All about the Installation of your Dryer TA B L E O F C O N T E N T S Important Safety Instructions ........................... 2-3 Accessories ...................................................... 19 Installation Requirements .............................. 4-10 Notes .............................................................. 20 Installation Instructions ................................11-16 Français........................................................... 21 Reversing Door ..................
IMPORTANT SAFETY INSTRUCTIONS WARNING For your safety the information in this manual must be followed to minimize the risk of fire or explosion or to prevent property damage, personal injury or loss of life. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. WARNING - RISK OF FIRE Read all of the following instructions before installing and using this appliance: • Destroy the carton and plastic bags after the dryer is unpacked.
IMPORTANT SAFETY INSTRUCTIONS WARNING Please read all instructions before using this dryer.
INSTALLATION REQUIREMENTS NOTE Because of potentially inconsistent voltage capabilities, the use of this dryer with power created by gas powered generators, solar powered generators, wind powered generators or any other generator other than the local utility company is not recommended. Electrical requirements for electric dryer CIRCUIT - Individual 30 amp. branch circuit fused with 30 amp. time delay fuses or circuit breakers. Use separately fused circuits for washer and dryer.
INSTALLATION REQUIREMENTS Electrical requirements for gas dryer CIRCUIT - Individual, properly polarized and grounded 15 amp. branch circuit fused with 15 amp. time delay fuse or circuit breaker. POWER SUPPLY - 2-wire, with ground, 120 volt, single phase, 60 Hz, Alternating Current. POWER SUPPLY CORD - The dryer is equipped with a 120 volt 3-wire power cord. GROUNDING CONNECTION - See “Grounding requirements” in Electrical Installation section.
INSTALLATION REQUIREMENTS Exhaust system requirements Use only 4 inch (102 mm) diameter (minimum) rigid or flexible metal duct and approved vent hood which has a swing-out damper(s) that open when the dryer is in operation. When the dryer stops, the dampers automatically close to prevent drafts and the entrance of insects and rodents. To avoid restricting the outlet, maintain a minimum of 12 inches (30.5 cm) clearance between the vent hood and the ground or any other obstruction.
INSTALLATION REQUIREMENTS Exhaust system requirements, continued WARNING FIRE HAZARD A clothes dryer must be exhausted outdoors. Do not exhaust dryer into a chimney, a wall, a ceiling, an attic, a crawl space or any concealed space of a building. A clothes dryer produces combustible lint. If the dryer is not exhausted outdoors, some fine lint will be expelled into the laundry area. An accumulation of lint in any area of the home can create a health and fire hazard.
INSTALLATION REQUIREMENTS Exhaust system requirements, continued Install male fittings in correct direction: CORRECT Exhaust direction Directional exhausting can be accomplished by installing a quick-turn 90° dryer vent elbow directly to exhaust outlet of dryer. Dryer vent elbows are available through your local parts distributor or hardware store.
INSTALLATION REQUIREMENTS Manufactured or mobile home installation 1 Installation MUST conform to current Manufactured Home Construction & Safety Standard, Title 24 CFR, Part 32-80 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280) or Standard CAN/CSAZ240 MH. 2 Dryer MUST be exhausted outside (outdoors, not beneath the mobile home) using metal ducting that will not support combustion. Metal ducting must be 4 inches (10.16 cm) in diameter with no obstructions.
INSTALLATION REQUIREMENTS Clearance requirements MINIMUM INSTALLATION CLEARANCES - Inches (cm) IMPORTANT DO NOT INSTALL YOUR DRYER: 1 In an area exposed to dripping water or outside weather conditions. 2 In an area where it will come in contact with curtains, drapes, or anything that will obstruct the flow of combustion and ventilation air. 3 On carpet. Floor MUST be solid with a maximum slope of 1 inch (2.54 cm). SIDES REAR TOP FRONT Alcove 0” (0 cm) 0” (0 cm)* 23” (58.
INSTALLATION INSTRUCTIONS Electrical installation The following are specific requirements for proper and safe electrical installation of your dryer. Failure to follow these instructions can create electrical shock and/or a fire hazard. WARNING ELECTRICAL SHOCK HAZARD • This appliance MUST be properly grounded. Electrical shock can result if the dryer is not properly grounded. Follow the instructions in this manual for proper grounding. • Do not use an extension cord with this dryer.
