Wiring Diagram

NOTICE - This service data sheet is intended for use by persons having electrical
and mechanical training and a level of knowledge of these subjects generally
considered acceptable in the appliance repair trade. The manufacturer cannot
be responsible nor assume any liability for injury or damage of any kind arising
from the use of this data sheet.
SAFE SERVICING PRACTICES
To avoid the possibility of personal injury and/or property damage, it is important
that safe servicing practices be observed. The following are examples, but without
limitation, of such practices.
1. Before servicing or moving an appliance remove power cord from electrical outlet,
trip circuit breaker to OFF, or remove fuse.
2. Never interfere with the proper installation of any safety device.
IMPORTANT
DO NOT REMOVE THIS BAG
OR DESTROY THE CONTENTS
WIRING DIAGRAMS AND SERVICE
INFORMATION ENCLOSED
REPLACE CONTENTS IN BAG
p/n A00498606 Rev B (1709)
3. GROUNDING: The standard color coding for safety ground wires is GREEN or
GREEN WITH YELLOW STRIPES. Ground leads are not to be used as current
carrying conductors. It is extremely important that the service technician
reestablish all safety grounds prior to completion of service. Failure to do
so will create a potential safety hazard.
4. Prior to returning the product to service, ensure that:
• All electric connections are correct and secure.
• All electrical leads are properly dressed and secured away from sharp edges,
high-temperature components, and moving parts.
• All uninsulated electrical terminals, connectors, heaters, etc. are adequately
spaced away from all metal parts and panels.
• All safety grounds (both internal and external) are correctly and securely
reassembled.
Indicated % Power Notes
0 0 Off
1 3 Keep Warm
2 6 Low
3 10 Medium Low
4 15 Medium Low
5 20 Medium
6 30 Medium
7 45 Medium High
8 65 Medium High
9 100 High
P >140 Power Boil
Electronic Surface Element Control (ESEC)
This cooktop is equipped with an Electronic Surface Element
Control (ESEC), which precisely controls the smoothtop cooking
elements at multiple settings. For the user, the elements are
operated by the electronic slider controls. The control settings are
shown in single-digit displays.
Hot Surface display message - If any of the induction elements
are hot, the hot surface message (H) will display and remain ON
until the cooktop cools.
Replacing an induction element
Whenever replacing any induction element, use only the screws
supplied with the range to secure the element to the mounting
panel. Never use any other type of screw to attach the induction
element.
* Please note: Electronic boards are very sensitive to static elec-
tricity. Static electricity can permanently damage electronic boards.
Before handling these parts, be sure to drain static electricity from
your body by properly grounding yourself.
BC3 TO USER INTERFACE BOARD
Á PLAQUETTE D'INTERFACE DE UTILISATEUR
THERMAL CUT-OUT
COUPE-CIRCUIT THERMIQUE
GENERATOR BOARD-LEFT SIDE
CARTE GENERATEUR-COTE GAUCHE
GENERATOR BOARD-CENTER
CARTE GENERATEUR-CENTRE
BC3
B81 BC4 B71
TAB1 TAB2
BC1
TAB102 TAB101
BC5
BPL2 BPL1 BPN1 BPN2
BPE03
BC3 B81 BC4 B71
TAB1 TAB2
BC1
TAB102 TAB101
BC5
BPL2 BPL1 BPN1 BPN2
BPE03
THERMAL CUT-OUT
COUPE-CIRCUIT THERMIQUE
THERMAL CUT-OUT
COUPE-CIRCUIT THERMIQUE
GENERATOR BOARD-RIGHT SIDE
CARTE GENERATEUR-COTE DROIT
BC3
B81 BC4 B71
TAB1 TAB2
BC1
TAB102 TAB101
BC5
BPL2 BPL1 BPN1 BPN2
BPE03
ID JUMPER: ADDRESS
1
CONNECT
BLACK JUMPER TO BC1 AND BC5
IDENTIFICATEUR: ADRESSE
2
BRANCHER BC1
ID JUMPER: ADDRESS
2
DO NOT CONNECT
BC1
IDENTIFICATEUR: ADRESSE
2
NE PAS BRANCHE BC1
ID JUMPER: ADDRESS
3
CONNECT RED JUMPER TO
BC1
IDENTIFICATEUR: ADRESSE
2
BRANCHE EN UTILISANT
FAISCEAU-FIL ROUGE
BC1
BP03
BP03
BP03
SERVICE DATA SHEET
36” BASELINE INDUCTION COOKTOP
Modular Control Systems
This appliance is equipped with a modular system of controls. The modular
system consists of various boards which communicate with one another to drive
cooking functions. Oven functions, if available, operate through an oven user
interface (UI or UIB) and an oven relay board. Cooktop functions, if available,
operate through a cooktop UI/UIB and a cooktop relay board. There may be addi-
tional boards which work within the system to drive specic functions (refer to the
schematics and diagrams and this sheet). Low voltage operating and communica-
tions power for the modular boards is provided through the wiring schemes. The
boards that generate low voltage operating and communications power depend
upon the individual control system (refer to the schematics and diagrams on
this sheet). These voltages are only the operational voltages. Do not use these
voltages as conrmation of communication between the boards. Communication
occurs through software programming on each board. This communication is not
detectable by volt ohmmeters. The programming is self-monitored and the UI
displays will show error codes based on detected failures. The individual boards
are not eld repairable. See the schematics and diagrams included on this sheet
for more unit-specic details.