Installation guide

ManualsBrandsFrigidaire ManualsRoom air conditionerOfficial Frigidaire room air conditioner

READ BEFORE INSTALLING UNIT

OPP Window Mounting (5,000-6,500 BTU)

Carefully read the installation manual before beginning.

Follow each step as shown.

Observe all local, state, and national electrical codes and by qualified, licensed, authorized personnel only.

Pay attention to danger and safety notices.

To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may

be exposed:

Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and install

the unit. Wear protective gloves whenever lifting or carrying the unit.AVOID the sharp metal fins of front and rear coils. To

prevent injury or strain, use proper lifting and carrying techniques when moving unit.

Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit overan extended

period of time.

Handle air conditioner with care.

Make sure air conditioner does not fall during installation.

• SAVE CARTON and these INSTALLATION

INSTRUCTIONS for future reference. The carton is

the best way to store unit during winter, or when not

in use.

® DO NOT USE ANY SCREWS OTHER THAN

THOSE SPECIFIED HERE.

® FOR SAFETY REASONS, THE TOP RAIL MUST BE

SECURELY FASTENED WITH ALL FOUR (4)

SCREWS.

Some assembly is required. Please read these instructions

Mounting Hardware

112"

screws

lock frame

(ForWoodenwindows)

lock frame

(For Vinyl-Clad windows)

sash lock

weather seals

(6"x3/4"x1/12")

TOOLS NEEDED

® Philips Screwdriver

+ Drill (If pilot holes are needed)

carefully.

Top Rail Hardware Qty.

3/8" Screw 4

Top Rail 1

Before installing, the top rail must be assembled on the unit.

A. Remove the air conditioner from the carton and place on a flat surface.

B. Remove top rail from the rear of the packaging material as shown in Fig. A

C. Align the hole in the top rail with those on the top of the unit as shown in Fig. B

D. Secure the top rail to the unit with the 318" Screws as shown in Fig. C

Top Rail _ i Fig+B

Packaging _ rq

Qty. "_

t Fig. C

2020211A2578

Summary of content (4 pages)

PAGE 1
READ BEFORE INSTALLING UNIT OPP Window Mounting (5,000-6,500 BTU) Carefully read the installation manual before beginning. Follow each step as shown. Observe all local, state, and national electrical codes and by qualified, licensed, authorized personnel only. Pay attention to danger and safety notices.
PAGE 2
LEFT + RIGHT FILLER PANEL ASSEMBLY NOTE: Top Rail and Side Panels at each side are offset to provide the proper pitch to the rear of (5/16"}. This is necessary for proper condensed water utilization and drainage. If you are not using the Side Panels for any reason, this pitch to the rear must be maintained! Place unit on floor, a bench or a table. There is a Left and Right side Filler Panels - be sure to use the proper panel for each side.
PAGE 3
Keep afirmgrip ontheairconditioner, carefully place theunit into thewindow opening sothebottom oftheair conditioner frame isagainst thewindow sill(FIG. 6A&FIG. 6B). Carefully close thewindow behind thetoprail oftheunit. __FIG. 6A INsIDL1E _--7 OUTSIDE INSIDE I Wooden Windows Vinyl-Clad Windows Extend the side panels out against the window frame (FIG. 7Afor wooden windows), windows). FIG. 7A FIG. (FIG.
PAGE 4
Tosecure lower sash inplace, attach right angle sash lock with 1/2" (12.7mm) screw asshown (FIG. 10). NOTE: It is difficult to lock the windows with the sash lock for Vinyl-Clad windows, window itself. so you can use lock by Cut foam window seal and insert it into the space between the upper and lower sashes (FIG. tl). FIG. 10 FIG. 11 / / Check that air conditioner is tilted back about 1/4" to 1/2" (tilted about 2 ° to 4 ° downward to the outside, see FIG. 12A & FIG. 12B).