Owner's Guide
Table Of Contents
- Table of contents
- Questions?
- Product Record and Registration
- Important Safety Instructions
- Before Setting Surface Controls
- Radiant surface elements
- 1. Place correctly sized cookware on the radiant surface element.
- 2. Push in and turn the surface control knob in either direction (Figure 5) to the desired setting (refer to the “Suggested radiant surface element settings” table, Table 1).
- 3. When cooking is complete, turn the radiant surface element OFF before removing the cookware.
- Suggested radiant surface element settings
- Home Canning
- Radiant surface elements
- Setting Surface Controls
- Before Setting Oven Controls
- Figure 8: Model A
- Figure 9: Model B
- Figure 10: Model C
- Oven Control Features
- 1. Bake - Use to select Bake feature.
- 2. Broil - Use to set Broil feature.
- 3. Self Clean - (some models) Use to with arrow keys to set self clean cycle of 2 or 3hours.
- 4. Set Clock - Use with arrow keys to set the time of day.
- 5. Oven on indicator light - The oven light will glow each time the oven turns on to maintain the set oven temperature.
- 6. Preheat light - The preheat light will glow when the oven is preheating or if the desired temperature is reset higher than the actual oven temperature.
- 7. Door locked - The door locked light will flash when the oven door locks and unlocks, when the oven door lockout is active, or when the self clean cycle feature is active.
- 8. Up and Down arrows - Use with the feature or function keys to set oven temperature, Bake Time, Start Time, clean time, and setting or adjusting the clock and minute timer.
- 9. Timer on-off - Use to set or cancel the minute timer. The minute timer does not start or stop any cooking function. Timer on-off is used to set the continuous bake function.
- 10. Bake Time - Enters the length of baking time desired.
- 11. OFF - Use to clear any feature previously entered except the time of day and minute timer. Also use OFF to activate oven lockout feature. (some models)
- 12. Start Time - Use to set the desired start time for baking and self clean. May be used with Bake Time to program a delayed timed bake.
- 13. Quick Bake - Quick Bake uses a fan to circulate the oven's heat uniformly and continuously around the oven. This improved heat distribution allows for fast, even cooking and browning results.
- 14. Oven Light - Use to turn on internal light when checking on food. Also will turn on when the oven door is open.
- 15. Steam Clean (some models) - The Steam Clean feature offers a chemical free and time saving method to assist in the routine cleaning of small and light soils.
- Table 2: Minimum and maximum control settings
- 170°F (77°C)
- 550°F (288°C)
- 170°F (77°C)
- 550°F (288°C)
- LO - 400°F (205°C)
- HI - 550°F (288°C)
- 12 Hr. Mode
- 24 Hr. Mode
- 0:01 Min.
- 0:01 Min
- 11:59 Hr./Min.
- 11:59 Hr./Min.
- 12 Hr. Mode
- 24 Hr. Mode
- 1:00 Hr./Min.
- 0:00 Min
- 12:59 Hr./Min.
- 23:59 Hr./Min.
- 12 Hr. Mode
- 24 Hr. Mode
- 1:00 Hr./Min.
- 0:00 Min
- 12:59 Hr./Min.
- 23:59 Hr./Min
- 12 Hr. Mode
- 24 Hr. Mode
- 0:01 Min
- 0:01 Min
- 5:59 Hr./Min.
- 5:59 Hr./Min.
- 2 hours
- 3 hours
- Setting the Clock
- Temperature display (Fahrenheit/Celsius)
- Changing between continuous bake setting or 12- hour energy saving feature
- 1. Press and hold timer on-off for 6 seconds until a tone sounds. — — hr will appear in the display for continuous cooking. The current time of day will return to the display.
- 2. To cancel the continuous bake setting, press timer on- off and hold for 6 seconds until a tone sounds. 12 hr will appear in display indicating that the control has returned to the 12-hour energy saving feature.
- Setting a silent control panel
- Setting oven lockout (models A and C)
- 1. Press OFF and hold for 3 seconds. Loc will appear in display, the door locked indicator light will flash, and the motor driven door lock will begin to close. Allow about 15 seconds for the oven door to lock. Once the oven door is locked, the curre...
- 2. To cancel the Oven Lockout feature, press OFF and hold for 3 seconds. The control will unlock the oven door and resume normal operation.
- Operating oven light
- Setting the minute timer
- 1. Press timer on-off.
- 2. Press to increase time in one-minute increments. Press and hold to increase time in 10-minute increments. The timer can be set for any amount of time from 1 minute to 11 hours and 59 minutes.
- 3. When the set time ends, the timer will beep three times and will continue to beep three times every minute until timer on-off is pressed.
- Setting Bake
- Figure 11: Pan positions two rack baking
- 1. Press Bake. — — — appears in the display.
- 2. Within 5 seconds, press or. The display will show 350°F (177°C). The temperature can then be adjusted in 5°F (1°C) increments.
- 3. When a key is released, the oven will begin heating to the selected temperature. When the oven reaches the set temperature, the preheat indicator light will turn off and the control will beep three times.
- 4. To cancel the baking function, press OFF.
- 1. Press Bake.
