Installation guide

ManualsBrandsFrigidaire Manualswall ovenOfficial Frigidaire electric wall oven - 5995297784

INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and liquids in

the vicinity of this or any other appliance.

Your new wall oven has been designed to fit a limited variety of cutout sizes to make the job of installing

easier. The first step of your installation should be to measure your current cutout dimensions and

compare them to the cutout dimensions chart below for your model. You may find little or no cabinet

work will be necessary.

Do not remove spacers (if equipped) on the side walls and/or on the back of the built-in oven.

These spacers center the oven in the space provided. The oven must be centered to prevent excess heat buildup

that may result in heat damage or fire.

r .... , * Suggested distance from floor is 31 " (78.7 cm)

openings "'_,_l ..... |27" Min.

MJmmum required distance Js4 1/2" (11.4 cm) (68.6 ___

Cutout

_ for self-clean models.

Minimum required distance is 10" (25.4 cm)

................ for easy-clean models. 1 1/2"[_'_

_:_ (3 8 cm) I

Do not install the oven ........ t" 28 3/32" / I

:...... / 71.4 cm) H I

closer than the

Door / II

I dimension "K" (see EOpen / ....

table) toanyadjoiningcabinetryor _ re _ _

walls on the door hinge side. This will

interfere with oven rackremovakFigure2 i: : i':i'" ! (7___

NOTE:

- Self-clean Models: Allow at least 27 ¼" (

clearance for door depth when it is open.

- Easy-clean Models: Allow at least 26 ¼" (66.7 cm)

clearance for door depth when it is open. 2" (5 cm) Wide Wood

Spacer if Needed

NOTE: For a cutout height greater than 29" (73.6 cm) add

one 2" (5 cm) wide wood spacer to each side of the opening

under the appliance side rails.

Electrical Junction box

location and Hole for

Cable space 2"(5.1 cm)

from left wall for Self-

Clean Models.

Electrical junction box

"" --_,/ and Hole for Cable

G_-/'=I space 2" (5.1 cm)

_i from right wall for

Easy Clean Models.

" "; _3"(7.6 cm)

.-. Max.

Electrical junction box

2" (5.1 cm)

Min. (right or left side

depending of model)

NOTE: Base must be capable of supporting 150 pounds (68 Kg).

Figure 1

27" (68.6 cm) Easy Clean

27" (68.6 cm) Self Clean

26 7/8 (68.2)

30 9/16 (77.6)

31 1/8 (79.1)

24 11/16 (62.7)

24 1/4 (61.6)

25 3/8 (64.5)

27" (68.6 cm) Easy Clean 24 7/8 (63.2) 25 5/32 (63.91 23 1/2 (59.7) 28 1/8 (71.4) 29 5/8 (75.2) 3 (7.6)

27" (68.6 cm) SelfClean 247/8(63.2) 25 1/4(64.1) 23 1/2(59.7) 28 1/8(71.4) 30 1/8(76.5) 41/2(11.4)

All dimensions are in inches (cm).

Some models are not available in Canada. P/N 318201508 (0201) Rev.

English - pages 1-9

1 Espa_ol - pctginas 10-18

Fran_ais - pages 19-27

Summary of content (28 pages)

