Wiring Diagram

2
WASHER DIAGNOSTIC MODE
DIAGNOSTIC ID PROGRAM TEST/ACTIVATED COMPONENT TEST DESCRIPTION
1 Rinse & Spin LED Test, Button Test LEDs illuminate in sequence. Manually test buttons for tone.
2 Soak Lid Lock, Hot Valve and Clutch
Lid Locks. Fill water via HOT valve to 140mm. Disengage
the clutch.
3 Light Soil Lid Lock, Cold Valve, and Clutch
Lid Locks. Fill water via COLD valve to 140mm. Disengage
the clutch.
4 Colors
Lid Lock, Hot valve, Cold Valve, Clutch,
and Motor
Lid locks. Fill water via HOT and COLD valves to 20mm.
Agitate for 4 mins.
5 Heavy Soil Balance Switch
Out of balance switch test. Move the drum against the tilt
switch 2 times in 10 seconds. If tilt switch is working, the
WASHER RED LED, Close Washer Lid LED and Balance
Load LED will be ON simultaneously.
6 Bulky Lid lock, Drain Pump, and Clutch
Lid locks. Drain water until empty. Engage and disengage
the clutch 1 time.
7 Normal
Lid Lock, Pressure Sensor, Motor, and
Drain Pump
Lid locks. Spin for 25 seconds while draining water from
tub.
8 Activewear Lid lock, Hot Valve, and Cold Valve
Lid Locks. Fill water using both HOT and COLD valve for 5
mins. Complete test 6 or 7 to drain water from the tub.
9 Delicates — — — —
10 Quick Wash Error code history
Check last 3 error codes
• If START|PAUSE LEDs are not blinking there is no error.
• If START|PAUSE LEDs are blinking refer to Washer
Error Code Table.
Reset Washer Error Code History in Diagnostic Mode:
Rotate the washer cycle selector knob to the Quick Wash position (position 10) and press and hold Wash Temp and CANCEL buttons
simultaneously until UI stops displaying error code.
Washer Diagnostic Mode Tests
All tests should be performed with an empty tub. Any items left in the tub will cause a serious out-of-balance situation and potential
damage to the washer as it reaches higher spin speeds.
Error
Code
Error Description Display
Notication
Next Step
E42 Door lock device failure No Refer to test (6)
Looking at the Washer Error Code Table on the following page, E42 refers to a Door Lock Error.
Understanding Error Codes
In Washer Diagnostic Mode, error codes are indicated by a pattern of blinking RED and GREEN LEDs above the WASHER START|PAUSE
button. The LEDs will blink rst RED then GREEN, to provide the two digit error code number. These blinking lights can then be translated
into error codes that are listed in the chart on the following page and can help pinpoint the problem with the washing machine. The number
of times a light blinks corresponds with the digit or character it represents. Blinking 1 through 9 times will represent the corresponding digit.
Blinking 10 times =A, 11=B, 12=C, 13=D, 14=E, 15=F.
E 4 2
This letter “E” designates
that this is an Error Code.
The rst digit is the area of error. This digit
is determined by counting how many times
the LED over the START|PAUSE button
blinks RED. In this example the LED will
blink RED four times.
The second digit is the type of error.
This digit is determined by count-
ing how many times the LED over
the START|PAUSE button blinks
GREEN.
If your washing machine has multiple errors, the display will communicate up to three error codes.
• The GREEN LED light for Done will be illuminated while the rst error code is being communicated.
• The GREEN LED light for Spinning will be illuminated while the second error code is being communicated.
• The GREEN LED light for Rinsing will be illuminated while the third error code is being communicated.
START | PAUSE
Hot
Warm
Cold
Max Fill
Med
Low
Close Lid
Unbalanced
Washing
Rinsing
Spinning
Done
START | PAUSE
Close Door
Clean Lint
Drying
Cooling
Done
High
Normal
Low
An Error Code looks like this:
3
2
1