Spec Sheet
INSTALLATION SPECIFICATIONS
•
Product Shipping Weight (approx.) – 91 Lbs.
•
Voltage Rating – 120V / 60 Hz / 15 Amps (maximum 20 Amps if connected
with disposer)
•
Connected Load (kW Rating) @ 120 Volts = 1.44 kW
(For use on adequately wired 120V, dedicated circuit having 2-wire service
with a separate ground wire. Appliance must be grounded for safe operation.)
•
Amps @ 120V = 15 Amps
•
Always consult local and national electric & plumbing codes. Meets
requirements of ASSE 1006 — integral air gap on supply.
•
Water Pressure – Hot water line to dishwasher must provide between 20 and
120 pounds per square inch (psi) with at least 120° F hot water temperature.
•
Make sure location has correct drain, water and electrical outlets to make
connections — MUST be confined to shaded areas.
•
Electrical and water supplies should enter cabinet opening on floor, or through
back or side walls, as shown in shaded areas.
•
Keep back free of drain, water & electrical supply.
•
Connections preferably located toward left side of dishwasher. Do not cross
drain, water or electrical lines in front of motor, blower or frame.
•
If connecting drain hose to sink trap, local code may require installation of
Air Gap Kit (not included).
•
Leveling legs supplied to adjust height. (Note: Height only adjustable to
35-3/4" max. when installed in 35-3/4" max. standard cabinetry cutout.
5/16" min. clearance required from top of unit to underside of countertop.
Dimensions do NOT include insulation — insulation blanket may be
compressed during installation.)
•
When installing adjacent to wall, cabinet or other obstruction that extends
beyond front edge of unit, allow 2" minimum clearance between opened door
and obstruction.
•
Floor should be flat and free of obstructions with carpet removed to provide
motor clearance.
•
When installing at end of cabinet line, sides and back must be fully enclosed.
•
Do not install unit under a cooktop, damage will occur.
•
Recommended to seal cabinets, enclosing all sides of dishwasher, including
underside of countertop, with oil-based paint or moisture-proof polyurethane
to prevent possible steam/moisture damage.
Specifications subject to change. Accessories information available on the web at frigidaire.com / frigidaire.ca
Note: For planning purposes only. Always consult local and national electric, gas and plumbing codes.
Refer to Product Installation Guide for detailed installation instructions on the web at frigidaire.com / frigidaire.ca.
U
SA
•
10200 David Taylor Drive
•
Charlotte, NC 28262
•
1-800-FRIGIDAIRE
•
frigidaire.com
CANADA
•
5855 Terry Fox Way
•
Mississauga, ON L5V 3E4
•
1-800-265-8352
•
frigidaire.ca
FGID2479S 05/18
© 2018 Electrolux Home Products, Inc.
*Height only adjustable to 35
3
/4" max. when installed in 35
3
/4" max.
standard cabinetry cutout. (Dimensions do NOT include insulation –
insulation blanket may be compressed during installation.)
33
3
/4"
Adjustable
to 35
3
/
4
"
*
Front
23
3
/4"
24" Built-In Dishwasher w/Integrated Controls (IC)
w/Stainless Tub (ST) Gallery (Q, R & S Models)
Left
24
1
/4"
Power supply & water inlet location
(bottom rear)
50
1
/4"
Right
Door in 90°
open position
27
3
/4"
22
1
/2"
3
1
/2"
min.
to
4
1
/2"
max.
1"
2
1
/4"2
1
/4"
**
NOTE: 35
3
/4"
max.
height for standard
cabinetry cutout.
(
5
/16"
min. clearance
required from unit to
underside of countertop.)
3"
18"
24"
min.
Electrical, water,
and drain
lines
must be confined
to shaded
area
1
1
/4"
24"
3
"
90°
90°
Preferred
drain areas
3
"
34"
min.
to
35
3
/4"
max.
**
Meets
requirements of
ASSE 1006
FGID2479S D/F
DISHWASHER
24" BUILT-IN