PAGE 1
INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER. IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE. READ AND the vicinity SAVE THESE Do not remove that spacers may FOR FUTURE FOR YOUR SAFETY: Do not store or use gasoline of this or any other appliance. Your new wall oven has been designed easier. The first step of your installation compare them to the cutout dimensions work will be necessary. These INSTRUCTIONS result center in heat r spacers the oven damage ....
PAGE 2
grounded branch circuit, protected by a circuit breaker or fuse, having amperage as noted on the rating plate (the rating plate is located on the oven frame). Important Notes to the Installer 1. Read all instructions contained in these installation 2. 3. 4. 5. instructions before installing the wall oven. Remove all packing material from the oven compartments before connecting the electrical supply to the wall oven. Observe all governing codes and local ordinances 1.
PAGE 3
4. Electrical Wait at least three (3) hours after receiving this built-in oven before switching the power on to prevent possible damage to the built-in oven control at power on. 3. Adjusting It is the responsibility and obligation of the consumer to contact a qualified installer to assure that the electrical installation is adequate and is in conformance with the National Electrical Code ANSI/NFPA No. 70qatest edition, or with CSA Standard C22.
PAGE 4
, If used in mobile homes or if local codes DO 5. Preparing NOT permit connection of the frame grounding conductor to the neutral (white) wire, separate the white and bare copper ground wires that extend out of the end of the supply cable of the appliance. Connect the white wire from supply cable to the neutral white wire in the junction box. Connect the black and red wires from the supply cable to the matching color wires in the junction box.
PAGE 5
10. Reassemble the handle and filler plates #2, #3 and #12 on the opposite side of the door. 11. Remove and relocate the filler plates #7 on the opposite side of the oven frame. 12. Remove the latch pin #10 and relocate latch on the opposite side of the oven door. 13. Invert positions of #8 and #9 hinge fixed parts (ex. from top left side bottom right side). 14. Reassemble the door onto wall oven; insert door into the fixed lower hinge, the proceed with the reassembly of the upper hinge.
PAGE 6
8. 9. Turn the outer door assembly a half turn (180 °) and replace the outer door assembly over the lower door assembly. Replace the nylon slide under the handle (thin side facing inward) on the same side of the ball screw. Replace the 2 screws under the door and the 3 screws on top of the door. 18. Move the oven light switch to the left side of the oven frame: a) b) Turn the door so the external panel faces the work table.
PAGE 7
5. Cabinet Installation B. Self Clean A. Easy Clean Models 1. Remove and lay aside the lower vent trim which is taped to the oven outer side panel. 2. Slide the oven into the opening until the side trims fit flush against the wall of the cabinet and check for levelness of the oven racks. Shim as required. Check the levelness of an oven rack with a spirit level. 3. Using the holes in the oven front frame as template, drill four 1/8" (3 mm) diameter hols in the cabinet. 4.
PAGE 8
Only certain cooktop models may be installed over certain built-in electric oven models, listed by the MFG ID number (see the insert sheet included in the literature package). Side filler panels are necessary to isolate the unit from adjoining cabinets. Panel height should allow for installation of approved cooktop models. To reduce the risk of personal injury and tipping the wall oven, the wall oven must be secured to the ca binet(s) by properly installed anti-tip (mounting) screws.
PAGE 9