INSTALLATION INSTRUCTIONS Grounding requirements - Electric dryer (Canada) WARNING ELECTRICAL SHOCK HAZARD Improper connection of the equipment grounding conductor can result in a risk of electrical shock. Check with a licensed electrician if you are in doubt as to whether the appliance is properly grounded.
INSTALLATION INSTRUCTIONS Gas connection 1 Remove the shipping cap from gas pipe at the rear of the dryer. 3 Open the shutoff valve in the gas supply line to allow gas to flow through the pipe. Wait a few minutes for gas to move through the gas line. IMPORTANT DO NOT connect the dryer to L.P. gas service without converting the gas valve. An L.P. conversion kit must be installed by a qualified gas technician. 2 Connect a 1/2 inch (1.27 cm) I.D.
INSTALLATION INSTRUCTIONS Electrical connection (non-Canada) - 3 wire cord 3-wire receptacle (NEMA type 10-30R) WARNING 30 AMP NEMA 10-30 Neutral (center wire) ELECTRICAL SHOCK HAZARD Failure to disconnect power source before servicing could result in personal injury or even death. 1 Turn off power supply to outlet. 2 Remove the screw securing the terminal block access cover in the lower corner on the back of the dryer.
INSTALLATION INSTRUCTIONS Electrical connection (non-Canada) - 4 wire cord 4-wire receptacle (NEMA type 14-30R) WARNING Neutral (WHITE wire) Ground (GREEN wire) 30 AMP NEMA 14-30 ELECTRICAL SHOCK HAZARD Failure to disconnect power source before servicing could result in personal injury or even death. 1 Turn off power supply to outlet. 2 Remove the screw securing the terminal block access cover in the lower corner on the back of the dryer.
INSTALLATION INSTRUCTIONS General installation 1 Connect the exhaust duct to the outside exhaust system. Use of a 4” (102 mm) clamp (item A) is recommended to connect the dryer to the exhaust vent system. Use metal foil tape to seal all other joints. 2 Use a carpenter’s level to level your dryer front-toback and side-to-side. 3 Use adjustable pliers to adjust the leveling legs so the dryer is level front-to-rear and side-to-side, and stable corner-to-corner.
REVERSING DOOR Your dryer is designed so the door swing may be reversed at any time without additional parts. Conversion is accomplished by transferring hinges and door strike to the opposite sides of the cabinet. 1 Be sure you have adequate swing area before reversing door. 2 You will need a screw driver with a #2 square bit and a pair of pliers. 3 Protect flat work surface, such as top of dryer or floor near dryer, with a soft cloth or towel.
REVERSING DOOR 5 Install four long screws securing hinge to door assembly in the new location, take note to place each hinge in correct orientation. (Figure below) 9 Install new striker (included in literature bag) into hole square plug was previously installed in. (Figure below) IMPORTANT The plate with the stamped “D” is mounted to the door. The “D” must be visible after the hinge is remounted and the spine of the hinge should be oriented toward the front side of the door for correct operation.
ACCESSORIES LP CONVERSION KIT P/N PCK4200 Gas dryers intended for use in a location supplied with LP must use a conversion kit prior to installation. MOBILE HOME INSTALLATION KIT CAUTION Failure to use accessories manufactured by (or approved by) the manufacturer could result in personal injury, property damage or damage to the dryer. P/N 137067200 Installation in a mobile home requires the use of a MOBILE HOME INSTALLATION KIT.
NOTES 20
Tout à propos de Installation de votre Sécheuse TA B L E D E S M AT I È R E S Mesures de sécurité importantes ...................22-23 Inversion de la porte ....................................37-38 Exigences d’installation .................................24-30 Accessoires ...................................................... 39 Instructions d’installation ..............................31-36 Remarques ......................................................
MESURES DE SÉCURITÉ IMPORTANTES AVERTISSEMENT Pour votre sécurité, l’information contenue dans ces instructions doit être suivie afin de réduire les risques d’incendie ou d’explosion ou pour prévenir les dommages matériels, les blessures ou la mort. Vous ne devez ni entreposer, ni utiliser d’essence ou d’autres vapeurs ou liquides inflammables à proximité de cet appareil ou de tout autre appareil électroménager.