- 2. Press or to increase or decrease to a new temperature. The oven indicator light on the electronic display will turn on and off when using the bake feature and during preheat. This is normal and indicates that the oven is cycling to maintain the se...
- Figure 12: Rack positions for raised bake and hidden bake ovens
- Figure 11: Pan positions two rack baking
- Setting Quick Bake (some models)
- Figure 13: Pan spacing and oven rack positions
- 1. Press Quick Bake. — — — ° appears in the display.
- 2. Within 5 seconds, press or . The display will show 350°F (177°C). The temperature can then be adjusted in 5°F (1°C) increments using the up or down arrow keys.
- 3. When a key is released, the oven will begin heating to the selected temperature.
- 4. When the oven reaches the set temperature, the preheat indicator light will turn off and the control will beep three times.
- 5. To cancel Quick Bake, press OFF.
- 1. Press Quick Bake.
- 2. Press or to increase or decrease to a new temperature. The oven indicator light on the electronic display will turn on and off when using the bake feature and during preheat. This is normal and indicates that the oven is cycling to maintain the se...
- 3. To cancel baking press OFF.
- Figure 13: Pan spacing and oven rack positions
- Setting Bake Time
- 1. Be sure the clock is set to the correct time of day.
- 2. Place the food in the oven.
- 3. Press Bake. — — — ° appears in the display.
- 4. Within 5 seconds, press or . The display will show 350°F (177°C). The temperature can then be adjusted in 5°F (1°C) increments,
- 5. Press Bake Time.0:00 will appear in the display.
- 6. Press or until the desired baking time appears in the display.
- 7. The oven will turn on and begin heating.
- 1. End will appear in the display, and the oven will shut off automatically.
- 2. The control will beep three times every 60 seconds as a reminder until OFF is pressed.
- Setting Start Time (delayed start)
- 1. Be sure that the clock displays the correct time of day.
- 2. Place food in the oven.
- 3. Press Bake. — — — ° appears in the display. Within 5 seconds, press or . The display will show 350°F (177°C). The temperature can then be adjusted in 5°F (1°C) increments.
- 4. Press Bake Time. 0:00 will appear in the display.
- 5. Press or until desired baking time appears.
- 6. Press Start Time. The time of day will appear in the display.
- 7. Press or until the desired start time appears in the display.
- 8. Once the controls are set, the control calculates the time when baking will stop. The oven will turn on at the delayed start time and begin heating.
- 1. Press the function you want to change.
- 2. Press or to adjust the setting.
- Setting Broil
- Figure 14: Rack positions
- 1. Arrange the oven rack while oven is still cool.
- 2. Press broil. — — will appear in display.
- 3. Press for HI broil or for LO broil. Most foods may be broiled at the HI broil setting. Select the LO broil setting to avoid excess browning or drying of foods that should be cooked to the well-done stage.
- 4. For optimum results, preheat broil for 2 to 5 minutes before adding food.
- 5. If using a broil pan and insert, place insert on the broil pan. Place food on the insert
- 6. Place the broiler pan and insert on the oven rack. Broil with oven door open to the broil stop position (Figure 15).
- 7. Broil on one side until food is browned. Turn and broil food on second side.
- 8. When broiling is finished press OFF.
- Figure 15: Broil pan and insert (L); Door in broil stop position (R)
- Table 3: Broil recommendations
- Figure 14: Rack positions
- Rack Position
- Temp
- 6 or 7
- HI(550°F)
- 6:00
- 5:00
- 6 or 7
- HI(550°F)
- 7:00
- 5:00
- 6 or 7
- HI(550°F)
- 8:00
- 7:00
- 6
- HI(550°F)
- 8:00
- 6:00
- 5
- LO(400°F)
- 20:00
- 10:00
- 6
- LO(400°F)
- 8:00
- 6:00
- 6
- HI(550°F)
- 13:00
- --
- 5
- HI(550°F)
- 5:00
- --
- 7
- HI(550°F)
- 6:00
- 5:00
- 7
- HI(550°F)
- 9:00
- 7:00
- 6
- HI(550°F)
- 10:00
- 8:00
- Self Clean (models A and C)
- To set a self clean cycle or a delayed start self clean cycle:
- 1. Be sure the clock displays the correct time of day.
- 2. Press Start Time. The: in the time of day will flash.
- 3. Press and hold to scroll to the time to start the delayed self clean cycle. Release the key when the desired time is displayed.
- 4. Press clean. --- appears in the display.
- 5. Press until 3:00 appears in the display for a 3 hour self clean process, or push until 2:00 appears in the display for a 2 hour self clean process.
- 6. As soon as the controls are set, the motor driven lock will begin to close automatically and the door locked indicator light will flash. Do not open the oven door while the light is flashing (allow about 15 seconds for the oven door to lock).
- 7. CLn will appear in the display during the self clean cycle, and the door locked light will glow until the self cleaning cycle is complete or cancelled and the oven temperature has cooled.
- 1. The time of day will appear in the display window, and the Self Clean indicator light and Door Locked light will continue to glow.
- 2. Once the oven has cooled down for about 1 hour and the Door Locked light has gone out, the oven door may be opened.
