Installation Instructions

Dishwasher
Installation
Instructions
INSTALLER: Leave Installation Instructions with owner.
OWNER: Read your dishwasher Use & Care Guide. It contains important
safety information for operating this appliance. It also has many suggestions
for getting the best results from your dishwasher. Keep these instructions with
your Use & Care manual for future reference.
If you have an installation problem, contact your dealer or installer. You are
responsible for providing adequate electrical, exhausting and other connecting
facilities.
Skill Level: Installation of this dishwasher requires basic mechanical and elec-
trical skills. Proper installation is the responsibility of the installer. Product failure
due to improper installation is not covered under the warranty.
Completion Time: 1 to 3 Hours. New installations require more time than
replacement installations.
Safety Precautions: The following warnings, cautions, and the important
safety instructions DO NOT cover all possible conditions and situations that
may occur. It’s your responsibility to use common sense, caution, and care
when installing, maintaining, and operating the dishwasher DO NOT attempt
to install or operate your unit until you have read the safety precautions in
this manual. Safety items throughout this manual are labeled with a Danger,
Warning, or Caution based on the risk type.
Printed in U.S.A. P/N: A16308101 RevA (1811)
WARNING
Read and observe all CAUTIONS and WARNINGS shown throughout these
instructions before installing dishwasher. This guide will help you anticipate
drain, water, and electrical connections, and help you select the best location
for the dishwasher.
As with all equipment using electricity, water and moving parts, potential
hazards exist. To safely operate this appliance, become familiar with its
operation and exercise care when using it.
1
Before You Begin
WARNING
Install and store the dishwasher inside, away from exposure to weather.
DO NOT install the dishwasher in a location where the water may freeze (where
the temperature falls below 32°F (0°C). Frozen water in the hoses, pipes, or
other components may damage the dishwasher.
Denitions
This is the safety alert symbol. It is used to alert you to potential personal
injury hazards. Obey all safety messages that follow this symbol to avoid
possible injury or death.
Safety Precautions: The following warnings, cautions, and the important safety
instructions do not cover all possible conditions and situations that may occur.
It’s your responsibility to use common sense, caution, and care when installing,
maintaining, and operating the dishwasher DO NOT attempt to install or
operate your unit until you have read the safety precautions in this manual.
Safety items throughout this manual are labeled with a Danger, Warning, or
Caution based on the risk type.
WARNING
FIRE HAZARD
Do not install the dishwasher on a carpet.
2
Preparing for Installation
Materials and Tools
Parts Supplied*
• Installation brackets (x2)
• ST3.5*9 screws (x2)
for installation bracket
• ST4*14 screws (x2)
for installation bracket
• Condensation strip
• Adjustment caps (x2)
• Cable tie for drain hose
• Adjustable toeplate
Parts Needed for Installation
(Not supplied)
• Twist on wire connectors (x3)
• Strain relief
• Tape (electrical tape and standard
duct tape)
• Hot water supply line
• 90° Elbow
• Tubettings
• Air gap
• Rubber connector
• Hose clamp
• Power cable
(if not able to hard wire)
• PTFE thread seal tape or sealing
compound
Tools needed for installation
• Drill and appropriate bits
• Safety glasses
• Gloves
• Flashlight
• Adjustable wrench
• Wire stripper
• Pliers
• Nipper
• Measuring tape
• Pencil
• Phillips screwdriver
• Flat screwdriver
• Tubing cutter
• Utility knife
• Hole saw set
• Level
• Torx
®
T20 driver
• Hex L-wrench set
Before starting the installation, prepare all the necessary tools and parts
required to install the dishwasher. This will save installation time and simplify
the installation process.
* Provided with the dishwasher. Check that all parts are present when
unpacking the dishwasher.
WARNING
TIP OVER HAZARD
• DO NOT use dishwasher until completely installed.
• DO NOT push down or place excessive weight on open door.
DANGER
DANGER indicates an imminently hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING
WARNING indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION
CAUTION indicates a potentially hazardous situation which, if not avoided,
may result in minor or moderate injury.
IMPORTANT
Indicates installation, operation, or maintenance information which is
important but not hazard-related.

