Installation Instructions READ BEFORE INSTALLING UNIT Compact Window Mounting (10,000~12,000 BTU) INSTALLATION WARNINGS AND CAUTION The unit is for window mounting only. Carefully read the installation manual before beginning. Pay attention to danger and safety notices. be exposed: Carefully inspect location where air conditioner will be inst period of time. Handle air conditioner with care. NOTE: Qty. Mounting Hardware 7 2 the best way to store unit during winter, or when not in use.
How to Install Installation LEFT + RIGHT FILLER PANEL ASSEMBLY NOTE: Top Rail and Side Panels at each side are offset to provide the proper pitch to the rear of (5/16”). This is necessary for proper condensed water utilization and drainage. If you are not using the Side Panels for any reason, this pitch to the rear must be maintained! Place unit on floor, a bench or a table. There is a Left and Right side Filler Panels - be sure to use the proper panel for each side.
How to Install Installation Keep a firm grip on the air conditioner, carefully place the unit into the window opening so the bottom of the air conditioner frame is against the window sill (FIG. 6A & FIG. 6B). Carefully close the window behind the top rail of the unit. FIG. 6B FIG. 6A INSIDE OUTSIDE INSIDE OUTSIDE Wooden Windows Vinyl-Clad Windows Extend the side panels out against the window frame (FIG. 7A for wooden windows), (FIG. 7B for Vinyl-Clad windows). FIG. 7A FIG.
Installation Measure the width of the inner side curtain with the provided ruler, as shown (FIG. 10). Mark a line on the patterned side of the provided insulation panel according to the measured width, then cut out the insulation panel along the line, as shown (FIG.11). Place the patterned side of the insulation panel to face inside your room, then slide the insulation panel into the frame until the panel goes into the side curtain frame completely.
Installation 10 FIG. 15A & FIG. 15B). normal use, correct the slope otherwise. FIG. 15A FIG. 15B H H INSIDE OUTSIDE H about Bottom Rail INSIDE OUTSIDE Bottom Rail H1 Wooden Window Vinyl-Clad Window FIG. 16 11 In order to minimize air leaks between the room air conditioner and the window opening, suitable weather stripping(trim the provided weather stripping into suitable size) should be applied in case of any gaps found at the location as indicated by the arrows in Fig. 16.
Instrucciones de montaje LEA ESTO ANTES DE MONTAR LA UNIDAD Montado Compacto Ventana (10,000~12,000 BTU) IADVERTENCIAS PARA INSTALACION Y PRECAUCIÓN La unidad es para la montaje de ventana solamente. Lea cuidadosamente el manual de instalación antes de comenzar. Siga cada paso como se indica. Observe todos los códigos eléctricos locales, estatales y nacionales y haga la instalación solo con personal calificado, matriculado y autorizado. Preste atención a las notificaciones sobre peligro y seguridad.
How to Install Instalación MONTAJE DEL PANEL DE RELLENO IZQUIERDO Y DERECHO NOTA: El raíl superior y los paneles laterales a cada lado se compensan para proporcionar el espacio necesario a la parte trasera de (5/16”). Esto es necesario para el adecuado tratamiento y drenaje del agua condensada. ¡Si no usa los paneles laterales por alguna razón, debe mantener este espacio hasta la parte trasera! Ponga la unidad sobre el suelo, un banco o una mesa de trabajo.
How to Install Instalación Sujete firmemente el aparato de aire acondicionado, y colóquelo con cuidado sobre la apertura de la ventana de tal modo que la parte inferior de cuadro quede sobre el antepecho (FIG. 6A & FIG. 6B). Baje con cuidado la ventana por detrás del raíl superior de la unidad. FIG. 6B FIG. 6A INTERIOR EXTERIOR INTERIOR EXTERIOR Ventanas de madera Ventanas de PVC Extienda los paneles laterales hasta el marco de la ventana (FIG. 7A para ventanas de madera), (FIG.
Instalación Mida el ancho de la cortina interior con la regla proporcionada, como se muestra (FIG. 10). Marque una línea por el lado modelado del panel de aislamiento proporcionado según la anchura medida y, a continuación, corte el panel de aislamiento por la línea, como se muestra (FIG. 11).
Instalación Compruebe que el aire acondicionado esté inclinado hacia atrás DOUHGHGRU GH Ǝ D Ǝ LQFOLQDGR GH D KDFLD DEDMR \ DIXHUD YHD ),* 5$ ),* 5% 'HVSXpV GH KDFHU OD LQVWDODFLyQ HO FRQGHQVDGR Qo debe drenar por el orificio de drenaje durante el uso normal, en casR OR FRQWUDULR FRUULMD OD LQFOLQDFLyQ ),* $ ),* % H H INTERIOR EXTERIOR INTERIOR EXTERIOR + + + HQWUH Ǝ \ Ǝ H entre Ǝ \ Ǝ Raíl inferior H1 + Raíl inferior Ventana de PVC Ventana de mad
Instructions d’installation LIRE AVANT D’INSTALLER L’UNITÉ Installation pour fenêtre compacte (10,000~12,000 BTU) AVERTISSEMENTS D'INSTALLATION ET ATTENTION L'unité est destinée à la fenêtre de montage. Lisez attentivement le manuel d'installation avant de commencer. Suivez chaque étape comme indiqué. Respectez tous les codes électriques locaux, fédéraux et nationaux à l'aide de personnel qualifié, licencié et autorisé uniquement. Prêtez attention aux avis de danger et de sécurité.
How to Install Installation ASSEMBLAGE DE BOUCLIERS GAUCHE ET DROIT REMARQUE: le rail supérieur et les panneaux latéraux sur chaque côté sont décalés pour fournir le degré approprié à l’arrière de (5/16”). Ceci est nécessaire pour l’utilisation et le drainage d’eau condensée appropriées. Si vous n’utilisez pas les panneaux latéraux pour une raison quelconque, ce degré à l’arrière doit être maintenu! Placez l’unité sur le sol, un banc ou une table.
How to Install Installation Gardez une prise ferme sur le climatiseur, placez avec précaution l’unité dans l’ouverture de fenêtre afin que le bas du cadre de climatiseur soit contre le rebord de fenêtre (FIG. 6A et FIG. 6B). Fermez avec précaution la fenêtre derrière le rail supérieur de l’unité. FIG. 6B FIG. 6A EXTÉRIEUR INTÉRIEUR INTÉRIEUR EXTÉRIEUR Fenêtres en bois Fenêtres à revêtement en vinyle Étendez les panneaux latéraux contre le cadre de fenêtre (FIG. 7A pour les fenêtres en bois), (FIG.
Installation Mesurez la largeur intérieure du rideau latéral avec la règle fournie, comme à la FIG. 10. Faites une ligne du côté motif du panneau isolant fourni selon la largeur mesurée, puis découpez le panneau isolant le long de la ligne, comme à la FIG. 11. Placez le côté motif du panneau isolation pour faire face à l'intérieur de votre chambre, puis faites glisser le panneau isolation dans le cadre jusqu'à ce que le panneau va dans le cadre de rideau de côté complètement.
Installation Vérifiez que le climatiseur est incliné vers l'arrière d'environ 1/4 à 1/2 pouces (incliné de 2 à 4 degrés vers le bas à l'extérieur, voir FIG. 15A & FIG. 15B). Après une installation adéquate, le condensat ne doit pas s'écouler de l'orifice d'évacuation de trop-plein durant l'utilisation normale, sinon corrigez à nouveau la pente. FIG. 15A FIG.