Product Specifications Sheet
30" Electric Slide-In Range
Gallery
Front
30"
31
1
/2"
35
3
/4"
Adjustable
to
36
5
/8"
5
/16"
25
1
/2"
Overall
depth
including
oven door
in 90° open
position –
47
9
/16"
Power supply
connection
location (left
bottom rear)
28
5
/16"
Side
21
3
/4"
Front Face of Cabinet
22
7
/8"
min.
23
1
/4"
max.
1
1
/8"
21
3
/4"
min.
22
1
/8"
max.
**
Countertop
*Cabinet and countertop
cutout width should match
**24" with optional
backguard installed
13"
max.
30"
min.
18"
min.
24"
min.
1
/2"
min.
WALL
31
1
/2"
(critical)
30
±
1
/16"
*
Approx.
1
7
/8"
Hatched area
should be flat
and leveled
30
±
1
/16"
*
21
3
/4"
min.
22
1
/8"
max.
**
1
/2"
min.
35
7
/8"
min.
36
5
/8"
max.
Locate cabinet
doors 1" min.
from cutout
opening
3
/8"
min.
24" min. clearance
with protected cabinet bottom
30" min. for unprotected
Locate grounded
junction box or wall
outlet 8"
-
17" from
right cabinet and
2"- 4" from floor
1
1
/2"
max.
Shave raised
edge to clear
space for
31
1
/2" wide
cooktop rim
Slide-In Ranges
FGES3065P F / W / B 30" Electric
USA
•
10200 David Taylor Drive
•
Charlotte, NC 28262
•
1-800-FRIGIDAIRE
•
frigidaire.com
CANADA
•
5855 Terry Fox Way
•
Mississauga, ON L5V 3E4
•
1-800-265-8352
•
frigidaire.ca
FGES3065P 12/17 © 2017 Electrolux Home Products, Inc.
Specifications
subject to change.
Slide-In Range Specifications
•
Product Shipping Weight (approx.) – 205 Lbs.
•
Single phase 3- or 4-wire cable, 120 / 240 or 120 / 208 Volt,
60 Hertz, fused on both sides of line with ground. (If local code
permits, range may be connected by hard-wiring or by means
of power supply cord kit.)
•
Connected Load (kW Rating) @ 240 / 208 Volts = 12.6 / 9.5 kW
•
Amps @ 240 / 208 Volts = 52.5 / 45.7 Amps
•
Recommended Circuit Breaker – 50 Amps (40 Amps minimum)
•
Always consult local and national electric codes.
•
Make sure wall coverings around range can withstand heat generated
by range.
•
Linoleum or any other synthetic floor covering located beneath range,
must be capable of withstanding minimum heat of 90° F above room
temperature without shrinking, warping or discoloring. Insulating pad
or 1/4"-thick plywood required between range and a carpeted floor.
•
Countertop MUST be level in all directions and adjustable range
height at least 1/16" greater than tallest cabinet height, to ensure
metal rangetop flange will fit properly on countertop edge.
•
When installing optional Backguard Kit, cutout depth of 21-3/4"
minimum / 22-1/8" maximum needs increased to 24".
•
Overhead cabinetry should not exceed a 13" maximum depth.
•
Absolute minimum horizontal distance between overhead cabinets
installed to either side of appliance must be no less than maximum
width of appliance.
•
Allow 24" minimum clearance between rangetop and bottom of cabinet
when bottom of wood or metal cabinet is protected by not less than
1/4" flame-retardant millboard covered with not less than No. 28 MSG
sheet steel, 0.015" stainless steel, 0.024" aluminum or 0.020" copper.
Allow 30" minimum clearance when cabinet is unprotected.
•
To reduce risk of fire when using overhead cabinetry, install
range hood that projects horizontally a recommended minimum
of 5" beyond bottom of cabinets.
Countertop Preparation
Rangetop’s side flanges overlap countertop cutout edges – for detailed
preparation instructions, refer to product installation guide on the web.
•
Flat Square-Finish Countertops – require no preparation since
rangetop’s flange lays directly on countertop edge.
•
Formed Front-Edged Countertops – require front molded edge to
be shaved flat 3/4" from each front corner of opening.
•
Tile Countertops – may need trim cut back 3/4" from each front
corner of opening and /or rounded edge flattened.
•
For existing cutout width greater than 30-1/16" reduce the 3/4"
overlap dimension; for cutout width of 29", replace actual side
trim panels with smaller side trim panels, available with optional
Side Trim Kit (refer to detailed kit installation instructions).
Note: For planning purposes only. Refer to Product Installation Guide
on the web at frigidaire.com for detailed instructions.
Optional Accessories
•
Rear Filler Kit: Color-Coordinated – (Included).
•
Side Panel Kit: Stainless Steel – (PN # 903074-901S),
White – (PN # A01529902), Black – (PN # A01529901).
•
Backguard Kit: Stainless Steel – (PN # 903046-901S),
White – (PN # 903046-9011), Black – (PN # 903046-9010).
•
Side Trim Kit: Stainless Steel – (PN # 903075-901S),
White – (PN # 903075-9011), Black – (PN # 903075-9010).
Accessories information available
on the web at frigidaire.com