Installation Sheet

ManualsBrandsFrigidaire ManualsAppliance Parts & AccessoriesMicrowave Trim Kit

Installation Instructions

Installation

Instructions

Built-in Trim Kit

Model # FFMOTK27LW FFMOTK27LB FFMOTK27LS

FFMOTK30LW FFMOTK30LB FFMOTK30LS

BEFORE YOU BEGIN

•

IMPORTANT – Save these instructions

for local inspector's use.

•

IMPORTANT – Observe all governing

codes and coordinates.

•

Note to Installer – Be sure to leave

these instructions with the Consumer.

•

Note to Consumer – Keep these

instructions for future reference.

• Skill level - Installation of this appliance

requires basic mechanical and electrical

skills

Read these instructions completely and carefully.

• Proper installation is the responsibility of the

installer.

• Product failure due to improper installation is

not covered under the Warranty.

• Unplug the microwave oven before

attempting installation of this kit.

• Because the kit includes metal parts, caution

should be used in handling and installation to

avoid the possibility of injury.

• Do not remove permanently affixed labels,

warnings, or plates from the product. This

may void the warranty.

FOR YOUR SAFETY:

WARNING – Before beginning the installation,

switch power off at service panel and lock the

service disconnecting means to prevent power from

being switched on accidentally. When the service

disconnecting means cannot be locked, securely

fasten a prominent warning device, such as a tag, to

the service panel.

IMPORTANT - PLEASE READ

AND FOLLOW

THIS BUILT-IN KIT IS DESIGNED FOR USE

ONLY WITH ELECTROLUX MICROWAVE

OVENS SPECIFYING BUILT-IN KIT

FFMOTK27LW/B/S OR

FFMOTK30LW/B/S ON THE RATING LABEL ON THE

LEFT SIDE WALL OF THE MICROWAVE OVEN

CAVITY.

QUESTIONS?

For customers in the United States call:1-1800-944-9044

For customers in Canada call: 1-800-265-8352 (English)

1-800-668-4606 ext.8199 (French)

Visit our Website at: www.frigidaire.com

READ CAREFULLY.

KEEP THESE INSTRUCTIONS.

PN: 316910002

October

2010

Summary of content (5 pages)

PAGE 1
Installation Instructions Installation Built-in Trim Kit Instructions Model # FFMOTK27LW FFMOTK27LB FFMOTK27LS FFMOTK30LW FFMOTK30LB FFMOTK30LS BEFORE YOU BEGIN • • Read these instructions completely and carefully. IMPORTANT – Save these instructions • for local inspector's use. • IMPORTANT – Observe all governing codes and coordinates. • • • • Note to Installer – Be sure to leave these instructions with the Consumer. • Note to Consumer – Keep these instructions for future reference.
PAGE 2
Installation Instructions PARTS INCLUDED IN THE KIT 1. Front Frame Assembly- QTY 1 2. Exhaust Duct - QTY 1 3. Bottom Mounting Rail– QTY 2 3. Screw A - QTY 11 4. Screw B - QTY 4 CHOOSING A LOCATION FOR YOUR MICROWAVE OVEN IF BUILT-IN Built-In Trim Kit allows for the installation of microwaves listed below to be built into a cabinet or wall by itself or over an electric wall oven*.
PAGE 3
Installation Instructions Screw A Center Line Illustration 2 Illustration 3 ELECTRICAL OUTLET LOCATION EXHAUST DUCT ASSEMBLY Outlet should NOT be in the shaded area as indicated on Illustration 2 1. Draw a Central Line on floor. Place the Exhaust Duct in the opening，When the Exhaust Duct Assembly is in the opening correctly, the Center Line is in the middle of the Exhaust Duct Assembly. See Illustration 3. 2. Secure the Exhaust Duct Assembly with the three screws A.
PAGE 4
Installation Instructions Bottom Mounting Rail OVEN INSTALLATION 1. Turn microwave wave upside down so you are looking at oven bottom. Secure the bottom Mounting Rail on oven with four SCREWS A. See Illustration 4 below. 2. Secure the Exhaust Duct Assembly with the four screws A.--Place the bracket on proper location where hole to hole with the oven, then put the screw inside, and screw them up. 1. Place the oven adjacent to the wall or cabinet opening. Plug the power cord into the electrical outlet. 2.
PAGE 5
Installation Instructions 1. 2. Position the FRAME ASSEMBLY to be square with the oven. Carefully place the FRAME ASSEMBLY on the oven. See Illustration 6. Check that it is level and then secure with two SCREWS B. Secure the bottom portion of the FRAME ASSEMBLY with the two remaining SCREWS B. See Illustration 7.