Installation guide

ManualsBrandsFrigidaire ManualsCooktopOfficial Frigidaire cooktop

iNSTALLATiON AND SERVICE MUST BE PERFORMED BY A QUALiFiED iNSTALLER.

iMPORTANT: SAVE FOR LOCAL ELECTRICAL iNSPECTOR'S USE.

READ AND SAVE THESE iNSTRUCTiONS FOR FUTURE REFERENCE.

FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and liquids in

the vicinity of this or any other appliance.

Cooktop Dimensions

IMPORTANT INSTALLATION-INFORMATION

o All electric cooktops run off a single phase, three-wire

or four-wire cable, 240/208 volt, 60 hertz, AC only

electrical supply with ground.

Please note minimum distances between cooktop and

adjacent and overhead cabinetry is 30" (76.2 cm).

Cooktop Cutout Dimensions

* 30" (76.2 cm) min. for unprotected cabinet

24" (61 cm) min. for protected surface

Figure I

iiiiiiii!ii!iiililiiliil!iiiiiiiiiiiiiiiiiiiliiiiiiiiiiiiiiiiiliililliiiiii!_ii_i_!!i_ii!ii!ili_iiliii!il!iliii!iii!iiiliiliililliiliililiiiliiliiliililliiiiiiiliiii!!il!iiiiiiiiiiiiiliii!ii!iliiiiiiiiiiliiiiiiiiiiliiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_!i_iil_i,!:,:_i__:_i_:i__!i_iiiiiii_i_!__i_i_i__i__i__i_i_i__i_i_i__i__i__i_i_i__i_i_!__i_i!_i!_i_i_i:;i;i;i;i;i;i;i;i;i;i;i;i;i;i;i;i;i;i_i_!_i_i!i_!i_!i_!i_!J!i_!_i_i_!_:i_i¸iii_i_i_i_i_i_¸i_i_iiil'i!_i!_ii_ii_ii_i!_!__!_!i_ii_ii_ii_iiiiiiiiiiiiiiiiiiiliii'ii_;i_;i_;i_;i_;i_;i_;i!ii_iiiiiiiiiiiiiiill_i_!_i_i_;_i_ii___!_i_!_i_i_¸i_iiiiiiiiiiiiiiiiiiiiiiiil'i!_i!_ii_ii_ii_i!_!_!_!i_i_i_!i!i!i!i!i!i!i!i!i!i!i!i!i!i!i:ii!i_i!_i!_!_!_!,i,!_!iiiii__i!_i!_i!_i!@_i_ii_!_@i¸iiiiiiii¸ii}iiiiiiiiiiiiiiiiiiiiiiiiiiiii_iiii_¸iiiiiiiiiiiiiii'i!_i!_i!_!_!_!i_i!_i__i__i_i_i_i_i_i_ii!!i:i!_iii_iii!i_i_i_i_i_!__ii_i!}!:_i!_ii_ii_!_i!_i!_i!_i;:il:ii:ii:ii:ii:ii:ii:ii:il:ii:ii:ii:ii:ii_i_i:il_!i_i_i_!__i_i_i_i_i_i_i_i_i_i_i_ii_il_il_ii_i_i_;i_i_i_ii_:!:!:!:!i_!i_i_@__i,i_;_i_i';'i'ii_iiiiiiiiiii