MESURES DE SÉCURITÉ IMPORTANTES AVERTISSEMENT Veuillez lire ces instructions au complet avant d’utiliser le sécheuse. Liste de vérification d’installation Conduit d’évacuation L’air circule librement, il n’y a aucune accumulation de charpie Sachez reconnaître les symboles, les avertissements et les étiquettes de sécurité. Les mesures de sécurité présentées dans ce guide sont identifiées par le mot AVERTISSEMENT ou ATTENTION selon le type de risque présenté ci-dessous.
EXIGENCES D’INSTALLATION REMARQUE Étant donné les variations de tension possibles, l’utilisation de cette sécheuse avec une source d’alimentation produite par une génératrice à essence, solaire ou éolienne ou par toute autre source d’alimentation différente de celle fournie par les services publics n’est pas recommandée. Exigences électriques de la sécheuse électrique: CIRCUIT - Circuit indépendant de 30 ampères avec fusible temporisé ou disjoncteur de 30 A.
EXIGENCES D’INSTALLATION Exigences électriques de la sécheuse gaz CIRCUIT - Circuit indépendant de 15 ampères, polarisé et mis à la terre, avec fusible temporisé ou disjoncteur de 15 A. ALIMENTATION ÉLECTRIQUE - Câble monophasé à deux fils mis à la terre, 120 volts, 60 Hz; courant alternatif. CORDON D’ALIMENTATION - La sécheuse est dotée d’un cordon d’alimentation de 120 volts à trois fils.
EXIGENCES D’INSTALLATION Exigences du système d’évacuation Utilisez seulement des conduites métalliques rigides ou flexibles d’au moins 10,2 cm (4 po) de diamètre, et une bouche d’évacuation qui possède un ou des volets qui s’ouvrent lorsque l’appareil est en fonction. Lorsque la sécheuse s’arrête, les volets se ferment automatiquement pour empêcher les infiltrations d’air, d’insectes et de rongeurs.
EXIGENCES D’INSTALLATION Exigences de système d’évacuation (suite) AVERTISSEMENT La sécheuse doit être branchée à une évacuation extérieure. Inspectez régulièrement l’ouverture de l’évacuation extérieure et retirez toute accumulation de charpie près de l’ouverture et de la région avoisinante. AVERTISSEMENT RISQUE D’INCENDIE • Ne laissez pas de matière combustible (par exemple : des vêtements, des rideaux, du papier) entrer en contact avec le système d’évacuation.
EXIGENCES D’INSTALLATION Exigences de système d’évacuation (suite) Installez les raccords mâles dans le bon sens : CORRECT Direction d’évacuation Il est possible de diriger l’évacuation en posant un coude de 90° à courbe immédiate directement à la sortie d’évacuation de la sécheuse. Les coudes pour évacuation de sécheuse sont disponibles auprès du distributeur de pièces de votre région ou à la quincaillerie.
EXIGENCES D’INSTALLATION Installation dans une maison usinée ou mobile 1 L’installation DOIT être conforme à la norme Manufactured Home Construction and Safety Standard, titre 24 CFR, article 32-80 (anciennement désignée comme la Federal Standard for Mobile Home Construction and Safety, titre 24, HUD, article 280) ou à la norme CAN/CSAZ240 MH. 2 La sécheuse DOIT être évacuée vers l’extérieur (à l’air libre et non sous la maison mobile) avec une gaine métallique ininflammable.
EXIGENCES D’INSTALLATION Exigences de dégagement IMPORTANT DÉGAGEMENTS MINIMAUX - Pouces (Centimètres) N’INSTALLEZ PAS VOTRE SÉCHEUSE : 1 À un endroit exposé aux écoulements d’eau ou aux aléas des conditions météorologiques extérieures. 2 À un endroit où elle entrera en contact avec des rideaux ou tout autre objet qui nuirait à l’écoulement de l’air de combustion ou de ventilation. 3 Sur un tapis. Le plancher DOIT être solide et présenter une pente inférieure à 2,5 cm (1 po).
INSTRUCTIONS D’INSTALLATION Installation électrique Vous trouverez ci-dessous les exigences pour l’installation électrique adéquate et sécuritaire de votre appareil. Le non-respect de ces instructions pourrait entraîner le risque de choc ou d’incendie. AVERTISSEMENT RISQUE DE CHOC ÉLECTRIQUE • Cet appareil DOIT être adéquatement mis à la terre. La mise à la terre inadéquate de la sécheuse pourrait entraîner des risques de choc électrique.
