Installation guide

ManualsBrandsFrigidaire ManualsRoom air conditionerOfficial Frigidaire room air conditioner

INSTALLATIONINSTRUCTIONS

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any too(s listed

here.

Took Needed

[] Flat=blade and Phillips [] Tape measure

screwdrivers

[] Drilland %2" orsmallerbit

[] Level

Through=the=Wall Installation:

In addition to the tools listed above, the following tools are

needed for through4he-waU installation.

[] Saw [] 1" (2.Scm) orthicker

lumber

[] Wood preservative

[] Caulk [] #10 x l" wood screws (7)

IMPORTANT: Observe all governing codes and ordinances.

Check the location where air conditioner will be installed. Proper

installation is your responsibility, Make sure you have everything

necessary (or correct installation.

The location should provide:

[] Grounded electrical outlet within 4 ft (I 22 cm) of where the

power cord exits the air conditioner.

NOTE: Do not use an extension cord.

[] Free movement of air in room to be cooled.

[] A large enough opening for the air conditioner,

[] Adequate wallsupportforweightof air conditioner. Air

conditioner weighs between 70 and 851bs (32 to 40 kg),

NOTE: Cabinet louvers must not be obstructed. Air must be able

to pass freely through the cabinet louvers.

Parts Supplied (on some models)

Check that all parts are included in parts package.

E F

A. Foam window sash seal

B. Window lock bracket

C. Side curtains (2)

D. Foam seal

E. #10x 7/2"pan-head Phillipsscrews (3)

F. #10x _" round-head screws (6)

G. Top channel

H. #10x ¼" pan-head Phillips screws (3)

A. Cabinet louvers

NOTE: Installation parts are supplied (or double-hung windows

up to 36" (91.4 cm) wide. A special Wide Window Kitis available

from your dealer or service center. See "Accessories."

NOTE: DO NOT USE ANY SCREWS OTHER THAN

THOSE SPECIFIED HERE

PiN 2020213A0016 1

Summary of content (7 pages)

PAGE 1
INSTALLATIONINSTRUCTIONS Gather the required tools and parts before starting installation. Read and follow the instructions provided with any too(s listed here. IMPORTANT: Took Needed [] Flat=blade and Phillips screwdrivers [] Level [] Tape measure [] Drilland %2" orsmallerbit Observe all governing codes and ordinances. Check the location where air conditioner will be installed. Proper installation is your responsibility, Make sure you have everything necessary (or correct installation.
PAGE 2
Window Installation Window opening measurements: [] 27" to 36" (68.6 cm to 91.4 cm) opening width. [] 17"(43.1cm) minimum opening height. mA__t_ B { ,r [:7_ =_ 1 I A. 27"(68.6cm) minimum B. 17" (43.1cm) minimum Through=the=Wall Installation The wall opening measurements should be: [] Width: 22s/8"(57.5 cm) plus twice thickness of wood used to build frame. [] Height: 16" (40.6 cm) plus twice thickness of wood used to bui{d frame. [] Depth: 2_/2" (6.4 cm) minimum to 6V2" (16.5cm) maximum. ? .
PAGE 3
iNSTALLATiON iNSTRUCTiONS Excessive Weight Hazard Use two or more people to move and install air conditioner, 4. Pull on the handles to slide the air conditioner out of the cabinet. Place the air conditioner on cardboard. Failure to do so can result in back or other injury.
PAGE 4
NOTES: [] Handle theairconditioner gently. [] Besureyourairconditioner cabinetdoesnotfalloutofthe opening duringinstallation orremoval. 3.Insertthetopandthenthebottomoftheright-hand curtain housing inthetopandbottomcurtain channels ontheair conditioner. The place where the power cord exits the air conditioner should be no more than 4 ft(122 cm) from a grounded 3 prong outlet. [] Do not block the louvers on the front panel. [] Do not block the louvers on the outside of the air conditioner.
PAGE 5
Install Cabinet into Window Attach Side Curtains Handle the air conditioner gently. Be sure your air conditioner cabinet does not fall out of the opening during installation or removal. The place where the power cord exits the air conditioner should be no more than 4 it (1 22 cm) from a grounded 3 prong outlet. to Window Frame 1. Pull the left-hand curtain out until itfits into the window channel.
PAGE 6
Complete Installation C 1. Insertseal behind the top of the lower window sash and against the glass of the upper window. 2. Place the window-lock bracket on top of lower window and against upper window sash on right side of the window. 3. Use a 3/32"drill bitto drill starter holes through the holes in the bracket into the window sash. 4. Attach the window lock-bracket to the window sash with 2-#10 x 3/4_'round-head screws to secure window in place. A A, Window lock B. Upper window C.
PAGE 7
• Use 1" (2.5 cm) or thicker lumber for wood frame. 2. Use a level to check thatcabinetis level side to side. A. Level 3, A, Outside width B, Outside height C. Depth Check thatairconditionercabinetis tilted to the outside so that water will run to the outside.The cabinet should slope at least half-a-bubble towards the rear, 4, Reuse the insulation to seal opening between cabinetand frame, 5, Attach frame securely to the wall.