Installation Instructions READ BEFORE INSTALLING UNIT For Through-the-Wall Air Conditioners INSTALLATION WARNINGS AND CAUTION % %* * Carefully read the installation manual before beginning. Follow each step as shown. Observe all local, state, and national electrical codes and by qualified, licensed, authorized personnel only. % Pay attention to danger and safety notices.
Installation Instructions How to Install 1. Identify the wall-sleeve brand for your installation, from the chart below. Wall Sleeve Dimensions Brand Width Height Depth White-Westinghouse 25/4 15% 16, 17% or 22 Frigidaire 254 15% 16,17% or 22 Carrier (52F Series) 25% 15% 16,17'% or 22 General Electric/Hotpoint 26 15% 15% 254s 16% Fedders/Emerson* 27 16% 16% or 19% Sears/Kenmore 25% 16% 18%.
Installation Instructions 4. Prepare the wall sleeve for installation of the new unit per the following Brand instructions. #1 Emerson 15” Deep #2 Fedders 19%" Deep #3 Fedders or Friedrich #4 General Electric/Hotpoint #5 Sears or Carrier(51S Series) 16%" Deep 16%" Deep 18%" Deep #6 Whirlpool #7 Whirlpool 17%" Deep 23" Deep #8 White-Westinghouse/Frigidaire/ Carrier(52F Series) #9 White-Westinghouse/F rigidaire 16" + 17%" Deep 5.
Installation Instructions Wall Sleeve Brands: #1 Emerson 15" Deep 1. Remove existing rear grille as shown on Page 3 of this manual and replace with provided louvered rear panel. Install as shown here. NOTE: You may need to drill holes in flange of existing sleeve to match \ 80° 45" | 50° \VAvasaas eeeeeeeee Rear Louvers a“ 4" ‘ 50° new rear grille 3. Attach(2)1" x 3/8" x 14" seals to the left and right sides of the sleeve. 4.
Installation Instructions Wall Sleeve Brands: #2 Fedders 19-3/4" Deep 1. Remove existing rear grille as shown on Page 3 of this manual and replace with provided louvered rear panel. Install as shown here. NOTE: You may need to drill holes in flange of existing sleeve to match \ 80° \i Rear Louvers 4" 45" on OO out new rear grille A Top View 2. Attach (2) 472" x 3 2" x 1%" centering/support blocks one on each side wall. Place in center of side wall with the tapered end facing the opening. 3.
Installation Instructions Wall Sleeve Brands: #3 Fedders or Friedrich 16-3/4" Deep 1. Remove existing rear grille as shown on Page 3 of this manual and replace with provided louvered rear panel. Install as shown here. NOTE: You may need to drill holes in flange of existing sleeve to match new rear grille \ 80° \M Rear Louvers 4" y 45" ou oO Top View 2. Attach (2) 4%" x 3 ”" x 1%" centering/support blocks one on each side wall. Place in center of side wall with the tapered end facing the opening. 3.
Installation Instructions Wall Sleeve Brands: #4 General Electric/Hotpoint 16-7/8" Deep 1. Remove existing rear grille as shown on Page 3 of this manual and replace with provided louvered rear panel. Install as shown here. NOTE: You may need to drill holes in flange of existing sleeve to match new rear grille Rear Louvers \ 80° 4.5" <_, 50° t 50° > AMMAN LALAZZ EVAN Top View 2. Cut (2) 17" Tapered Spacer Blacks as shown below into two pieces.
Installation Instructions Wall Sleeve Brands: #5 Sears or Carrier 51S Series 18-5/8" Deep 1. Remove existing rear grille as shown on Page 3 of this manual and replace with provided louvered rear panel. Install as shown here. NOTE: You may need to drill holes in flange of existing sleeve to match \ 80" 45" 50° Rear Louvers 50° aia v \(aiwnant eeeeeees unaaniezeeees| 7 80° new rear grille A Top View 2. Install (2) tapered spacer blocks to the floor of the sleeve as shown.
Installation Instructions Wall Sleeve Brands: #6 Whirlpool 17-1/8" Deep 1. Remove existing rear grille as shown on Page 3 of this manual and replace with provided louvered rear panel. Install as shown here. NOTE: You may need to drill holes in flange of existing sleeve to match new rear grille Rear Louvers 45" 80° \ Let! 50° 5 \Thasaas eeeeeeeee 5 50° *~ Lg Top View 2. Cut (2) 17" Tapered Spacer Blacks as shown below into two pieces. pice | 4” Cut Here 3. 43" ; ‘ 4 \__ protection Pape
Installation Instructions Wall Sleeve Brands: #7 Whirlpool 23” Deep 1. Remove existing rear grille as shown on Page 3 of this manual and Rear Louvers replace with provided louvered rear panel. Install as shown here. 45" NOTE: You may need to drill holes in flange of existing sleeve to match so <> 4" on OO new rear grille Place (2) 1"x 1%" x 14" seals against each side. 3. Gently slide unit in and check if amount extending from the sleeve is sufficient once the trim frame is attached. 4.
Installation Instructions Wall Sleeve Brands: #8 White Westinghouse/F rigidaire/ Carrier 52F Series 16"+ 17-1/2" Deep 1. Remove existing rear grille as shown on Page 3 of this manual and replace with provided louvered rear panel. Install as shown here. NOTE: You may need to drill holes in flange of existing sleeve to match new rear grille Rear Louvers so 45" — AMAA 50° = 50° ULL ASSAY a t Top View 2. Attach (1) 1" x 3/8" x 25" long seal in the center ai the top of the sleeve.
Installation Instructions Wail Sleeve Brands: #9 White Westinghouse or Frigidaire 22” Deep 1. Remove existing rear grille as shown on Page 3 of this manual and replace with provided louvered rear panel. Install as shown here. NOTE: You may need to drill holes in flange of existing sleeve to match \ 80° \ Rear Louvers 4" ‘ 45" ou oO new rear grille Because of the increased unit depth, first try dry fitting using the method described below: 2. Place (2) 1"x 1%" x 14" seals against each side. 3.
Installation Instructions Direct Unit Mounting The previous directions are the preferable way to mount the new rear grill. The unit's performance is slightly better and the possibility of draughts is reduced. As a last resort, direct mounting of the grille to the unit can be considered. Note: The grille must be installed prior to inserting the unit into the sleeve. 1. Attach the 2 2. Position the a. The b. The 3. Align the top seal pieces (1"X3/8"X14") as shown in Fig. 1.
Installation Instructions FINISHING INSTALLATION: 1. Install the 1" x 1%" x 84" long stuffer seal between the wall-sleeve and the unit. A flat-bladed screwdriver or putty knife is recommended. 2. Assemble the trim frame by inserting top and bottom pieces into side pieces and snapping into place. 3. Pull cord through trim frame then slide over unit until flush with wall. ccc in ml NOTE:For larger sleeves, an accessory trim kit is available(EA120T).