INSTRUCTIONS D’INSTALLATION Exigences de mise à la terre - Sécheuse électrique (Canada) AVERTISSEMENT RISQUE DE CHOC ÉLECTRIQUE Un raccordement inadéquat du conducteur de mise à la terre de l’équipement peut accroître les risques de choc électrique. En cas de doute quant à la mise à la terre de l’appareil, consultez un électricien qualifié. Pour une sécheuse avec cordon, mise à la terre : 1 Cet appareil DOIT être mis à la terre.
INSTRUCTIONS D’INSTALLATION Connexion de gaz 1 Retirez le capuchon d’expédition de la conduite de gaz à l’arrière de l’appareil. IMPORTANT NE RACCORDEZ PAS la sécheuse à une alimentation en propane liquide sans avoir préalablement converti la soupape de gaz. Le nécessaire de conversion au propane liquide doit être installé par un technicien qualifié.
INSTRUCTIONS D’INSTALLATION Connexion électrique (sauf au Canada) - cordon à 3 fils Prise à 3 alvéoles (NEMA type 10-30R) 30 AMP NEMA 10-30 AVERTISSEMENT RISQUE DE CHOC ÉLECTRIQUE Le fait de ne pas débrancher l’appareil de sa source d’alimentation en électricité avant son entretien peut causer des blessures, voire la mort. 1 Coupez l’alimentation à la prise. 2 Retirez la vis qui fixe le couvercle d’accès du bornier dans le coin inférieur du dos de la sécheuse.
INSTRUCTIONS D’INSTALLATION Connexion électrique (sauf au Canada) - cordon à 4 fils Prise à 4 alvéoles (NEMA type 14-30R) AVERTISSEMENT Fils neutres Mises à la terre (Fils BLANCS) (Fils VERTS) 30 AMP NEMA 14-30 RISQUE DE CHOC ÉLECTRIQUE Le fait de ne pas débrancher l’appareil de sa source d’alimentation en électricité avant son entretien peut causer des blessures, voire la mort. 1 Coupez l’alimentation à la prise.
INSTRUCTIONS D’INSTALLATION Installation (générale) 1 Branchez la conduite d’évacuation au système d’évacuation extérieur L’utilisation d’un collier (pièce A) de 102 mm (4 po) est recommandée pour raccorder la sécheuse au système d’évacuation. Utilisez du ruban métallique pour sceller les autres joints. 2 Utilisez un niveau à bulle pour mettre l’appareil à niveau de l’avant vers l’arrière et latéralement.
INVERSION DE LA PORTE La sécheuse est conçue de façon que l’ouverture de la porte puisse être inversée en tout temps sans pièces additionnelles. L’inversion de la porte requiert le transfert des charnières au côté opposé du châssis. 1 Assurez-vous qu’il y a suffisamment d’espace avant d’inverser la porte. 2 Vous aurez besoin d’un tournevis à pointe carrée n° 2. 3 Protégez la surface de travail, comme le dessus de la sécheuse ou le plancher près de la sécheuse, avec un chiffon doux ou une serviette.
INVERSION DE LA PORTE 5 À l’aide de quatre grandes vis, fixez les charnières à la porte dans les trous du côté opposé. Assurez-vous d’orienter les charnières dans la bonne direction (voir l’illustration ci-dessous). 9 Installez une nouvelle gâche (incluse dans le sac contenant le manuel d’utilisation) dans le trou qui contenait le bouchon carré que vous avez retiré (voir l’illustration ci-dessous). IMPORTANT La plaque marquée d’un « D » doit être fixée du côté de la porte.
ACCESSOIRES NÉCESSAIRE DE CONVERSION AU GPL ATTENTION PIÈCE N° PCK4200 Les sécheuses à gaz qui seront utilisées dans un endroit alimenté par du propane liquide doivent recourir à un nécessaire de conversion avant l’installation. TROUSSE D’INSTALLATION DE MAISON MOBILE Tout défaut d’utiliser les accessoires fabriqués ou certifiés par le fabricant pourrait entraîner des blessures, des dommages aux biens ou à la sécheuse.
REMARQUES 40
Todo acerca del Instalación de su Secadora ÍNDICE Instrucciones importantes de seguridad .........42-43 Inversión de la puerta...................................57-58 Requisitos de instalación ...............................44-50 Accesorios ....................................................... 59 Instrucciones de instalación ..........................