I _1_ 18" (45.7 cm) Max. _I I I 4" (10.2 cm) " Flexible Appliance Conduit - - -FlareUnion Pressure Regulator Cabinet sides or _" filler panel 6.
PAGE 10
LA INSTALACIC)N IMPORTANTE: Y EL SERVICIO DEBE DE HACERLOS GUARDE ESTAS INSTRUCCIONES LEA Y GUARDE UN INSTALADOR CALIFICADO. PARA USO DEL INSPECTOR ELI_CTRICO LOCAL. ESTAS INSTRUCCIONES PARA FUTURAS REFERENCIAS. PARA SU SEGURIDAD: No almacene ni utilice gasolina u otros vapores y liquidos inflamables en la proximidad de este o de cualquier otro artefacto.
PAGE 11
Notas importantes para el instalador 1. Lea todas las instrucciones antes de instalar el horno. 2. Saque todo el material usado en el embalaje del compartimiento del horno antes de conectar el suministro el_ctrico o de gas a la estufa. Observe todos los c0digos y reglamentos pertinentes. Deje estas instrucciones con el consumidor. ESTE HORNO NO ESTA APROBADO PARA LA INSTALACI_N DE RIMERO O DA LADO A LADO. 3. 4. 5.
PAGE 12
_ Cuando utilice su horno empotrado 4. Conexibn por la primera vez, espere por Io menos tres (3) horas antes de conectarlo al suministro el_ctrico. Los controles el_ctricos pueden ser daflados el_ctrica. 3. Ajustando al conectar la Altura el horno El usuario tiene la responsabilidad personal y obligaci6n de utilizar un instalador calificado, para asegurar que la instalaci6n el_ctrica est,1 hacha de forma adecuada y est,1 conforme con el C6digo El_ctrico Nacional ANSI/ NFPA No.
PAGE 13
= Si este horno se va a usar en una casa sobre 5. Preparacibn ruedas o si los cbdigos locales NO permiten que el armaz6n este conectado al neutro (blanco) de A. Modelos del homo f_cilmente a pared limpiables Este horno de pared puede modificarse facilemente para abrirse al lado izquierdo o al lado derecho.
PAGE 14
8. 9. Deslize y ajuste el panel de vidrio a la esquina la puerta interna de acero esmaltada (hacia nueva ubicaci6n del tirador). de la 3 tornillos El perno Buje de la Soporte de la bisagra (2 lugares) bisagre de la puerta Invierta la ubicaci6n de los contramarcos # 5 y # 6 (contramarco # 5 abajo y contramarco # 6 arriba); vuelva a montar los contramarcos. Modelos auto luz del homo bisagre de la puerta del del Horno Se debe apagar la corriente el_ctrica invertir la puerta.
PAGE 15
Tornillo de amortizador la puerta Amortizador de _- Buje de la enroscado para volver a montar luego. 15. Mueva los 3 tornillos de bisagra postizos del lado derecho inferior del armaz6n del horno al lado Tornillo de bisagra de la parte superior de la puerta de € izquierdo superior del armaz6n del horno. 16. Reponga el soporte de bisagra que se quit6 en el n0mero 14 al lado derecho inferior del armaz6n del horno.
PAGE 16
5. Instalacibn A. Modelos 1. 2. 3. 4. 5. del Gabinete f_cilmente B. Modelos limpiables Introduzca Retire y ponga a un lado la rejilla baja de ventilaci6n que esta pegada a la parte exterior del panel lateral del horno. Deslize el horno en la apertura hasta que los contramarcos laterales se ajustan correctamente contra la pared y verifique que esta a nivel. Luego aflade las cutlas como sea necesario. Pase el conducto el_ctrico a trav_s del orificio en el fondo limpiables el recortado.
PAGE 17
Se puede instalar solamente ciertos modelos de estufas por encima de ciertos hornos a pared el_ctricos, listados seg0n el n0mero del MFG ID (consulte la hoja inclu[da en el paquete de literatura). Para reducir el riesgo de da_os personales y de que vuelque el homo a pared, el horno debe fijarse a los gabinetes con unas mdnsulas antivuelco correctamente instaladas. Paneles Ilenadores laterales son necesarios para aislar el horno de los gabinetes adyacentes.
PAGE 18
" (45.7 cm) Max. 4" (10.2 cm) Conector flexible para artefactos Tomacorriente puesto a tierra de 120V/60Hz Adaptor de gas Lado derecho del gabinete Regulador de presi6n Ladosdel gabinete o panel Ilenador V_lvula de cierre manual Gabinete del horno a pared INSTALACION 6. Revisi6n Algunos Consulte de horno funcionen Figura 13 - MODELOS AUTO LIMPIABLES SOLAMENTE TiPICA PARA UNA ESTUFA DE GAS ENCIMA DE UN HORNO INSTALADO DEBAJO DEL MOSTRADOR hornos a pared tienen controles manuales.
