Wiring Diagram

6
DRYER DIAGNOSTIC MODE
Diagnostic Mode Tests
All tests should be performed with an empty tub. Programs not shown do not have associated tests.
Entering Diagnostic Mode:
1. Power OFF the unit by either turning the DRYER cycle selector
knob to the CYCLES position (8 o’clock position) or unplugging
the unit.
2. Turn ON the unit.
3. Within 10 seconds of powering up, rotate the knob to the
Quick Dry position.
4. Press and hold DRY Temp and CANCEL buttons simultaneously
until a beep is heard and LED lights start to blink one by one.
5. Press the START|PAUSE button.
Dryer Diagnostic Mode
Reset Dryer Error Code History in Diagnostic Mode:
Rotate the dryer cycle selector knob to the 15’ position (position 10) and press and hold Dry Temp and CANCEL buttons simultaneously
until UI stops displaying error code.
DIAGNOSTIC
ID
PROGRAM
TEST/ACTIVATED
COMPONENT
TEST DESCRIPTION
1 Quick dry Lights/ Buttons test LEDs illuminate in sequence. Manually test buttons for tone.
2 Delicates Motor Motor is driven for 10 mins
3 Activewear Motor, Heater and Thermistor Motor and Heater is driven for 10 mins.
4 Normal — — — —
5 Bulky — — — —
6 Air Fluff — — — —
7 90’ — — — —
8 60’ — — — —
9 30’ — — — —
10 15’ Error code history
Check last 3 error codes
• If START|PAUSE LEDs are not blinking there is no error.
• If START|PAUSE LEDs are blinking refer to Dryer Error Codes Table.
Looking at the Dryer Error Code Table on the following page, E42 refers to a Door Lock Error.
Understanding Error Codes
In Dryer Diagnostic Mode, error codes are indicated by a pattern of blinking RED and GREEN LEDs above the DRYER START|PAUSE but-
ton. The LEDs will blink rst RED then GREEN, to provide the two digit error code number. These blinking lights can then be translated into
error codes that are listed in the chart on the following page and can help pinpoint the problem with the dryer. The number of times a light
blinks corresponds with the digit or character it represents. Blinking 1 through 9 times will represent the corresponding digit. Blinking 10
times =A, 11=B, 12=C, 13=D, 14=E, 15=F.
E 4 2
This letter “E” designates
that this is an Error Code.
The rst digit is the area of error. This digit is de-
termined by counting how many times the LED
over the START|PAUSE button blinks RED. In
this example the LED will blink RED four times.
The second digit is the type of error.
This digit is determined by counting
how many times the LED over the
START|PAUSE button blinks GREEN.
An Error Code looks like this:
Error
Code
Error Description Possible Causes
E42 Door closed sensing error Door switch or wiring or sensing circuit on main board failure

NOTE
The unit will automatically exit Diagnostic Mode and return to
normal functionality if left unattended in diagnostic Mode for
more than 15 minutes.
Exiting Diagnostic Mode:
To exit Diagnostic Mode and return to normal function, either press
and hold the Dry Temp and CANCEL buttons simultaneously until
the LED lights stop blinking or unplug the unit for a 10 full seconds
before plugging the unit back in.
If your dryer has multiple errors, the display will communicate up to three error codes.
• The GREEN LED light for Done will be illuminated while the rst error code is being communicated.
• The GREEN LED light for Cooling will be illuminated while the second error code is being communicated.
• The GREEN LED light for Drying will be illuminated while the third error code is being communicated.
START | PAUSE
Hot
Warm
Cold
Max Fill
Med
Low
Close Lid
Unbalanced
Washing
Rinsing
Spinning
Done
START | PAUSE
Close Door
Clean Lint
Drying
Cooling
Done
High
Normal
Low

NOTE
If the dryer door has been opened and closed, the START|PAUSE
button must be pressed to activate the motor and heater.