NOTE
Water supply line, power cable and drain hose will run through the bottom
channels from the back to the front connections.
Enclosure dimensions

NOTE
This dishwasher is designed to be enclosed on the top and on both sides by
a standard residential kitchen cabinet unit. The installation enclosure must
be clean and free of any obstructions.
The enclosure must be at least 17.7 inches wide 23 inches deep and 32.5
incheshigh.Forthefrontdoorofthedishwashertobeushwiththeleading
edge of the counter top, the counter top must be at least 23 inches deep.
IMPORTANT
DO NOT use plastic tubing. Plastic tubing can deteriorate over time and
causealeakinsidethetubetting.
Coppertubingwithacompressionttingoraexiblestainlesssteelbraided
hot water supply line should be used for the hot water supply line.
3
Roughing In

NOTE
New installation
If the dishwasher is a new installation, most of the installation work must be
done before the dishwasher is moved into place.
Replacement
If the dishwasher is replacing an old dishwasher, you must check the
existing dishwasher connections for compatibility with the new dishwasher.
Replace the existing connections as necessary.
1. Make sure your location has the right drain, water, and electrical outlets to
make the connections. DO NOT install unit under a cooktop range, damage
to plastic tub will occur.
IMPORTANT
If unit is to be placed in a corner, there must be at least a 2” side clearance
to open door.
• Thelocationmusthaveasolidoorthatisabletosupporttheweight
of the dishwasher.
• The location must be near a sink with easy access to the water supply,
drain, and electrical outlet.
• The dishwasher must be installed within 9.8 ft (3 m) of the sink.
• Thelocationmusthavesufcientspaceforthedishwasherdoorto
open easily and provide enough space between the dishwasher and the
cabinet sides of at least 0.1 in (2 mm).
• The back wall of the enclosure must be free of obstructions.
2. Remove any carpet from area to provide motor clearance. Floor should be
atandfreeofanyobstruction.
IMPORTANT
Drain, water, and electrical lines should be roughed-in before going any
further.
For new installations only
1. Using a hole saw, cut a hole into the side of the cabinet that holds the sink
for water line supply, drain hose and power cables, as shown below.
2. Ifthebaseinsidethesinkcabinetisraisedabovethekitchenoorandis
higher than the connections on the dishwasher, make a hole in the base
inside the cabinet and in the cabinet side.

