Full Product Manual
Table Of Contents
- CTable of contents
- Questions?
- Product Record and Registration
- Important Safety Instructions
- Before Setting Surface Controls
- Single radiant surface elements (all models)
- 1. Place correctly sized cookware on surface element.
- 2. Push in and turn the surface control knob in either direction (Figure 12) to the desired setting (refer to the “Suggested radiant surface element settings” in Table 1).
- 3. When cooking is complete, turn the radiant surface element OFF before removing the cookware.
- Suggested radiant surface element settings
- Dual radiant surface elements (some models)
- 1. Place correctly sized cookware on the surface element.
- 2. Push in and turn the surface control knob clockwise to begin heating both the inner and outer elements. If only the inner element is needed for smaller cookware, push in and turn the knob counter-clockwise (see Figure 13).
- 3. When cooking is complete, turn the knob to OFF before removing the cookware.
- Figure 13: Dual element knob settings
- Keep warm (some models)
- 1. Push in the knob and turn in either direction (see Figure 14). The temperatures are designated by hi and lo. However, the control can be set at any position between Hi and Lo for different levels of warming.
- 2. When ready to serve, turn the control to OFF. The hot surface indicator light will remain on until the warm zone cools.
- Figure 14: Keep warm knob
- Table 2: Recommended keep warm zone settings
- Home Canning
- Single radiant surface elements (all models)
- Setting Surface Controls
- Care and Cleaning
- Before You Call
18
Solutions to Common Problems:
Before you call for service, review the following list. It may save you time and expense. Possible solutions are provided
with the problem listed.
Problem Cause / Solution
Entire appliance does not
operate.
Appliance not connected. Make sure power cord is plugged properly into outlet.
Check your fuse box or breaker box to make sure the circuit is active.
Electrical power outage. Check house lights to be sure. Call your local electric
company for service outage information.
Cooktop Problems
Surface element is too hot or not
hot enough.
Incorrect surface control setting. Adjust power level setting.
Surface element does not heat or
does not heat evenly.
Be sure the correct surface control knob is turned on for the element needed.
Cookware is light weight or warped. Use only flat, evenly balanced, medium or heavy-
weight cookware. Flat pans heat better than warped pans. Cookware materials and
weight of the material affect heating. Heavy and medium-weight pans heat evenly.
Because lightweight pans heat unevenly, foods may burn easily.
Areas of discoloration with
metallic sheen on cooktop
surface.
Mineral deposits from water and food. Remove them using cooktop cleaning creme
applied to the ceramic surface. Buff with a non-abrasive cloth or sponge.
Scratches or abrasions on
cooktop surface.
Coarse particles such as salt or hardened soils between cooktop and utensils can
cause scratches. Be sure the cooktop surface and bottoms of utensils are clean
before use. Small scratches do not affect cooking and will become less visible with
time.
Cleaning materials not recommended for ceramic-glass cooktop have been used.
Apply cooktop cleaning creme to the ceramic surface. Buff with a non-abrasive cloth
or sponge.
Cookware with a rough bottom was used. Use smooth, flat-bottomed cookware.
Metal marks on the cooktop. Sliding or scraping of metal utensils on cooktop surface. Do not slide metal utensils
on the cooktop surface. Apply cooktop cleaning creme to the ceramic surface. Buff
with a non-abrasive cloth or sponge. For more information, see
“Cooktop Mainte-
nance” on page 16.
Brown streaks or specks on
cooktop surface.
Boil overs are cooked onto the surface. When cooktop is cool, use a razor blade
scraper to remove soil. For more information see
“Cooktop Maintenance” on page 16.
BEFORE YOU CALL