probe (RTD)
F33 Meat probe temperature sensor shorted or
too hot
1. The error is triggered if the meat probe sees a temperature in excess of 392°F. Make sure the meat probe was not used in such way that it could
have seen such temperature. If the tip of the probe is not inserted in the meat it will see the cavity temperature, which can be higher than 392°F
(depending on the setpoint) and trigger the alarm.
2. When the meat probe is connected to the socket inside the oven cavity, if the meat probe is not fully inserted into the socket it may short the contacts
and cause the error. Make sure the probe is inserted as much as it can.
3. Verify meat probe resistance at room temperature. Compare to meat probe resistance chart. If the meat probe does not match the chart, replace it.
4. If the above steps failed to correct the problem, replace the oven relay board.
F50 A/D Out of Range: the oven relay board is
unable to read the status of the switches
(door, MDL)
Replace the oven relay board.
F90 Motor Door Lock mechanism failure. The
oven control does not see the Motor Door
Lock running.
1. Disconnect power to the unit, wait 30 seconds, then reapply power. Try again to make the door lock or unlock (ex: initiate a Lockout or a Clean cycle).
2. Check if the Lock Motor is running or not. If it is not running, test the wiring between the Lock Motor and the oven relay board. If the wiring is good,
check if there is 120VAC at the motor when it is expected to run to see if the failure originates from a bad motor (120VAC present but not turning) or
a problem with the relay board (J20 pin 10 on the oven relay board is the output to the Lock Motor). The Lock Motor can also be tested by applying
120VAC directly to the motor (unplug it from the relay board rst). If the Lock Motor does not run when 120VAC is applied replace the Lock Motor
Assembly. If it is the relay board that does not provide 120VAC to the Lock Motor replace the oven relay board.
3. If the Lock Motor is running but the oven control cannot nd the locked or unlocked position (ex: motor turns continuously until F90 fault code is
generated) the Lock Switch needs to be veried. Check wiring between Lock Switch and oven relay board. Verify with ohmmeter if the switch makes
contact properly (verify continuity with ohmmeter when the switch is pressed). If the Lock Switch is defective replace the Motor Lock Assembly.
4. If all above steps failed to correct the situation, replace the oven relay board.
F95 Motor Door Lock mechanism failure. The Mo-
tor Door Lock does not stop running or the
Lock Switch sends an invalid signal.
1. The problem can be caused by a faulty Lock Switch or by a defective oven relay board. If the Motor Door Lock is always running (as if the relay
controlling it is stuck closed) replace the oven relay board.
2. If the motor is not always running replace the Motor Lock Assembly.
F96 The oven door has been detected open
during a Self Clean cycle.
1. This error occurs if the door switch has lost its contact during a Self Clean cycle. Make sure the oven door closes well and fully presses on the door
switch plunger when the door is locked, and no one attempted to pull on the oven door during the Self Clean cycle.
2. Test continuity of wiring between the door switch and the oven relay board, make sure the door switch is well connected. With an ohmmeter, verify the
switch is closed when the plunger is pressed. If the door switch is found to be defective replace the door switch.
3. If the switch and wiring are good and the problem persists, replace the oven relay board.
F97 MDL invalid state. Relay board (OVC)
sensed the motor door lock in a state it
should not be in according to the user
interface board.
Replace the oven relay board.
6. Prior to returning the product to service, ensure that:
• All electric connections are correct and secure.
• All electrical leads are properly dressed and secured away from sharp edges, high-temperature
components, and moving parts.
• All uninsulated electrical terminals, connectors, heaters, etc. are adequately spaced away from
all metal parts and panels.
• All safety grounds (both internal and external) are correctly and securely reassembled.
• All panels are properly and securely reassembled.
Temperature Adjustment
1. Make sure both the oven mode selector and the oven temperature selector are in the OFF position.
Press and hold both the light icon and the clock icon at the same time for a few seconds until the
display sounds an acceptance chime. AUd should appear in the display.
2. Press the + key in the upper part of the display until UPO appears and the default setting of 0° (or the
last set temperature offset) is showing.
3. Using the + or - key in the bottom of the display, press until the desired temperature change (offset)
is reached. The display will change ± 5° with each key press to a maximum of +35° or a minimum of
–35°F. Once the new offset appears in the display, release the key and the control will accept the
change.
4. To return the display to normal, press and hold both the oven light icon and the clock icon at the same
time until an acceptance chime sounds. The display will return to show the time of day.
Note: Changing calibration affects all baking modes. The adjustments made will not change the broil
self-cleaning temperature.
MEAT PROBE TEMPERATURE VS RESISTANCE
Temperature °F (°C) Resistance (Kohm)
77 (25) 50.0 ± 7%
122 (50) 18.0 ± 4.9%
176 (80) 6.3 ± 3.3%
212 (100) 3.4 ± 4.6%
Resistance (ohms)
1000 ± 4.0
1091 ± 5.3
1453 ± 8.9
1654 ± 10.8
1852 ± 13.5
2047 ± 15.8
2237 ± 18.5
2697 ± 24.4
Open circuit/infinite resistance
RTD SCALE
Temperature °F (°C)
32 ± 1.9 (0 ± 1.0)
75 ± 2.5 (24 ± 1.3)
250 ± 4.4 (121 ± 2.4)
350 ± 5.4 (177 ± 3.0)
450 ± 6.9 (232 ± 3.8)
550 ± 8.2 (288 ± 4.5)
650 ± 9.6 (343 ± 5.3)
900 ± 13.6 (482 ±7.5)
Probe circuit to case ground
1 1
1
1
1
1
1
1
1
L1
CONVECTION FAN
J3 TO USER INTERFACE BOARD
TRITON BOARD
LATCH MOTOR
OVEN LIGHT
NEUTRAL
L1
MEAT PROBE
TEMPERATURE PROBE
DOOR SWITCH
MOTOR DOOR LATCH SWITCH
COMMON
PROGRAMMING HEADER
CONVECTION ELEMENT
BAKE ELEMENT
L1 IN
L1 IN
COM L2 OUT
NO:L2 IN
NO:BROIL
COM L1
DLB BROIL
CONV
ELEMENT
BAKE
ELEMENT
MDL
CONV
FAN
OVEN
LIGHT
NEUTRAL