Installation Instructions Questions? Call 1-800-944-9044(US) 1-800-265-8352(Canada) Over the Range Microwave Oven or Visit our Website at: KWWS ZZZ IULJLGDLUH FRP BEFORE YOU BEGIN Read these instructions completely and carefully. IMPORTANT – • Save these instructions for local inspector’s use. • IMPORTANT – Observe all governing codes and ordinances. • Note to Installer – Be sure to leave these instructions with the Consumer. Note to Consumer – Keep these instructions for future reference.
Installation Instructions CONTENTS Adapting Microwave Blower for Outside Back Exhaust................17– 18 General information Mount the Microwave Oven ................19 Important Safety Instructions .................................. 3 C Electrical Requirements .......................................... 3 Recirculating ........................................ 20 – 22 Attach Mounting Plate to Wall ............20 Damage – Shipment/Installation..............................
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS You should have the wall receptacle and circuit checked by a qualified electrician to make sure the receptacle is properly grounded. This product requires a three-prong grounded outlet. The installer must perform a ground continuity check on the power outlet box before beginning the installation to insure that the outlet box is properly grounded.
Installation Instructions PARTS INCLUDED DAMAGE—SHIPMENT/ INSTALLATION (CONT.) ADDITIONAL PARTS • If the unit is damaged in shipment, return the PART unit to the store in which it was bought for repair or replacement. • If the unit is damaged by the customer, repair or replacement is the responsibility of the customer. • If the unit is damaged by the installer (if other than the customer), repair or replacement must be made by arrangement between customer and installer.
Installation Instructions TOOLS YOU WILL NEED Ruler or tape measure and straight edge Pencil # 1 Phillips screwdriver Tin snips (for cutting damper, if required) Scissors (to cut template, if necessary) Electric drill with 3⁄16“, 1⁄2“ and 5⁄8“ drill bits Carpenter square (optional) Filler blocks or scrap wood pieces, if needed for top cabinet spacing (used on recessed bottom cabinet installations only) Gloves Saw (saber, hole or keyhole) Stud finder or Safety goggles Level Hammer (optional) Duc
Installation Instructions 1 PLACEMENT OF THE MOUNTING PLATE A. REMOVING THE MICROWAVE OVEN FROM THE CARTON/ REMOVING THE MOUNTING PLATE B. FINDING THE WALL STUDS 1 Remove the installation instructions, filters, glass tray and the small hardware bag. Do not remove the Styrofoam protecting the front of the oven. Wall Studs 2 Fold back all 4 carton flaps fully against carton sides. Then carefully roll the oven and carton over onto the top side. The oven should be resting in the Styrofoam.
Installation Instructions C. DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET Plate position—beneath framed recessed cabinet bottom Plate position—beneath flat bottom cabinet Mounting Plate Tabs Touching the Cabinet Bottom Mounting Plate Tabs Touching the Back Frame 30w (76.2 cm) to Cooktop At least 30w (76.2 cm), up to 36w (91.4 cm) Plate position—beneath recessed bottom cabinet with front overhang Your cabinets may have decorative trim that interferes with the microwave installation.
Installation Instructions D. ALIGNING THE WALL PLATE Hole B Hole A Centerline Notches CAUTION: Wear gloves to avoid cutting fingers on sharp edges. Draw a Vertical Line on Wall from Center of Top Cabinet Hole D Hole C Area E NOTE: If neither C nor D is in a stud, find a stud somewhere in area E and draw a fifth circle to line up with the stud. It is important to use at least one wood screw mounted firmly in a stud to support the weight of the microwave.
Installation Instructions 2 INSTALLATION TYPES (Choose A, B or C) This microwave oven is designed for adaptation to the following three types of ventilation: A. Outside Top Exhaust (Vertical Duct) B. Outside Back Exhaust (Horizontal Duct) C. Recirculating (Non-Vented Ductless) A NOTE: This microwave is shipped assembled for Recirculating. Select the type of ventilation required for your installation and proceed to that section.
Installation Instructions INSTALLATION INSTRUCTIONS FOR EXTERNAL EXHAUST DUCTING Maximum duct length: NOTE: If you need to install ducts, note that the total duct length of 31⁄4” x 10” (8.2 x 25.4 cm) rectangular or 5” (10.5 cm) diameter/ 6” (15.2 cm) diameter round duct should not exceed 120 equivalent feet (36.5 m). Outside ventilation requires a EXTERNAL EXHAUST DUCT.Read the following carefully.
Installation Instructions EXTERNAL EXHAUST DUCTING NOTE: Read these next two pages only if you plan to vent your exhaust to the outside. If you plan to recirculate the air back into the room, proceed to page 20. OUTSIDE TOP EXHAUST (EXAMPLE ONLY) The following chart describes an example of one possible ductwork installation. EQUIVALENT LENGTH x NUMBER USED = EQUIVALENT LENGTH Roof Cap 24 Ft. (7.3 m) x (1) = 24 Ft. (7.3 m) 12 Ft. (3.6 m) Straight Duct (6”/15.2 cm Round) 12 Ft. (3.