INSTRUCCIONES IMPORTANTES DE SEGURIDAD ADVERTENCIA Para su seguridad, debe seguir la información de esta guía para minimizar el riesgo de incendio o explosión o para evitar daños a la propiedad, lesiones personales o incluso la muerte. No almacene ni utilice gasolina ni otros líquidos o vapores inflamables cerca de este o de cualquier otro electrodoméstico.
INSTRUCCIONES IMPORTANTES DE SEGURIDAD ADVERTENCIA Lea todas las instrucciones antes de usar este secadora. Lista de verificación de instalación Ventilación de escape De flujo libre y sin acumulación de pelusa Identificación de los símbolos, palabras y avisos de seguridad Las indicaciones de seguridad incluidas en este manual aparecen precedidas de un aviso titulado “ADVERTENCIA” o “PRECAUCIÓN”, de acuerdo con el nivel de riesgo.
REQUISITOS DE INSTALACIÓN NOTA Debido a posibles variaciones en el voltaje, no se recomienda utilizar esta secadora con electricidad generada a partir de generadores a gas, solares, eólicos ni de ninguna otra clase que no sean los empleados por su empresa de electricidad local. Requisitos eléctricos de la secadora eléctrica: CIRCUITO: circuito independiente individual de 30 amp. con fusibles de acción retardada o disyuntores. Use circuitos con fusibles separados para la lavadora y la secadora.
REQUISITOS DE INSTALACIÓN Requisitos eléctricos de la secadora a gas: CIRCUITO - Circuito individual de bifurcación de 15 amp., correctamente polarizado y con conexión a tierra con fusible de retardo de 15 amp. o con interruptor automático. SUMINISTRO ELÉCTRICO: corriente alterna de 2 cables, con conexión a tierra, 120 voltios, monofásica, 60 Hz. CABLE DE ALIMENTACIÓN ELÉCTRICA: la secadora está equipada con un cable de alimentación trifilar de 120 voltios.
REQUISITOS DE INSTALACIÓN Requisitos del sistema de escape Utilice solo un conducto de metal flexible o rígido de 10,2 cm (4 pulgadas) de diámetro (mínimo) y una capucha de ventilación aprobada que tenga uno o más reguladores de tiro que se abran cuando la secadora esté en funcionamiento. Cuando la secadora se detiene, el regulador de tiro se cierra automáticamente para evitar la corriente de aire y el ingreso de insectos y roedores.
REQUISITOS DE INSTALACIÓN Requisitos del sistema de escape (continuación) ADVERTENCIA La secadora debe estar conectada a un sistema de escape que termine en el exterior de la vivienda. Inspeccione la abertura de escape al exterior con frecuencia y elimine cualquier acumulación de pelusa en la abertura y en el área que la rodea. ADVERTENCIA PELIGRO DE INCENDIO • No permita que materiales combustibles (por ejemplo: ropa, tapicería/cortinas, papel) entren en contacto con el sistema de escape.
REQUISITOS DE INSTALACIÓN Requisitos del sistema de escape (continuación) Instale los accesorios macho en la dirección correcta: CORRECTO Dirección del escape El escape direccional se puede lograr mediante la instalación de un codo de ventilación de giro rápido de 90° directamente en la salida de la secadora. Los codos de ventilación de la secadora se encuentran disponibles a través de su distribuidor de repuestos o ferretería local.
REQUISITOS DE INSTALACIÓN Instalación en una casa rodante 1 La instalación DEBE cumplir con la actual Norma de Seguridad y Construcción de Casas Rodantes, título 24 CFR, Parte 32-80 (que anteriormente se conocía como la Norma Federal de Seguridad y Construcción de Casas Rodantes [Federal Standard for Mobile Home Construction and Safety], título 24, HUD parte 280) o la Norma CAN/CSAZ240 MH.
REQUISITOS DE INSTALACIÓN Requisitos de despeje IMPORTANTE ESPACIOS MÍNIMOS PARA LA INSTALACIÓN: cm NO INSTALE LA SECADORA: 1 En una zona expuesta a la humedad o a las condiciones climáticas externas. 2 En un área en la que esté en contacto con cortinas, telas colgantes o cualquier otra cosa que pueda obstruir el flujo de aire de ventilación y combustión. 3 Sobre una alfombra. El piso DEBE ser firme con una pendiente máxima de 2,5 cm (1 pulgada).
