Aftermarket Installation Information

ManualsBrandsFrigidaire ManualsRefrigeration30 Inch Top Freezer Refrigerator with 18.3 Cu. Ft. Capacity, Adjustable Glass Shelving, Crisper Drawers, Auto-Close Doors, EvenTemp™ Cooling, UL Listed, ADA Compliant, and Energy Star Certified: Black

AUTOMATIC ICE MAKER

INSTALLATION INSTRUCTIONS

P/N: A13109105

WARNING

• To avoid electric shock, which can cause death or severe personal injury, disconnect the refrigerator

from electrical power before connecting a water supply line to the refrigerator.

• Connect the ice maker to a potable water supply only.

An authorized service technician is recommended to install the ice maker kit.

Ice Maker (IM117000) Kit Components

5304520536

Ice Maker

QTY: 1

5304525288

Shoulder Screw

QTY: 5

5304520538/5304520539

Cover with Door

QTY: 1

5304520535

Ice Bin

QTY: 1

5304520537

Bracket (30" only)

QTY: 1

Parts needed for install inside the unit

Tools Needed:

• Flat head screw driver • Phillips or Quadrex driver

• ¼" Hex driver • Gloves

• Drill • Needle nose pliers

Parts needed for install on back side of the unit



NOTE

Check with your local building authority for recommendations on water lines and associated materials

prior to installing your new refrigerator. For household water line hookup from the home water supply

system to the unit, Frigidaire recommends for homes with existing valves its Smart Choice

water line kit

5304437642 (with a 6� Stainless Steel Water Line) and for homes without an existing valve, Frigidaire

recommends its Smart Choice

water line kit 5304493869 (with a 6� Polyline Waterline). Please refer to

www.frigidaire.com for more information.

5304520540

Water Valve

QTY: 1

218976923

Tube

QTY: 1

241500304

#8 screw

QTY: 2

218515401

Hose and

Harness Clip

(30" only)

QTY: 3

5304455846

Clamp ¼"

QTY: 1

5303001193

Clamp ½"

QTY: 1

Summary of content (8 pages)

PAGE 1
AUTOMATIC ICE MAKER INSTALLATION INSTRUCTIONS An authorized service technician is recommended to install the ice maker kit. WARNING • To avoid electric shock, which can cause death or severe personal injury, disconnect the refrigerator from electrical power before connecting a water supply line to the refrigerator. • Connect the ice maker to a potable water supply only.
PAGE 2
Ice Maker Installation Instructions 5. For a 30" wide refrigerator install the bracket onto the ice maker. The Ice maker will slide onto the mounting features on the bracket and snap into place. The locking feature is located on the rear of the ice maker. 1. Unplug refrigerator from electrical outlet. 2. Lift the freezer shelf up and out. Set aside. 2 1 Locking Feature 3.
PAGE 3
Ice Maker Installation Instructions 7. Install the plastic shutter into the window in the front of the cover. The shutter snaps into the clips on inside face of the cover, no tools are required. Slide the ice maker cover onto the shoulder screws on top of the unit until it locks into place with a snap. 10. Install the water line by screwing the nut on the end of the tube onto the water inlet. Tighten the nut until snug, and then tighten an additional ¼ turn with needle nose pliers. (See A.) 11.
PAGE 4
Ice Maker Installation Instructions (with access cover) 15. Plug connector on water valve wire harness into the connector above the condenser coil. Install the water valve clip at the bottom right side of the unit, and route and attach the water valve harness into the clip. CAUTION Wear gloves and use extreme CAUTION when handling the access cover. 12. Remove 8 screws from access cover located at the bottom rear outside of the unit. Set aside. 16.
PAGE 5
Ice Maker Installation Instructions (without access cover) 20. Connect the valve wire harness with the white connector from the unit. Insert the wiring in the box as shown. Close the box cover completely, ensuring all wiring is inside. 18. Remove the connector box from the unit with a Philips screwdriver. Discard screw. 21. Plug the green water tube from the icemaker into the bottom outlet of the water valve. The tube should be pushed into the valve up to the black line marked on the tube. 19.
PAGE 6
Connecting Ice Maker to Water Supply Before Installing The Water Supply Line, You Will Need: • Basic Tools: adjustable wrench, flat-blade screwdriver, and Phillips screwdriver • Access to a household cold water line with water pressure between 30 and 100 psi. • A water supply line preferably made of Braided Stainless Steel or Braided Poly with integral fittings for connection to the refrigerator and the valve at the wall.
PAGE 7
Connecting Ice Maker to Water Supply To Connect Water Supply Line To Ice Maker Inlet Valve 1. Disconnect refrigerator from an electrical power source. 2. Place the end of water supply line into the sink or a bucket. Turn ON the water supply and flush the supply line until the water is clear. Turn OFF the water supply at the shutoff valve. 3. Remove the plastic cap from water valve inlet and discard the cap. 4.
PAGE 8
Ice Service If your refrigerator has an automatic ice maker, minimal ice will be produced during the first 24 hours of operation. Air in new plumbing lines may cause the ice maker to cycle 2 or 3 times before making a full tray of ice. With no usage, it will take approximately 1 to 2 days to fill the ice bin. IMPORTANT To ensure proper function for your ice maker, hook up water supply immediately or turn ice maker OFF.