- 3. To avoid possible burns, use care when opening the oven door after the self cleaning cycle. Stand to the side of the oven when opening the door to allow hot air or steam to escape.
- To stop or interrupt a self clean cycle (once it has been activated):
- Steam Clean (model B)
- 1. Remove all racks and oven accessories.
- 2. Scrape or wipe loose debris and grease from the oven bottom.
- 3. Pour 1 cup of tap water onto the oven bottom.(Figure 17) Close oven door.
- Figure 17: Add 1 cup of tap water
- 4. Press steam clean.
- 5. Press either the up arrow or down arrow to activate. St Cn will appear in the display.
- 6. The oven will start automatically and the display will show the time remaining in the Steam Clean cycle. Do not open the door during this time. If door is open while in steam clean (d-O) will appear in the display.
- 7. When the steam clean cycle is complete an alert will sound and the END message will show in the display. Press OFF to return to the clock. Press OFF at any time to cancel the Steam Clean.
- 8. Take care opening the door when the steam clean is finished. Stand to the side of the oven out of the way of escaping vapor.
- 9. Wipe oven cavity and bottom. Do not clean oven door gasket (Figure 18). Avoid leaning or resting on the oven door glass while cleaning cavity.
- Figure 18: Clean around the oven door gasket
- Adjusting the oven temperature
- 1. Press Bake.
- 2. Set the temperature to 550°F (288°C) by pressing and holding .
- 3. Within 3 seconds, press and hold Bake until numeric digit(s) appear. Release Bake key. The display now indicates the amount of degrees offset between the original factory temperature setting and the current temperature setting. If the oven control...
- 4. The temperature can now be adjusted up or down 35°F (19°C), in 5°F increments. Press and hold to adjust the temperature higher until the desired amount of offset appears in the display. When lowering the oven temperature using , a minus sign (-...
- 5. When you have made the desired adjustment, press OFF to go back to the time of day display.
- Setting Oven Controls
- Figure 19: Use cleaners with caution
- Surface elements and drip bowls
- Figure 20: Coil element
- 1. Lift the edge of the drip bowl across from the terminal end. Lift the surface element and drip bowl together just enough to clear the cooktop.
- 2. While holding the drip bowl and surface element, gently pull the terminal end out from terminal plug. Do not remove the hold-down clip (if equipped) from the drip bowl..
- Figure 21: Removing coil and drip bowl
- Figure 20: Coil element
- Cleaning drip bowls
- 1. Slide the terminal end on the element through the opening in the drip bowl.
- 2. Align the element support to rest on the rim inside the drip bowl. If your drip bowl is equipped with a hold-down clip, align the element support opposite the terminal end with the slot in the hold-down clip, and snap into place.
- 3. After the element is positioned in the drip bowl, line up the terminal end with the terminal plug as shown.
- 4. Hold the surface element and drip bowl together as level as possible and firmly push the terminal end into the terminal plug. Make sure element terminal is seated properly into terminal plug. Make sure the surface element is level to reduce the ha...
- Cleaning under bake element (some models)
- Cleaning under cooktop (some models) To raise the cooktop for cleaning (some models)
- Removing and Replacing the Oven Door:
- 1. Open oven door completely, horizontal with floor (See Figure 24).
- 2. Pull the door hinge locks on both left and right door hinges down from the oven frame completely towards the oven door (See Figure 25). A tool such as a small flat-blade screwdriver may be required.
- 3. Firmly grasp both sides of oven door along the door sides. Do not use the oven door handle (See Figure 26).
- 4. Close the door to approximately 10 degrees from the door frame (See Figure 26).
- 5. Lift the oven door hinge arms over the roller pins located on each side of the oven frame (See Figure 27).
- 1. Firmly grasp both sides of oven door along the door sides. Do not use the oven door handle (See Figure 26).
- 2. Holding the oven door at the same angle as the removal position, seat the hook of the hinge arm over the roller pins located on each side of the oven door frame (See Figure 26 and Figure 27). The hook of the hinge arms must be fully seated onto th...
- 3. Fully open the oven door, horizontal with floor (See Figure 24).
- 4. Push the door hinge locks up towards and into the oven frame on both left and right oven door hinges to the locked position (See Figure 25).
- 5. Close the oven door.
- Figure 24: Door hinge location
- Figure 25: Door hinge locks
- Figure 26: Holding door for removal
- Figure 27: Replacement and location of hinge arm and roller pin
- Replacing the Oven Light
- 1. Turn electrical power off at the main source or unplug the appliance.
- 2. Remove the interior oven light shield after removing the wire holder by carefully moving the wire to the side of the glass shield. The tension from the wire holds the glass shield in place.
- 3. Pull the shield straight out. Do not twist or turn.
- 4. Replace the bulb with a new appliance bulb.
- 5. Replace the glass oven light shield. Replace wire holder.
- 6. Turn the power back on again at the main source (or plug the appliance back in).
- 7. Be sure to reset the time of day on the clock.
- Figure 28: Oven light protected by glass shield
- To remove and replace storage drawer (some models)
- Care and Cleaning
- Before You Call
