Important Safety Instructions..............................2-3 Product Registration...............................................4 Normal Sounds.......................................................4 Unit Description......................................................5 Accessories Included.............................................5 Installation Instructions.......................................6-7 Air Conditioner Features.....................................8 Operating Instruction..................
Important Safety Instructions NOTE: NOTE: WARNING WARNING WARNING WARNING SAFETY PRECAUTIONS
Important Safety Instructions SAFETY PRECAUTIONS NOTE:
Product Registration & Normal Sounds Product Registration Record Your Model and Serial Numbers Record in the space provided below the mode and serial numbers. On all models, the serial plate is located on the side of the cabinet. Model No. Serial No. Register Your Product The self-addressed PRODUCT REGISTRATION CARD should be filled in completely, signed and returned to the Frigidaire Company.
Unit Description & Accessories Included Unit Description Air Outlet Grill Control Panel Carrying Handle Signal Receiver Continuous Drain Outlet Continuous Drain Outlet Remote Control Air Exhaust Air Intake Air Intake Power Cord Castor Bottom Drain Outlet Bottom Drain Outlet Power cord (FFPA1222T1、FFPH1222T1 FFPA1422T1、FFPH1422T1) (FFPA0822T1、FFPA1022T1) Accessories Included PARTS: PARTS NAME: QUANTITY: Window Kit Connector A Exhaust hose connector B (FFPA1222T1、FFPH1222T1 FFPA1422T1、FFPH1422
Installation Instructions Installation Instructions EXHAUSTING HOT AIR In the Cool Mode the appliance must be placed close to a window or opening so that the warm exhaust air can be ducted outside. First position unit on a flat floor and make sure there’s a minimum of 12″clearance around the unit, and is within the vicinity of a single circuit outlet power source. Extend the side of hose Fig.1 1. Extend either side of the hose(Fig.1) and screw the hose to connector A (Fig.2). 2.
Installation Instructions Installation Instructions(continued) Installation in a double-hung sash window 1.Cut the foam seals A(adhesive type) to the proper lengths and attach them to the window and stool.(Fig.8) 2.Open the window sash and place the window slider kit on the window stool (Fig.9). Attach the window slider kit to the window stool. Adjust the length of the window slider kit according to the width of window. Screw down the two screws on the window slider kit. See Fig.9.
Air Conditioner Features & Operating Instructions Control Panel Display Temperature/Timer Timer Mode Selection Adjust Temperature or Timer Fan Speed / Filter Reset Power ON/OFF Operating Instruction Cool mode Press the “mode” button until the Cool mode indicator lights. Press the "fan speed" button to choose the fan speed according to the illumination of the fan speed indicator. You can choose the “hi”, “med”, “low”, or “auto” fan speed setting.
Operating Instructions Dry mode Press the “mode” button until the Dry mode indicator lights. The screen displays the room temperature. At the same time, the “low” fan indicator lights. Note: In this mode, fan speed cannot be selected. Fan mode Press the “mode” button until the Fan mode indicator lights. In this mode, you can select fan speed “hi”, “med”, “low” or “auto” . The screen displays room temperature. Note: In this mode, the air exhaust hose does not need to be connected.
Operating Instructions ECO mode Press the “mode” button until the ECO mode indicator lights. Press the "fan speed" button to choose the fan speed according to the illumination of the fan speed indicator. You can choose the “hi”, “med”, “low”, or “auto” fan speed setting. Press the “ ” or “ ” button to choose the temperature you want. In few seconds after you set the temperature, the screen will display the room temperature. Note: The unit will run in energy saver(ECO) mode when used for the first time.
Operating Instructions How to delay shutdown You can delay shutdown when the unit is on. Press the “timer” button, then the Timer indicator and number of hours on the screen will flash. Tap or hold the UP arrow ( ) or the DOWN arrow ( ) to change delay stop timer at 0.5 hour increments up to 10 hours, then at 1 hour increments up to 24 hours. After 5 seconds, the Timer indicator and the display stop flashing, and the display shows the time remaining until the unit shuts down.
Operating Instructions Remote Control Cool Only models Heat and Cool models Remote Control screen Temp/Timer setting button Timer on button Timer off button Sleep button Swing button Mode button On/Off button Fan Speed button Battery Installation and Important Instructions Remove the cover at the back of the remote control. Insert the provided batteries correctly(see the instructions inside the battery compartment). Close up the cover.
Operating Instructions How to Use the Remote Control TURNING THE UNIT ON Plug in the unit, then press the “on/off” button (when turned on, the unit will operate as the last setting before shutdown. To switch the unit off, press “on/off” button again, then remove the plug. Do NOT switch the unit off by removing the plug. Always switch the unit off by pressing the “on/off” button and wait for few minutes before removing the plug.
Operating Instructions Heat mode(For Heat & Cool models only) Press the “mode” button until the left side of LCD screen displays “ ”. Press the “ ” and “ ” button to choose the temperature you want. At the same time, the “low” fan indicator lights. Note: In this mode, fan speed cannot be selected. ECO mode Press the “mode” button until the left side of LCD screen displays “ ”. Press the “fan speed” button to choose the “Hi”, “Med”, “Low” or “Auto” fan speed setting.
Operating Instructions function Press the “ degrees Celsius. ” button to switch between degree Fahrenheit and Timer mode How to delay startup Plug in the unit, so the unit turns to standby. Press the “timer on” button, the screen will display “ ”and “H”. Tap or hold the UP arrow ( ) or the DOWN arrow ( ) to change delay start timer at 0.5 hour increments up to 10 hours, then at 1 hour increments up to 24 hours. After 2 seconds, the setting will be memorized.
Operating Instructions Drainage Instructions Continuous Drainage During the DRY mode, you will need a garden hose (sold separately) to drain the condensate from the unit. Follow the steps below: Unscrew the drain cap of continuous drain outlet(Fig.20). Connect one end of the garden hose (sold separately) to the drain outlet then lead the other end into a drain that is lower than the unit(Fig.21).
Care and Cleaning Cleaning Clean your air conditioner occasionally to keep it looking new. Be sure to unplug the unit before cleaning to prevent shock or fire hazards. CLEANING THE UNIT The cabinet and front may be dusted with an oil-free cloth or washed with a cloth dampened in a solution of warm water and mild liquid dishwashing detergent. Never use harsh cleaners, wax or polish on the cabinet front. Be sure to wring excess water from the cloth before wiping around the controls.
Before You Call
Major Appliance Limited Warranty