PAGE 19
L'INSTALLATION ET L'ENTRETIEN DOIVENT f:TRE EFFECTUI_S PAR UN INSTALLATEUR QUALIFII_. IMPORTANT : CONSERVEZ POUR L'INSPECTEUR D'I_LECTRICITI_ LOCAL. LISEZ ET CONSERVEZ CES INSTRUCTIONS POUR RI_FI_RENCES ULTI_RIEURES. POUR VOTRE SI_CURITI_ : N'entreposez inflammables & proximit6 de cet appareil pas ou n'utilisez ou de tout autre appareil pas d'essence ou d'autres produits 61ectrom6nager.
PAGE 20
Installateur Observez tous les r_glements et les codes Iocaux applicables. 1. Un c_ble _lectrique _ 3 ou 4 fils de 120/240 ou 120/208 Volt monophas_, 60 Hz CA est requis sur un circuit s_par_ muni d'un fusible sur chaque fil conducteur (fusible temporis_ ou disjoncteur recommand_). NE RELIEZ pas de fusible au neutre. La capacit_ du fusible ne doit pas exc_der la capacit_ nominale du circuit de I'appareil sp_cifi_e sur la plaque signal_tique.
PAGE 21
r l_l_'_lTi_l II faut attendre au moins trois (3) heures apr_s sa r_ception avant de mettre I'appareil sous tension pour _viter toute possibilit_ d'endommager la commande du four Iors de la mise sous tension. 3. R glage de la hauteur 4. Connexions du four encastr Lorsque requis, ce four peut _tre ajust_ en hauteur pour en permettre I'installation dans le d_coupage existant d'une armoire. Pour r_gler la hauteur du four: 1. D_posez le four sur sa paroi arri_re. 2.
PAGE 22
. Si I'appareil est utilisd dans une maison mobile, ou si les codes Iocaux N'AUTORISENT PAS une connexion du conducteur de mise & la terre du ch&ssis au neutre (blanc), s_parez le fii blanc du fii d_nud_ en cuivre de mise _ la terre du c_ble 5. Prdparation A. ModUles du four faciles encastrd & nettoyer Ce four encastr_ peut facilement _tre modifi_ pour que la porte s'ouvre soit du c6t_ droit ou du c6t_ gauche.
PAGE 23
9. R_assemblez les moulures inversant leurs positions la #6 en haut). #5 et (la moulure #6 tout en Pour inverser I'ouverture de la porte, vous devez embaucher un technicien d'exp_rience afin de pr_venir tout dommage aux pi_ces ou des probl_mes d'alignement de la porte. #5 en bas et 10. R_assemblez la poign_e et les obturateurs #2, #3 et #12 sur I'autre c6t_ de la porte. 11. Retirez les obturateurs #7 et placez-les du c6t_ oppos_ du cadre avant du four. 12.
PAGE 24
9. Retournez la porte, le panneau ext_rieur face _ la table de travail. Inversez la position de la cheville du Ioquet avec le bouton de la cheville du Ioquet du c6t_ oppos_ de la porte. NOTE: La cheville du Iocquet de la porte est d_salign_e par rapport aux trous de montage de cette piece et sa position sur la porte est tr_s importante. Une installation incorrecte peut causer un _clatement du fini _maill_ du cadre avant en fermant la porte.
PAGE 25
5. Installation dans I'armoire A. ModUles facile _ nettoyer 1. Retirez la moulure inf_rieure qui est attach_e sur le c6t_ du four _ I'aide de rubans adh_sifs. 2. Glissez le four encastr_ dans I'ouverture murale jusqu'_ ce que les moulures lat_rales s'appuient _galit_ sur le mur de I'armoire. V_rifiez si les grilles du four sont de niveau et ajustez le four en consequence, _ I'aide de cales plac_es sous sa base. D_poser le niveau sur une grille du four pour v_rifier si le four est de niveau. 3.
PAGE 26
Seul certains modules de plaque de cuisson peuvent _tre superposes sur certains modules de four _lectriques encastr_s, _num_r_s par num_ro d'identification du fabricant (voir la feuille annex_e dans I'enveloppe documents). Pour pr_venir tout basculement du four encastr_ et des blessures, il faut fixer le four I'armoire & I'aide des vis anti- bascules correcte-ment install_es. Des panneaux lat_raux sont n_cessaires pour isoler I'unit_ des armoires adjacentes.
PAGE 27
18 po (45.7 cm) Max. )o (10.
PAGE 28