///%!:!:!_!_!!i!i!i!_!!!i!i_!_!_i_!_i_!i!_!iiiiiiiiiii!ii!!i!i!i!i!iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_iiiiiiiiilililililili!i!i!i!i!i!i_i_iiii_i_i_i_ii!_!_i_i!ii_!!_i_i_i_i_i_i_!_!_!_!_!_!_!_i!i!i!_ii_ii_ii_i_@_ii_ii_ii_ii_ilililiiiii_iiiiiiiiiiiiiiiilill!ii!!ii_!_i_i_iji_ii_ii_ii_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiililililili!i!i!i!i!i!ii!i!iiiiiiiiiiiiiiii!i!,@_ii_ii_ii_ii_i!iiliiilili!iiiiiiiiiiiiiiiii!i!i!i!i!i!i_i_i!ii!!ii!_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiliiiiiii!i!i!i!i_i_i!!i!i!iiii'i'i_!i'ii'ii!ii!!ii_'i'_@i_ii_i_i_i_i_i_i_i_i_!i:iM_ii!ii!!i_i'i_!@i!!i!!i!!i!!i!!i!!_!i_!i_!i_i!_!i_i_i!_i_i3!i_!ii!!iiiillii!i!ili!i!iii'i_ii'_!i!!!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!i!!i!i_i_i_i_i_iiliiilili!i!ii!iiiiiiiiilili!i!i!i_ii'_i_!_ii!ii!i!ii!!i'i_i_ii!ii!iiiiiliiiiiiii_i_i_iiiii_}!_!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!_i!@_i_i'_!_@_!i!!i!ii!iiiiiiiiiiiiiiiiiiiiiiiiiiiiiB,i,i,!,!!_!!

26"CoilElements 253A(65.4) 219/16(54.8) 3½ (8.9) 25 (63.5) 25 (63.5) 20½ 62.1) 20½ 62.1) 5½(14)

30" Ceramk-Glass 303A(78i) 213/8 (54.3) 3Y4(8.3) 295/8(75.2) 20Y4(51.4) 20½ (52.1) 5(12.7)

30"CoilElements 30 (76.2) 21½ (54.6) 3 (7.6) 2634(67.9) 28Y4(71.8) 19I/8 (48.6) 20 (50.8) 5(12.7)

32" Ceramic-Glass 32Y4(81.9) 201A(51.4) 334(9.5) 31 (78.7) 31Y4(79.4) 19(48.3) 191A(48.9) 534(14.6)

32"CoilElements 321A(81.9) 201A(51.4) 334(9.5) 31 (78.7) 31Y4(79.4) 19(48.3) 19Y4(48.9) 5 34(14.6)

36" Ceramic-Glass 3634(93.3) 213/8 (54.3) 3Y4(8.3) 35% (90.5) 361/8(91.8) 201A(51.4) 20½ (52) 5(12.7)

36"CoilElements 36 (91.4) 18(45.7) 37/s(9.8) 34Y4(87) 343/8(87.3) 165/8(42.2) 163A(42.5) 57/8(14.9)

@6"X18"model)

36"CoilElements 36 (91.4) 21½ (54.6) 3 (7.6) 5(12.7)

(36"X211/2"model)

All dimensions are in inches (cm).

Only some models are available in Canada.

* Allow 2" (5 cm) space below cooktop to clear the electric cable and allow for installation of the junction box on the wall at the

back of the cooktop.

Printed in United States

P/N 318201426 (0810) Rev. B

English - pages 1-6

Espahol- pages 7-13

Fran_ais - pages 14-20

Summary of content (20 pages)

