User Manual

ManualsBrandsFRIGIDAIRE ManualsWashers134126300B

FeaturFeatur

Featur

eses

Cycle Signal Control (some models)

When the Cycle Signal Control is ON, a signal will sound at the end of each cycle and

during the Press Saver setting (some models). The volume is adjustable on some

models.

Drum Light (some models)

A drum light will come on whenever the door is opened to illuminate the dryer drum

during loading and unloading. Closing the door turns off the light.

Drying Rack (some models)

Use the drying rack to dry items which should not be tumble dried.

1. Open the dryer door and remove the lint screen.

2. Insert drying rack into the dryer drum. Place the front bar under the lip of the lint

screen opening. The side bars should sit in the notches of the frame.

3. Place items to be dried on top of rack. Weight should not exceed 10 lbs. Leave

space between items, but do not let items hang over the sides or through the

grids. Do not tumble other items when using the drying rack.

4. Select a timed dry setting best suited for items being dried. Use only the Air Fluff

(no heat) temperature setting for items containing plastic, foam rubber, rubber-

like materials, feathers or down.

5. When items are dry, remove the rack and replace the lint screen. If lint screen

is not in place, tumbling items could enter the exhaust system and cause damage

to the dryer.

Use the drying rack to dry items which

should not be tumbled.

Greasy, oily

stains

Lint

Pilling

(Fibers break off,

ball up and cling

to fabric.)

Shrinking

Wrinkling

PROBLEMPROBLEM

PROBLEM

•Rub fabric softener stains with bar soap.

Rinse and rewash.

•Reduce load size and rewash using liquid

fabric softener in the final rinse.

•Or, add a fabric softener sheet and

tumble without heat.

•Use lint brush or roller to remove lint.

•Use a lint brush or shaver to remove pills.

•Irreversible condition.

•Reduce load size and tumble at medium

or low heat for 5-10 minutes.

•Remove items immediately.Hang or fold.

SOLUTIONSSOLUTIONS

SOLUTIONS

•Add a few bath towels to small loads for proper

tumbling.

•Some "silk-like" fabrics should be air dried.

•Use proper drying temperature.

•Place fabric softener sheet on top of load before

starting the dryer.

•Do not overload dryer.

•Use fabric softener in washer or dryer to reduce

static electricity.

•Remove items when they are slightly damp to

avoid overdrying.

•Check that lint screen is clean and in place.

•Use fabric softener to lubricate fibers.

•When ironing, use spray starch or fabric finish on

collars and cuffs.

•Turn items inside out to reduce abrasion.

•Follow fabric care label directions.

•If shrinking is a concern, check load often.

•Remove items while slightly damp.

•Block knits into shape.

•Lay flat to complete drying.

•Do not overload dryer.

•Remove items as soon as cycle ends.

PREVENTIVE MEASURESPREVENTIVE MEASURES

PREVENTIVE MEASURES

POSSIBLE CAUSESPOSSIBLE CAUSES

POSSIBLE CAUSES

•Fabric softener sheet.

•Overloading.

•Overdrying causes static

electricity.

•Lint screen not clean when

cycle began.

•Lint is attached to "pills."

•Pilling is normal with synthetic

and permanent press fabrics.

This is due to abrasion from

normal wear.

•Overdrying.

•Overloading.

•Leaving items in dryer after

cycle ends.

Common DryingCommon Drying

Common Drying

PrPr

oblemsoblems

oblems

Many drying problems involve poor cleaning results, poor soil and stain removal, residues of lint and scum, and fabric damage.

For satisfactory drying results, follow these suggestions provided by The Soap and Detergent Association.