Installation guide

ManualsBrandsFrigidaire ManualsRoom air conditionerOfficial Frigidaire air conditioner

For Heavy

Median {FAM

Instructions

Duty {/:AS Models) and

Models) Air Conditioners

Please read ALL instructions be_hre installing.Two people are

recommended to install this prodaetdf a new electrical outlet

is reqaired,have the outlet installed by a qaalified electrician

be_re installing anit. See#5 in Prdiminary lnstraetions

_bllowing.

Preitiminary

Do the _bHowiog be_bre startiog to iostall aoR.See illustrations

bdow.

Check dimensions of your unit to determine model type:

Heavy duD' (FAS) Median (FAM)

Unit Height: 18.5/8" 17.5/8"

Unit Width: 26 1/. 23 1/.

Min. Window Opening: 19" 18 72"

Min. Window Width: 31" 26 1/,,

Max. Window Width: 43" 40 1/2"

1°

Check window opening size =the mounting parts furnished

with this air conditioner arc made to install in a wooden

sill double-hung window.The standard parts are for

window dimensions listed aboveX)pen sash to a minimum

of i9"(483mm). (FIG. i)

2. Cheek condition of window =all wood parts of window

must be in good shape and able to firmly hold the needed

sorer s.If not, make repairs before installing uniL

FIG. 1

SASH

1/2" MIN

19" MIN

STORM WINDOW FRAME OR

OTHER OBSTRUCTION

SIDE RETAINER /

BRACKET

Check your storm windows =if your storm window

*?ame does not allow the clearance required, correct by

adding a piece of wood as shown in FIG.2, or by removing

storm window while room air conditioner is being installed.

(continued)

FIG. 2

SASH

19" MIN

1/2" MIN i 1 1/2" MIN

I _ ENTIRESTOOL,FASTEN

STORM WINDOW FRAME OR WITH TWO NAILS OR

OTHER OBSTRUCTION SCREWS.

P/N 66121623

Summary of content (8 pages)

PAGE 1
Instructions For Heavy Median {FAM Duty {/:AS Models) and Models) Air Conditioners Please read ALL instructions be_hre installing.Two recommended to install this prodaetdf is reqaired,have be_re people are a new electrical outlet the outlet installed by a qaalified electrician installing anit. See#5 in Prdiminary lnstraetions _bllowing. Preitiminary Do the _bHowiog be_bre startiog to iostall aoR.See illustrations bdow.
PAGE 2
4. CHECK FOR ANYTHING AIRFLOW- THAT COULD check area outside of window such as shrubs, trees, or awnings. BLOCK Too s for things Inside, be sure Nequired a large flat blade screwdriver flu_nimre, drapes, or blinds will not stop proper air flow. tape uleasure adjustable 5. Check the avaiiaNe deetrkai service - power suppb_ must wrench or pliers pencil be the same as that shown on the unit serial nameplate. (See Owner's Guide fbr serial plate location.
PAGE 3
Remove lnstatm Top Angl÷ and Side Bracket Chassis 1. 1hill down ftont panel axt remove filter. (See FIG. !). 2. Lift ftont upwards and place to one side. Attach tbam gasket to top angle above holes as shown in FIG. 6. 2. Install top gmgk grad side retainers to cabinet as shown in FIG. 6. 3. Locate file fimr flont screws _md remove. These screws will be needed to re=install the flont later. (See f'IG.2) 4. PU away flont flom cabinet sides as per photo (see FIG.3) 5.
PAGE 4
Rnstal! 3. Insel_ top and bottom legs of window filler panel flmne Support into chmmel in the to angle and bottom rail. Do both sides. 1. Hold each support bracket flush against outside of sill, 4. Insert washer head locking screws (2) into holes in and tight to bottom of cabinet as shown below. Mark top leg of filler panel flame (see Step 6). Do not totally brackets at top level of sill, and remove. tighten. Allow leg to slide freely. Screws will be tightened after Section 6. Place Cabinet in 1.
PAGE 5
Extend 1. Carefully Window tnstam! Chassis into Cabinet and |nstall Front to Unit Filler raise window to expose filler panel locking screws. Loosel_ screws so filler pal_els slide easily. 1, Lift air c(mditiooer al_d carefully leaving 6" protruding. 2, _DO slide ioto cabioet _ot push oft cootrols OR firmed coils. 3. Be sure chassis is firmly seated towards rear ofcabioet. 4. h-tstallation of front is the reverse of removal outlioed il_ Sectiol_ 1. 2.
PAGE 6
Thru-The-Wall NOTE: Consult or a qualified H local building codes prior to installation, Carefully carpenter. Select This air conditioner installed through Wall 12" with the following on your model. See FIGS. land 2. of *¥aming material used. Heavy (FAM) 10" Duty (FAS) Median (FAM) Inside Frame Height: 187/d' (47.9cm) 18" (45.7cm) Inside Frame Width: 263_" (67.9cm) 237 s" (60.6cm) Side louvers must never be blocked.
PAGE 7
NOTE: If wall thickmess is 8-1/2" or more, add alumimnn flashing over bottom of fimne opening to assure no water can enter area between FIG°2 inner and outer wall. 1"LONG WOOD SCREW Refer to Step 4 of Window Mounting _br assembly of support bmckets.A AL[JMINUIM FLASHING O_ER BOTTOM OF FRAME wooden strip nailed to the outside wall should be used in conjunction with sill support angle brackets. Prepare Cabiaet and lasta 1. Slide chassis fiom cabinet. Reier back to Step 1 of Window Mounting.
PAGE 8
OPTIONAL:Cmllkingandinstallation of tfimoninterior wallmaybedone.YoucanbuywoodIiomyourlocallumber orhardware supply. Ontheoutside, caulkopenings aroundtop andsidesof cabinet, andallsidesof woodsleeve totheopening. NOTE: SeeStep7,Item3of WindowMountingInstructions lot bottomrailseallocation. Masen Construction 1. Cut or build a wall opening in the in,f_sonFyvcall $11Y1i1,5_1 to the fiame constmction(reler Installation to Step 2 of Thin=the=Wall lot a wall thicM3ess greater than 8=1/2"). 2.