PAGE 1
iNSTALLATiON AND SERVICE MUST BE PERFORMED BY A QUALiFiED iNSTALLER. iMPORTANT: SAVE FOR LOCAL ELECTRICAL iNSPECTOR'S USE. READ AND SAVE THESE iNSTRUCTiONS FOR FUTURE REFERENCE. the vicinity FOR YOUR SAFETY: Do not store or use gasoline of this or any other appliance. Cooktop Dimensions or other flammable vapors and liquids in IMPORTANT INSTALLATION-INFORMATION o All electric cooktops run off a single phase, three-wire or four-wire cable, 240/208 volt, 60 hertz, AC only electrical supply with ground.
PAGE 2
Overhead Cabinet Should NotExceed aMaximum Depth of13"(33cm) 30"(76.2 cm)Min. _' Clearance Between the Top of the Cooking Platform and the Bottom of an Unprotected ,I--YT----_ , I _ -__ Wood "-J or Metal Cabinet_l _ 24" (61 cm) Min. when_ Bottom of Wood or Metal Cabinet is Protected by Not Less Than 1/8" Flame Retardant Millboard Covere_ With Not Less Than No. 28 MGS Sheet Steel, 0.015" (0.4 ram) Stainless Steel, 0.024" (0.6 mm) Aluminum or 0.020" (0.5 mm) Copper ' !1 Min.
PAGE 3
important Notes to the Installer 1. Read all instructions contained in these installation 2. 3. 4. instructions before installing the cooktop. Remove all packing material before connecting the electrical supply to the cooktop. Observe all governing codes and ordinances. Be sure to leave these instructions with the consumer. An extension appliance. Such use may result in a fire, electrical shock, or other personal injury. 2.
PAGE 4
Thisappliance isequippedwitha copperconductor flexiblecable.If connection ismadeto aluminumhouse wiring,useonlyspecialconnectors whichareapproved forjoiningcopperandaluminumwiresin accordance withthe NationalElectrical Codeandlocalcodesand ordinances. _lmproper connection of aluminum house wiring to copper leads can result in a short circuit or fire. Use only connectors designed for joining copper to aluminum, and follow the manufacturer's recommended procedure closely. .
PAGE 5
Cooktop Installation COOKTOP COUNTERTOP _- 1. All Ceramk-Glass Cooktops Visually inspect the cooktop for damage. Also make sure all cooktop screws are tight (see Figure 8). Retainer Brackets Must Be Installed At Least 1/16" (0.16 cm) BELOW Countertop NYLON SPACER RETAINER BRACKET Figure 10 . SCREWS Figure 8 Set the cooktop into the countertop cutout. NOTE: Do not use caulking compound; cooktop should be removable for service when needed.
PAGE 6
Reach down through hold down retainers top is firmly retained surface unit openings with screws as shown. to counter top. and install Be certain the four cooking To clamp down, insert bracket with offset side of angle into on each side of unit. The screw should then be run through bracket and against bottom of counter. Tighten until draws down. NYLON SPACER COOKTOP slot COOKTOP _ COUNTERTOP t;....
PAGE 7
LA INSTALACION Y EL SERVICIO DEBEN SER EFECTUADOS POR UN INSTALADOR CAUFICADO. IMPORTANTE: GUARDE ESTAS INSTRUCCIONES PARA USO DEL iNSPECTOR LOCAL DE ELECTRICIDAD. LEA Y GUARDE ESTAS INSTRUCCIONES PARA REFERENCIA FUTURA. PARA SU SEGURIDAD: No almanece ni utilice gasolina u otros vapores y liquidos inflamables en la proximidad de este o de cualquier otro artefacto. Dimensiones de la Estufa INFORMACION IMPORTANTE PARA LA INSTALACION 30" Min.
PAGE 8
Elarmario superior nodebe sobrepasar una profundidad m_ixima de13"(33cm) I--I 30" (76.2 cm) min. de espa I-I min. distancia entre la parte superior del fog6n, y la parte inferior de u.n armano de madera o metal sin protecci6n. _ I I recomendada entre el __,,, I borde trasero del corte y "---,,J___ el compartimiento de "_-combustible m_is cercano sobre la parte superior del armario 24" (61 cm) min.
PAGE 9
Notas 1. irnportantes para el instalador Lea todas las instrucciones contenidas en este manual antes de instalar la estufa. 2. Saque todo el material usado en el embalaje de la estufa antes de conectar el suministro el_ctrico a la estufa. 3. 4. Observe todos los cSdigos y reglamentos pertinentes. Deje estas instrucciones con el consumidor.
PAGE 10