NOTE
Depending on where your electrical outlet is, you may need to cut a hole in
the opposite cabinet side.
17.7" (450mm)
minimum
23" (580mm)
minimum
32.5" (825mm)
minimum
WARNING
ELECTRIC SHOCK HAZARD
Observe all local codes and ordinances for electrical and
plumbing connections. All electrical and plumbing work should
beperformedbyqualiedpersons.Failuretofollowthis
warning could result in death or serious injury.
4
Connections (Water and Electrical)
1. Adjust the water heater to deliver water between 120°F (49°C)–135°F
(57.2°C). This temperature range provides the best washing result and
shortest cycle time. Temperature should not exceed 135°F (57.2°C) to
prevent damage to dishes.
2. Turn OFF water supply valve.
3. SealthehotwatersupplylineconnectionsusingTeontapeorsealing
compound to stop any water leakage.
IMPORTANT
The hot water supply line pressure must be between 20 psi–120 psi
(0.14 MPa–0.82 MPa).
Preparing Hot Water Line Connection
Preparing Electrical Line Connection
WARNING
ELECTRIC SHOCK HAZARD
The electrical service must conform with all state, municipal,
provincial and/or local codes and ordinances and the latest
edition of the National Electrical Code, or in Canada, the
Canadian Electrical Code CSA C22.1 latest edition.
WARNING
ELECTRIC SHOCK HAZARD
Direct connections require:
•Theuseofexible,armoredornon-metallicsheathed,copper
wire with a grounding wire that meets the wiring requirements
for your local codes and ordinances.
• The use of strain relief method provided with the wiring
junctionboxorinstallaU.L.-listed/CSA-certiedclamp
connector to the wiring junction box. If using conduit, use a
U.L.-listed/CSA-certiedconduitconnector.
Hot water
supply line
Power
cable
5 ⅓ ~ 7⅓ in.
(135 ~ 185mm)
5 1/3~7 1/3 in.
(135 ~ 185mm)
Hot Water
Supply Line
Power Cable
Dishwasher bottom
Side View Front View
17.6” (450 mm)22.6” (575 mm)
32.4” 825 mm
5
Unpacking and Inspection
IMPORTANT
Unpack the dishwasher in an open area free of obstruction both around the
carton and overhead. Retain the carton and all of the packing materials until
the dishwasher is fully installed and operational to ensure you have removed
all the product’s components from the carton prior to disposal.
1. Cut or unbuckle the four straps securing the top
of the carton.
2. Lift the carton up and over the dishwasher and
placeitontheoor.
3. Place the straps and all packing materials from
around the dishwasher inside the empty carton,
inspecting them for any signs of damage.
4. Lift the dishwasher from the carton tray, and
thenplaceitontheoor.
5. Locate and set aside the dishwasher’s installation
parts package and toeplate. The toeplate is
attached to bottom of the carton tray. Place carton tray into the carton.
WARNING
ALWAYS LIFT THE DISHWASHER TO MOVE IT. Sliding it over rough
surfacescandamagethedishwasher’sfeetandslidingthefeetovernished
surfacescan,insomecases,damagethatnishortheunderlyingsurface.
IMPORTANT
DO NOT, under any circumstances, remove the sound-absorbent padding
that surrounds the exterior of the tub of the dishwasher.
7. There is also packing inside the dishwasher that you may want to leave in
place until the dishwasher is installed.
Unpacking the dishwasher
Inspecting the dishwasher
Mechanical inspection
1. Check the plastic base assembly to ensure that it is intact.
2. Check the dishwasher’s feet to ensure they are in place and can be
adjusted so you can level and secure the dishwasher.
3. Check all the visible components on the bottom of the dishwasher to
ensure they are intact and secure.
4. Checkthedoorlatch,theoperationofthehinges,andconrmthedooris
properly secured to the dishwasher.
5. Remove the two screws securing kickplate to dishwasher and remove
kickplate. Set aside kickplate and screws to replace when unit is installed.
Plumbing inspection
1. Check the hot water connection on the left side at the front of the base of
the dishwasher. The mounting plate should be secured to the front of the
base, the threads inside the connection should be smooth and shiny, and
the area should be clean and free of any debris.
2. Check the plastic Brake and Sensor cases to ensure these assemblies are
not cracked and that all connections are secure.
3. Check the drain hose for any holes or deformities that could allow a water
leak during draining.
Electrical inspection
1. Conrmthejunctionboxcoverissecuredtothejunctionboxonthefront
right-side of the base of the dishwasher.
2. Conrmtheelectricalboxwasnotdamagedduringshippingandthatitis
secured to the base of the dishwasher.
Visual inspection
1. Conrmtherearenodentsorscratchesonthefrontofthedishwasher.
2. Check the edges of the doors for any roughness or cracking.
3. Check the control panel to ensure it is clear and unscratched, and that all
the control markers are in their proper places.
6
Installing the Dishwasher
Preparing the dishwasher
WARNING
ELECTRIC SHOCK HAZARD
Disconnect electrical power at the fuse box or circuit breaker
box before removing old dishwasher or beginning new
installation. Failure to follow this warning could result in
death or serious injury.
WARNING
ELECTRIC SHOCK HAZARD
Prior to removal of original dishwasher and the installation of your new
unit, make sure to switch off your circuit breaker. Do not connect the
dishwasher until you have completed the installation. Connecting the
power cable is the last step when installing the dishwasher.
Teflon tape or
sealing compound
90°
Elbow
Inlet Valve
CAUTION
Do not overtighten the 90° elbow. Doing so may damage the water inlet
valve and cause a water leak.
Verify that the circuit breaker and water supply valve are off before proceeding
with the following steps.
1. Make sure there are no kinks in the water hose and that it is not bent at
anyanglesthatcouldconstricttheowofwater.
2. Remove the junction box cover located at the bottom front right of the
dishwasher using a screwdriver, and install the strain relief. Keep the
junction box cover to replace after wiring is completed.
WARNING
ELECTRIC SHOCK HAZARD
• Electrically ground the dishwasher.
• Connect the ground wire to the green ground connector in
the junction box.
• DO NOT use extension cord.
Toreducetheriskofelectricalshock,re,orpersonalinjury,the
installer must ensure that the dishwasher is completely enclosed at
the time of installation.
Strain relief
Junction box
3. Connect the 90° elbow joint to the inlet valve from the front of the
dishwasher.UseTeontapeorsealingcompoundtosecure.
4. Secure dishwasher to the countertop if the countertop is made of
wood or a material that is not damaged by drilling.
To attach the two installation brackets to the top of the dishwasher, insert
each bracket tab into the corresponding slot on the top of the dishwasher.
Tighten using screws ST3.5*9 provided with the unit.
1
2
3
Product dimensions
1
2
3

NOTE
Remove toeplate and parts package from the bottom of the carton tray.
6. Remove the bag that protects the dishwasher during shipping.
Secure dishwasher to the cabinet side wall if the countertop can
be damaged by top mounting the unit. To attach the two installation
brackets to the side of the dishwasher, remove the adjustment caps from
the sides of the unit. Use pliers to snap off the end of the long leg of the
bracket. Insert each bracket tab into the corresponding slot on the side of
the dishwasher and tighten using screws ST3.5*9 provided with the unit.
Required parts
Conrmthatyouhaveallthepartssuppliedbythemanufacturer(seethe
Material and Tools section of this Installation Instruction).