INSTRUCCIONES DE INSTALACIÓN Instalación eléctrica Los siguientes son requisitos necesarios para la instalación eléctrica segura y correcta de su secadora. El no seguir estas instrucciones puede producir una descarga eléctrica y/o incendio. ADVERTENCIA PELIGRO DE DESCARGA ELÉCTRICA • Este electrodoméstico DEBE estar debidamente conectado a tierra. Si la secadora no está conectada a tierra correctamente, se pueden producir descargas eléctricas.
INSTRUCCIONES DE INSTALACIÓN Requisitos de conexión a tierra: secadora eléctrica (Canadá) ADVERTENCIA PELIGRO DE DESCARGA ELÉCTRICA Una conexión incorrecta del conductor de conexión a tierra del equipo puede provocar un peligro de descarga eléctrica. Si no está seguro de haber realizado correctamente la conexión a tierra del artefacto, consulte a un electricista autorizado. Para una secadora conectada a tierra: 1 La secadora DEBE tener conexión a tierra.
INSTRUCCIONES DE INSTALACIÓN Conexión de gas 1 Quite el tapón del tubo de gas en la parte trasera de la secadora. IMPORTANTE NO conecte la secadora al servicio de gas LP sin convertir la válvula de gas. El kit de conversión a gas LP debe ser instalado por un técnico calificado. 2 Conecte un tubo aprobado o uno semi-rígido de 1,27 cm (1/2 pulgada) de diámetro interior desde la línea de suministro de gas al tubo de 0,96 cm (3/8 pulgada) ubicado en la parte trasera de la secadora.
INSTRUCCIONES DE INSTALACIÓN Conexión eléctrica (fuera de Canadá): trifilar Receptáculo trifilar (tipo NEMA 10-30R) ADVERTENCIA 30 AMP NEMA 10-30 PELIGRO DE DESCARGA ELÉCTRICA El no desconectar el suministro eléctrico antes de realizar cualquier reparación puede ocasionar lesiones personales o incluso la muerte. 1 Desconecte el suministro eléctrico del tomacorriente.
INSTRUCCIONES DE INSTALACIÓN Conexión eléctrica (fuera de Canadá): tetrafilar Receptáculo tetrafilar (tipo NEMA 14-30R) ADVERTENCIA Neutro (cable BLANCO) Tierra (cable VERDE) 30 AMP NEMA 14-30 PELIGRO DE DESCARGA ELÉCTRICA El no desconectar el suministro eléctrico antes de realizar cualquier reparación puede ocasionar lesiones personales o incluso la muerte. 1 Desconecte el suministro eléctrico del tomacorriente.
INSTRUCCIONES DE INSTALACIÓN Instalación general 1 Conecte el tubo de escape al sistema de escape exterior. Se recomienda usar una abrazadera (pieza A) de 4” (10,2 cm) para conectar las secadora al sistema de ventilación de escape. Utilice cinta de papel de aluminio para sellar las demás uniones. 2 Utilice un nivel de carpintero para nivelar todos los costados de la secadora.
INVERSIÓN DE LA PUERTA Su secadora ha sido diseñada para que la puerta pueda ser cambiada de lado en cualquier momento sin necesidad de piezas adicionales. La conversión se hace transfiriendo las bisagras al lado opuesto del gabinete. 1 Asegúrese de que haya suficiente espacio de giro antes de invertir la puerta. 2 Necesitará un destornillador con punta cuadrada n.º 2.
INVERSIÓN DE LA PUERTA 5 Instale los cuatro tornillos largos que sujetan la bisagra al conjunto de la puerta en la nueva ubicación, teniendo en cuenta la orientación correcta al colocar cada bisagra. (Como se muestra en la figura más abajo) 9 Instale el nuevo pestillo (incluido en la bolsa con los manuales) en el agujero en el que se estaba instalado previamente el tapón cuadrado. (Como se muestra en la figura más abajo) IMPORTANTE La placa con la “D” estampada se instala en la puerta.
ACCESORIOS KIT DE CONVERSIÓN A GAS LP Pieza No.. PCK4200 Las secadoras a gas diseñadas para el uso en lugares con suministro de LP requieren utilizar un kit de conversión antes de la instalación. PRECAUCIÓN El no utilizar accesorios fabricados (o aprobados) por el fabricante puede ocasionar lesiones personales, daños a la propiedad o daños a la secadora. KIT DE INSTALACIÓN EN UNA CASA RODANTE Pieza No..