Specification
INSTALLATION SPECIFICATIONS
•
Product Shipping Weight (approx.) – 143 Lbs.
•
Designed for HOME USE only, not recommended for commercial application.
•
An electrical supply with grounded three-prong receptacle is required.
The power supply circuit must be installed in accordance with current edition
of National Electrical Code (ANSI/NFPA 70) and local codes & ordinances.
(Do not use same circuit as washer.)
•
Voltage Rating – 120V / 60
•
Amps @ 120 Volts = 9.0 Amps
•
Connected Load (kW Rating) @ 120 Volts = 4.0 kW
•
Equipped with 120V 3-wire power supply cord, approx. 67" long.
•
Always consult local and national electric & gas codes.
•
Dryer installation requires 1" minimum installation clearance on each side
of unit and 6" minimum at back. To achieve 6" minimum rear clearance, dryer
MUST use 90° quick-turn vent elbow. Closet installation requires 2" minimum
clearance between front of unit and vented door. Door MUST be vented
with 120 sq. in. minimum louvered opening, equally divided, located 3" from
top and bottom of door. A louvered door with equivalent air openings for full-
length of door is acceptable. Air openings MUST remain unobstructed with
door installed. (For additional installation details, refer to Product Installation
Guide on web.)
•
Do NOT install in area exposed to dripping water or outdoor weather
conditions; where gasoline or other flammables are kept or stored; or where
dryer comes in contact with curtains, drapes or anything that will obstruct
flow of combustion and ventilation air.
•
For garage installation, dryer MUST be located minimum 18" above floor.
•
Floor MUST be solid with 1" maximum slope. Do NOT install on carpeted surface.
•
Dryer MUST exhaust to outside of building, NOT into any concealed space.
•
Exhaust installation requires minimum 4"-diameter rigid or semi-rigid metal
duct with approved, unobstructed vent hood having swing-out damper(s).
If installing rigid metal duct (preferred), do not exceed MAXIMUM venting run
length of 64 ft., allow deductions for elbows and vents. If installing semi-rigid
metal duct, do not exceed MAXIMUM venting run length of 8 ft., always allow
deductions for elbows and vents (Refer to Product Installation Guide on web
for additional information). Do NOT use flexible plastic or metal foil duct
and use shortest run possible.
•
Gas supply line should be 1/2" black iron, stainless steel, or plastic-coated brass
pipe and MUST have individual shutoff valve, located within 6 feet of dryer.
Gas supply line must be installed in accordance with current edition of National
Fuel Gas Code (ANSI Z223.1) and local codes & ordinances.
•
Leveling legs supplied to level dryer properly and reduce excessive noise
and vibration.
Specifications subject to change. Accessories information available on the web at frigidaire.com / frigidaire.ca
Note: For planning purposes only. Always consult local and national electric, gas and plumbing codes.
Refer to Product Installation Guide for detailed installation instructions on the web at frigidaire.com / frigidaire.ca.
USA
•
10200 David Taylor Drive
•
Charlotte, NC 28262
•
1-800-FRIGIDAIRE
•
frigidaire.com
CANADA
•
5855 Terry Fox Way
•
Mississauga, ON L5V 3E4
•
1-800-265-8352
•
frigidaire.ca
FFRG4120S 06/18
© 2018 Electrolux Home Products, Inc.
Top Load Laundry - Gas Dryer
Frigidaire Baseline (S Models)
Front
38
1
/2"
44
1
/4"
12
1
/8"14
7
/8"
Rear vent
3
3
/
4
"
Recess or Closet Installation
Dryer installation requires 1" minimum installation
clearance on each side of unit and 6" minimum at
back. To achieve 6" minimum rear clearance, dryer
MUST use 90° quick-turn vent elbow. Closet
installation requires 2"
minimum clearance between
front of unit and vented door. Door MUST be vented
with 120 sq.
in. minimum louvered opening, equally
divided, located 3" from top and bottom of door.
A louvered door with equivalent air openings for
full-length of door is acceptable. Air openings
MUST remain unobstructed with door installed.
For additional installation details, refer to
Product Installation Guide on web.
30
13
/16"
48
5
/8"
Side
Vented door
6"
min. 2"
min.
Side
60"
sq.
in.
min.
3"
60"
sq.
in.
min.
3"
1"
min. 1"
min.
24"
min.
Front
Reversible
Door Swing
27"
120V Power cord
(rear) - 67" long
5
1
/8"
2
5
/8"
Gas supply pipe (rear)
FFRG4120SW
GAS DRYER
6.7 CU. FT. D.O.E.