Installation Instructions A OUTSIDE TOP EXHAUST (Vertical Duct) INSTALLATION OVERVIEW A1. Attach Mounting Plate to Wall A2. Prepare Top Cabinet A3. Adapting Microwave Blower for Outside Top Exhaust A4. Check Damper Operation A5. Mount Microwave Oven A6. Adjust Exhaust Adaptor A7. Connect Ductwork IMPORTANT NOTES: • Make sure the screws for the blower motor and blower plate are securely tightened when they are reinstalled. This will help to prevent excessive vibration.
Installation Instructions A2. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET 2 Carefully pull out the blower unit. The wires will extend far enough to allow you to adjust the blower unit. End B You need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adaptor. End A Back of Microwave 3 Roll the blower unit 90° so that fan blade openings are facing out the top of the microwave.
Installation Instructions A3. A5. MOUNT THE MICROWAVE OVEN ADAPTING MICROWAVE BLOWER FOR OUTSIDE TOP EXHAUST 5 Secure blower unit to microwave with the screw removed in Step 1. Make sure the screw is tight. 6 Replace blower plate with the screw removed in Step 1. Make sure the screw is tight. FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN. IMPORTANT: Do not grip or use handle during installation.
Installation Instructions A5. MOUNT THE MICROWAVE OVEN (cont.) A6. ADJUST THE EXHAUST ADAPTOR Open the top cabinet and adjust the exhaust adaptor to connect to the house duct. Cabinet Front Cabinet Bottom Shelf Filler Block Blower Plate Back of Microwave Damper Equivalent to Depth of Cabinet Recess Self-Aligning Screw For Front-to-Back or Side-to-Side Adjustment, Slide the Exhaust Adaptor as Needed Microwave Oven Top 4 Attach the microwave oven to the top cabinet.
Installation Instructions B OUTSIDE BACK EXHAUST (Horizontal Duct) INSTALLATION OVERVIEW B1. Prepare Rear Wall B2. Remove Blower Plate B3. Attach Mounting Plate to Wall B4. Prepare Top Cabinet B5. Adjust Blower B6. Mount the Microwave Oven IMPORTANT NOTES: • Make sure the screws for the blower motor and blower plate are securely tightened when they are reinstalled. This will help to prevent excessive vibration.
Installation Instructions B3. ATTACH THE MOUNTING PLATE TO THE WALL B4. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws and a hole large enough for the power cord to fit through. Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach the plate to a wall stud. 1 Remove the toggle wings from the bolts.
Installation Instructions 7 Place the blower unit back into the opening. B5. ADAPTING MICROWAVE BLOWER FOR OUTSIDE BACK EXHAUST (cont.) AFTER: Fan Blade Openings Facing Back End A 3 Roll the blower unit 90° Before Rotation After Rotation End B CAUTION: Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched, and that they are properly secured. Back of Microwave Back of Microwave NOTE: The blower unit exhaust openings should match exhaust openings on rear of microwave oven.
Installation Instructions Cabinet Front B6. MOUNT THE MICROWAVE OVEN Cabinet Bottom Shelf Filler Block Equivalent to Depth of Cabinet Recess Self-Aligning Screw FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN. Microwave Oven Top 4 Attach the microwave oven to the top cabinet. IMPORTANT: Do not grip or use handle during installation. 5 Insert 2 self-aligning screws through outer top cabinet holes. Turn two full turns on each screw.
Installation Instructions C RECIRCULATING (Non-Vented Ductless) INSTALLATION OVERVIEW C1. Attach Mounting Plate to Wall C2. Prepare Top Cabinet C3. Check Blower Plate C4. Mount the Microwave Oven C5. Install or change Charcoal Filter IMPORTANT NOTES: • Make sure the screws for the blower motor and blower plate are securely tightened when they are reinstalled. This will help to prevent excessive vibration.
Installation Instructions C3. CHECK BLOWER PLATE NOTE: When mounting the microwave oven, thread power cord through hole in bottom of top cabinet. Keep it tight throughout Steps 1–3. Do not pinch cord or lift oven by pulling cord. Blower Plate • • 1 Lift microwave, tilt it forward, and hook slots at back bottom edge onto four lower tabs of mounting plate. Place the microwave in its upright position, with the top of the unit facing up.
Installation Instructions C4. MOUNT THE MICROWAVE OVEN (cont.) C5. INSTALLING OR CHANGE THE CHARCOAL FILTER 5 Insert 2 self-aligning screws through outer top cabinet holes. Turn two full turns on each screw. NOTE: The charcoal filter is factory installed in recirculating models. Follow these steps to replace a filter or to install a filter after converting a vented model to recirculating operation. 1 Remove screws on top of grille using a #1 Phillips screwdriver. 2 Open the door. 3 Remove the grille.
Installation Instructions BEFORE YOU USE YOUR MICROWAVE 1. Make sure the microwave oven has been installed according to instructions. 6. RE & CA E S U UAL MAN N LATIO S L A T INS UCTION R INST 2. 7. Remove all packing material from the microwave oven. 3. Install turntable ring and glass tray in cavity 4. Replace house fuse or turn breaker back on. KEEP INSTALLATION INSTRUCTIONS FOR THE LOCAL INSPECTOR’S USE. N ATIO L L A INST UCTIONS R INST . 8. 5. Read the USE & CARE Manual.
Printed in China