Installation guide

ManualsBrandsFrigidaire ManualsRoom air conditionerOfficial Frigidaire air conditioner

installation Instructions

for Heavy duty

Please real ALL installations before installing. Two

or more people are recommended to install this

product. If a new electrical outlet is required, have

the outlet installed by a qualified electrician before

installing unit.

Preliminary Instructions

Do the following before starting to install unit, See

illustrations below.

1, Check window opening size- the mounting

parts furnished with this air conditioner are

made to install in a wooden sill double-hung

window. The standard parts are for a window

opening of 32"(812 mm) minimum to 43"(1092

mm) maximum width. Open sash to a minimum

of 20" (508 mm), (FIG, 1)

2, Check condition of window- all wood parts

of window must be in good shape and able to

firmly hold the needed screws, If not, make

repairs before installing unit,

3, Check your storm windows- if your storm

window frame does not allow the clearance

required, correct by adding a piece of wood as

shown in FIG. 2, or by removing storm window

while room air conditioner is being installed,

(Continued)

1/2" MIN.

SASH

20" MIN.

STORM WINDOW FRAME OR

OTHER OBSTRUCTION

Fig. 1

FOAM

SASH SEAL

DOUBLE

SIDED SEAL

SIDE

ACCORDION

(RIGHT)

1/4,,x11/2,,

BOLT

MOUNTING

BRACKET

END CAP & ANGLE

LEVELING LEGS BRACKET

SIDE

ACCORDION

(LEFT)

SASH

' t

il 1/2" MIN. 20" MIN.

1/2" MIN. --_i I_-- I

% Zct ss

STORM WINDOW FRAME OR ENTIRE STOOL. FASTEN

OTHER OBSTRUCTION WITH TWO NAILS OR

SCREWS.

Fig. 2

P/N:819042102-01

Summary of content (10 pages)

PAGE 1
installation Instructions for Heavy duty Please real ALL installations before installing. Two or more people are recommended to install this product. If a new electrical outlet is required, have the outlet installed by a qualified electrician before installing unit. Preliminary Instructions FOAM Do the following before starting to install unit, See illustrations below.
PAGE 2
4. CHECKFOR ANYTHING THATCOULD BLOCK AIRFLOW-check area outside of window for things such as shrubs, trees, or awnings. Inside, besure furniture, drapes, orblinds will not stop proper airflow. Tools ,/ Tape measure ,/ Adjustable wrench or pliers ,/ Pencil ./ Spirit level ,/ Socket wrenches 5. Check the available electrical servicepower supply must be the same as that shown on the unit serial nameplate, (See Owner's Guideforserial plate location.) Power cord is 48"long. Besure you have an outlet near.
PAGE 3
Window installation ! E. Be certain the proper electrical outlet is within reach of the installation. All wiring should be in accordance with local and national electrical Because the compressor is located on the controls side of the unit (right side), this side will be heavier and more awkward to manipulate. Inadequate support on control side of the unit can result in personal injury and damage to your unit and property.
PAGE 4
Window installation ! 2. Preparation to Remove the Air Conditioner From Slide-Out Chassis A. Place unit on floor, remove total of (4) Philips screws securing the chassis to the cabinet. There are (2) screws on each side. The set of screws closest to the front of the unit secure the front panel to the cabinet. The set of screws closest to the rear of the unit de Philips screws secure the cabinet to the chassis. See (Fig. 1). Fig.
PAGE 5
Window 5. Installation Sealing Strip installation of Mounting Brackets ! and the (TOP VIEW) Wslot_ NOTE: Windows _o o o o come in a variety of different styles. Therefore, it may be necessary to modify or improve your particular installation. Leve B__ o o o o ° I o .... o.... / / Bracket Assembly A. Attach the bracket assembly to 90°angle support brackets (Fig. 5) using (2) 1/4"X1 _" o 2; bolts two bolts per bracket. Secure with the (2) soppor Brackets 9O° Angle Fig.
PAGE 6
Window installation 6. Installation / of the cabinet A. Align one hole in the bottom of the cabinet with one hole in the bracket assembly. Secure the cabinet to the bracket using (3) 1/4" screws provided. Repeat the same procedure on the opposite side of the cabinet. See (Fig. 10). B. Ensure the top rail is positioned in front of the sash. The "U" shaped channel on the bottom of the cabinet should be positioned in the track provided on the bracket assembly.
PAGE 7
Window installation 9. Complete / the installation A. Cut the foam to fit the opening between the Foam top of the inside and outside window. See (Fig. 13). B. Some installations may require additional sealing around the window and air conditioner. Check for any air leaks and seal where Fig. 13 necessary. C. For -_/F/ 25K and 28K models, the condensed water will maybe overflow the unit J/ in highly humid areas.
PAGE 8
Waft Installation NOTE: Consult local building codes installation, ora qualified carpenter. Select Carefully measureand cutan following dimensions. See WIDTH "X"=265/8" (68cm) thickness of framing material HEIGHT"Y"= 185/8'' (47cm) thickness of framing material prior to Wall Location This airconditioner hasa slide-out chassis, so it can be installed through an outside wall up to 12" thick. IMPORTANT: Side louvers must never be blocked. FIG.
PAGE 9
NOTE: If wallthickness is8-1/2" ormore, add aluminum flashing over bottom of frame opening to assure no water can enter area between innerand outerwall. 4. OPTIONAL: Support brackets may be used. Installation brackets are recommended for walls under 5" thick. Refer to Step4 of Window Mounting for assembly of support brackets. A wooden strip nailed to the outside wall should be used in conjunction with sill support angle brackets, CAULK AS REQUIRED FIG.
PAGE 10
RECOMENDED: Caulking and installation of trim on interior wall may be done. You can buy wood from your local lumber or hardware supply. On the outside, caulk openings around top and sides of cabinet, and all sides ofwood sleeve to theopening. Masonry Construction 1. Cutor builda wall opening in the masonry wall similar to the frame construction (refer to Step 2 of Wall tnstallationfora wall thickness greater than 8-1/2"). 2. Secure cabinet in place using masonry nails, or the right masonry anchor screws.