Owner's Manual
Table Of Contents
- Table of contents
- Questions?
- Product Record and Registration
- Important Safety Instructions
- Before Setting Surface Controls
- Radiant surface elements
- 1. Place correctly sized cookware on the radiant surface element.
- 2. Push in and turn the surface control knob in either direction (Figure 4) to the desired setting (refer to the “Suggested radiant surface element settings” table, Table 1).
- 3. When cooking is complete, turn the radiant surface element OFF before removing the cookware.
- Suggested radiant surface element settings
- Home Canning
- Radiant surface elements
- Setting Surface Controls
- Before Setting Oven Controls
- 1. Press clock key.
- 2. Press in and hold or key until the correct time appears in the display. The UP arrow key will increase time and DOWN arrow key will decrease time.
- Operating oven light (some models)
- Setting bake
- Figure 7: Pan spacing suggestions
- 1. Arrange oven racks while the oven is still cool.
- 2. Turn the oven temp. control knob to the desired oven temperature (Figure 8).
- 3. Preheat the oven for 10 to 12 minutes before baking. Preheating is not necessary when roasting, cooking casseroles or broiling most foods.
- 4. When finished cooking, turn the oven temp. control knob to OFF position.
- Figure 8: Oven temperature control
- Figure 9: Rack positions
- Figure 7: Pan spacing suggestions
- Setting broil
- 1. Arrange oven racks while the oven is still cool.
- 2. Turn the oven control knob to broil. Most foods can be broiled at the broil setting. Preheat the oven if desired.
- 3. Place the insert on the broiler pan (if equipped), then place the food on the insert. Do not use the broiler pan without the insert or cover the insert with aluminum foil (Figure 11). The exposed fat could ignite.
- 4. Place the broiler pan on the oven rack. Leave the oven door open at the broil stop position when broiling (Figure 12).
- 5. Broil on one side until food is browned; turn and broil on the second side. Season and serve.
- 6. When broiling is finished, turn the oven temp control knob to OFF
- Figure 10: Be sure to set oven control to broil.
- Figure 11: Broil rack positions and broil pan insert
- Figure 12: Open door to stop position when broiling
- Setting Oven Controls
- Figure 13: Use cleaners with caution
- Surface elements and drip bowls
- Figure 14: Coil element
- 1. Lift the edge of the drip bowl across from the terminal end. Lift the surface element and drip bowl together just enough to clear the cooktop.
- 2. While holding the drip bowl and surface element, gently pull the terminal end out from terminal plug. Do not remove the hold-down clip (if equipped) from the drip bowl..
- Figure 15: Removing coil and drip bowl
- Figure 14: Coil element
- Cleaning drip bowls
- 1. Slide the terminal end on the element through the opening in the drip bowl.
- 2. Align the element support to rest on the rim inside the drip bowl. If your drip bowl is equipped with a hold-down clip, align the element support opposite the terminal end with the slot in the hold-down clip, and snap into place.
- 3. After the element is positioned in the drip bowl, line up the terminal end with the terminal plug as shown.
- 4. Hold the surface element and drip bowl together as level as possible and firmly push the terminal end into the terminal plug. Make sure element terminal is seated properly into terminal plug. Make sure the surface element is level to reduce the ha...
- Cleaning under bake element (some models)
- Cleaning under cooktop (some models) To raise the cooktop for cleaning (some models)
- Removing and Replacing the Oven Door:
- 1. Open oven door completely, horizontal with floor (See Figure 18).
- 2. Pull the door hinge locks on both left and right door hinges down from the oven frame completely towards the oven door (See Figure 19). A tool such as a small flat-blade screwdriver may be required.
- 3. Firmly grasp both sides of oven door along the door sides. Do not use the oven door handle (See Figure 20).
- 4. Close the door to approximately 10 degrees from the door frame (See Figure 20).
- 5. Lift the oven door hinge arms over the roller pins located on each side of the oven frame (See Figure 21).
- 1. Firmly grasp both sides of oven door along the door sides. Do not use the oven door handle (See Figure 20).
- 2. Holding the oven door at the same angle as the removal position, seat the hook of the hinge arm over the roller pins located on each side of the oven door frame (See Figure 20 and Figure 21). The hook of the hinge arms must be fully seated onto th...
- 3. Fully open the oven door, horizontal with floor (See Figure 18).
- 4. Push the door hinge locks up towards and into the oven frame on both left and right oven door hinges to the locked position (See Figure 19).
- 5. Close the oven door.
- Figure 18: Door hinge location
- Figure 19: Door hinge locks
- Figure 20: Holding door for removal
- Figure 21: Replacement and location of hinge arm and roller pin
- Replacing the Oven Light
- To remove and replace storage drawer (some models)
- Care and Cleaning
- Before You Call
8
IMPORTANT SAFETY INSTRUCTIONS
Do not touch a hot oven light bulb with a damp
cloth. Doing so could cause the bulb to break.
Handle halogen lights (if equipped) with paper
towels or soft gloves. Disconnect the appliance or
shut off the power to the appliance before
removing and replacing the bulb.
Important Safety Notice - The California Safe
Drinking Water and Toxic Enforcement Act
requires the governor of California to publish a list
of substances known to cause cancer, birth
defects, or other reproductive harms, and
requires businesses to warn customers of
potential exposures to such substances.