Enesteelectrodomestico senecesJta uncablede puestaatierra. Cable desde el suministro de energia J-"_ Esteelectrodom_stico vieneequipado conuncablede conexiOn decobre.Siestotuvieraqueconectarse a los cablesdealuminiodeunacasa,usesolamente los conectores especiales aprobados paraempalmes decobre yaluminio, deacuerdo conelCOdigo El_ctrico Nacional y losreglamentos ycOdigos locales.
PAGE 11
No quite los espaciadores de nilon en los bordes de la estufa.
PAGE 12
PLANCHA DE COCINAR Fije la plancha de cocinar a la mesa usando tornillos para madera a travez de los huecos de las paredes verticales de la base rectangular. Si la plancha de codnar va a set instalada en una abertura existente (que no exceda las dimensiones maximas indicadas en la figura 1), deben seguirse los siguientes pasos: MOSTRADOR __T 0 RN kL0 _CAJA Figura 11 . 3. Modelos: 32" con resistendas espirales 1.
PAGE 13
Revisi6n de operad6n Consulte el Manual del Usuario para las instrucciones de funcionamiento. No toque el cristal o los elementos delaestufa. Puedequeest_nlosuficientecalientes para quemar. Ubicad6n del numero de modelo y de serie La placa con el n0mero de modelo y de serie est,1 ubicada en el fondo de la estufa o en la base rectangular del quemador y puede verse al levantar la cubierta de la unidad.
PAGE 14
UN INSTALLATEUR QUALIFll _ DOlT EFFECTUER L'INSTALLATION ET LE SERVICE. iMPORTANT: CONSERVEZ CES iNSTRUCTiONS POUR LES INSPECTEURS LOCAUX. USEZ CES iNSTRUCTiONS ET CONSERVEZ=LES POUR REFERENCES ULTERIEURES. POUR VOTRE SECURITE: N'entreposez et n'utilisez inflammables a proximit6 de cet appareil ou de tout autre appareil.
PAGE 15
L'armoire sup_rieure ne dolt pas exceder une profondeur maximale de 13" (33 cm). D6gagement minimum de30 _ (76.2 cm) entre le haut de la, surface .de cuisson et la ba_e. c,'e I armo re en bo sou en m6tal non protegee. _ ,'_Oist l ---,__ I i Jl recommand_e entre le _ebord arri_re de --_J,_.__ d_coupage et lemur _._ Minimum de 24" (61 cm)Iorsque la an_e minimale de H | I L,,_ -__J I en _'_ materiel combustible le | plus proche du dessus de -_ T 10" (25.
PAGE 16
Installateur N'utilisez 1. Lisez toutes ces instructions avant de proceder I'installation de la plaque de cuisson. 2. Enlevez tout le materiel d'emballage avant de proceder au raccordement electrique. 3. Observez tousles codes et reglements applicables. 4. Assurez-vous de laisser ces instructions au consommateur. electrique avec cette appareil. Son utilisation peut causer un feu, un choc electrique ou des blessures corporelles. 2.
PAGE 17
Cetappareilestmunid'uncableconducteur flexibleavec illsencuivre.Silaconnexion estfaitea unfilage r_sidentiel enaluminium, utilisezseulement des connecteurs sp_ciaux approuv_s pourleraccord deillsen cuivrea desillsenaluminium conform_ment aucode nationald'_lectricit_ etauxcodesetordonnances Iocaux. La connexion inappropriee d'un circuit r6sidentieJ en aluminium _ des fils en cuivre peut entrainer un court-circuit ou un feu.
PAGE 18
Installation de la plaque Les supports de fixation DOIVENT 6tre install6s conformement aux codes Iocaux ou, en leur absence, en conformite avec le National Electrical Code ANSI/ de cuisson 1. Toutes les plaques de cuisson vitroc6ramiques: V_rifiez si la plaque de cuisson est endommag@. Veillez _galement _ ce que toutes les vis de la plaque de cuisson soient bien serr@s (Figure 8). NFPA No. 70, derniere 6dition, ou le Code Electrique canadien norme ACNOR C22.1, Pattie I (Figure 10).
PAGE 19
3.ModUles de plaquedecuisson32"avec_lernents spiraux: 1.Placez I'appareildansI'ouverture du comptoiret centrezI'unit_. 2. Enlevez les_l_mentset lescuvettes. 3. UnefoisI'unit_install_edansI'ouverture, vous devezlafixertel quemontr__ lafigure12. 4. Replacez lescuvetteset les_l_ments. 5.Faiteslesraccordements #lectriques commeindiqu# lasection"Connexions #lectriques".
PAGE 20
Verification de fonctionnement R_f_rez-vous auGuide de I'utilisateur pour le mode de fonctionnement. Ne touchez pas _ la vitre de la plaque de cuisson ou aux _l_ments. IIs peuvent _tre suffisamment chauds pour causer des br01ures. Emplacement des numCros de module et de s_rie La plaque signaletique est situee sous la plaque de cuisson ou dans le boTtier.