Use and Care Manual

5
OPERATING INSTRUCTIONS
Option Selections (*available on
select Models)
*Sanitize Option
To sanitize your dishes and glassware, select
SANITIZE option. When selected, the light
above the pad will come on and remain on until
end of cycle. The water temperature in the
fi nal rinse will be raised to 155
o
F (68
o
C) and will
maintain that temperature for 9 minutes. This
option is available in Heavy and Normal Cycles.
Only these sanitization cycles have been
designed to meet NSF requirements.
The cycle time will be extended until the proper
water temperature is reached.
Washing
action will continue during the water heating
delay. For best results, the incoming water
temperature should be at least 120
o
F (49
o
C).
The sanitize criteria may not be satisfi ed if there
is an interruption of the cycle, power failure or if
the incoming water temperature is below 120
o
F
(49
o
C).
To turn off the SANITIZE option, press the pad
a second time. The light above the pad will
turn off.
*Hi-Temp Wash Option
When HI-TEMP WASH option is selected, the
dishwasher heats water in the main wash to
approximately 140
o
F (60
o
C).
This increase in water temperature helps the
dishwasher detergent remove food grease and
soil from dishes more effectively and aids in
improved drying performance. HI-TEMP WASH
option can be used with all cycles except RINSE
ONLY. HI-TEMP WASH is automatically provided
when the HEAVY WASH cycle is selected.
When HI-TEMP WASH option is selected, the
light above the pad will come on and remain
on until end of cycle. To turn off the HI-TEMP
WASH option, press the pad a second time.
The light above the pad will turn off.
Heat Dry
The HEAT DRY option in combination with
rinse aid will enhance drying performance.
The energy required to use the HEAT DRY
option costs pennies per cycle; however you
will have items in your dish load that will not
be completely dry at the end of the cycle.
Child Lock Controls
To prevent children from accidently changing
the dishwasher cycle or starting the
dishwasher, lock the dishwasher controls by
pressing and releasing the DRY OPTION pad
for 3 seconds while the door is latched. An
indicator light on the lock graphic pad will
illuminate when the controls are locked and
no new selections can be made until the lock
is released. To unlock the controls, press the
same pad, DRY OPTION, again for 3 seconds
until the indicator light goes out.
*Status Indicator Lights
The WASHING light comes on at the beginning
of the cycle and remains on until the end of
the main wash.
Whether heated or unheated dry is selected
the DRYING light will come on during the
drying portion of the cycle.
When the SANITIZE option is selected, the
SANITIZED light will glow when the SANITIZE
cycle is fi nished. If the dishwasher did not
properly sanitize the dishes, the light will not
come on. This can happen if the cycle is
interrupted. The light will remain on until the
door is opened.
The CLEAN light will come on at the end of
cycle and remain on until the door is opened.
*Delay Start
The DELAY START option allows you to
automatically delay starting your dishwasher
for either 2-4-6 hours.
To activate delay start option for 2-4-6 hour
delay, press the pad once for a 2 hour delay,
twice for 4 hours and three times for 6 hours.
A light will come on indicating the delay start
hours and will remain on until cycle starts.
Press the START/CANCEL pad to start the delay
option. If the delay option is interrupted, the
START/CANCEL pad will have to be pressed
again to return to delay option.
To cancel the DELAY START option and begin
the cycle before the delay period is over,
press and hold the START/CANCEL pad for 3
seconds.
To Cancel a Cycle
You can cancel a cycle anytime during the cycle.
Press and hold the START/CANCEL pad for 3
seconds. The light above the cycle and option
selected will go out, the START/CANCEL light
will remain illuminated, the dishwasher will start
a 90 second drain. At the end of the drain,
select the next desired cycle.
NOTE
If the dishwasher door is opened while the
unit is running, the START/CANCEL pad must
be pressed and the door shut immediately
to return the unit to the selected cycle and
option, this must happen within 10 minutes
for the unit to continue the cycle.
ë