Installation Instructions

ManualsBrandsFrigidaire ManualsHeating, Ventilation, and Air Conditioning12,000 BTU Window Air Conditioner with Remote

READ BEFORE INSTALLING UNIT

Compact Window Mounting (10,000~12,000 BTU)

Before installing, the top rail must be assembled on the unit.

Top Rail Hardware

Qty.

3/8″ Screw

Top Rail

The top rail on your unit may already be installed. If not,

follow the steps below.

Philips Screwdriver

Drill (If pilot holes are needed)

TOOLS NEEDED

DO NOT USE ANY SCREWS OTHER THAN

THOSE SPECIFIED HERE.

NOTE:

SAVE CARTON and these INSTALLATION

INSTRUCTIONS for future reference. The carton is

the best way to store unit during winter, or when not

in use.

WHERE APPLICABLE, THE TOP RAIL MUST BE

SECURELY FASTENED WITH ALL FOUR (4)

SCREWS FOR SAFETY REASONS.

A. Remove the air conditioner from the carton and place on a flat surface.

B. Remove top rail from the rear of the packaging material as shown in Fig. A

C. Align the hole in the top rail with those on the top of the unit as shown in Fig. B

D. Secure the top rail to the unit with the 3/8″ Screws as shown in Fig. C

Fig. B

16120300A04865

Fig. C

1/2″ screws

sash lock

Mounting Hardware

Qty.

lock frame

(For Vinyl-Clad windows)

lock frame

(For Wooden windows)

weather seals

(6″X3/4″X1/12″)

window sash seal foam 1

Packaging

Top Rail

Fig. A

The unit is for window mounting only.

INSTALLATION WARNINGS AND CAUTION

Pay attention to danger and safety notices.

To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may

be exposed:

Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and install

the unit. Wear protective gloves whenever lifting or carrying the unit. AVOID the sharp metal fins of front and rear coils. To

prevent injury or strain, use proper lifting and carrying techniques when moving unit.

Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit overan extended

period of time.

Handle air conditioner with care.

Make sure air conditioner does not fall during installation.

Carefully read the installation manual before beginning.

Follow each step as shown.

Observe all local, state, and national electrical codes and by qualified, licensed, authorized personnel only.

Summary of content (4 pages)

PAGE 1
Installation Instructions READ BEFORE INSTALLING UNIT Compact Window Mounting (10,000~12,000 BTU) INSTALLATION WARNINGS AND CAUTION The unit is for window mounting only. Carefully read the installation manual before beginning. Follow each step as shown. Observe all local, state, and national electrical codes and by qualified, licensed, authorized personnel only. Pay attention to danger and safety notices.
PAGE 2
How to Install Installation LEFT + RIGHT FILLER PANEL ASSEMBLY NOTE: Top Rail and Side Panels at each side are offset to provide the proper pitch to the rear of (5/16”). This is necessary for proper condensed water utilization and drainage. If you are not using the Side Panels for any reason, this pitch to the rear must be maintained! Place unit on floor, a bench or a table. There is a Left and Right side Filler Panels - be sure to use the proper panel for each side.
PAGE 3
How to Install Installation Keep a firm grip on the air conditioner, carefully place the unit into the window opening so the bottom of the air conditioner frame is against the window sill (FIG. 6A & FIG. 6B). Carefully close the window behind the top rail of the unit. FIG. 6B FIG. 6A INSIDE OUTSIDE INSIDE OUTSIDE Wooden Windows Vinyl-Clad Windows Extend the side panels out against the window frame (FIG. 7A for wooden windows), (FIG. 7B for Vinyl-Clad windows). FIG. 7A FIG.
PAGE 4
Installation To secure lower sash in place, attach right angle sash lock with 1/2″ (12.7mm) screw as shown (FIG. 10). NOTE: It is difficult to lock the windows with the sash lock for Vinyl-Clad windows, so you can use lock by window itself. Cut foam window seal and insert it into the space between the upper and lower sashes (FIG. 11). FIG. 10 FIG. 11 FOAM SEAL Check that air conditioner is tilted back about 1/4″ to 1/2″ (tilted about 2° to 4° downward to the outside, see FIG. 12A & FIG. 12B).