Wiring Diagram

ManualsBrandsFrigidaire ManualsTop Load WashersFrigidaire White Top Load Washer

7 8

1 2

1110 129 13 14 15

3 4 5 6

A11200301 (1710)

USA 1-877-435-3287

This information is intended for Qualiﬁed Technicians Only.

TABLE OF CONTENTS

Safety items throughout this manual are labeled with a WARNING or

CAUTION based on the risk type as described below:

Washer Tech Data Sheet

www.electroluxappliances.com

Canada 1-800-265-8352

Push Button Cycle Select Washer User Interface

This symbol alerts you to situations that may

cause bodily injury or property damage.

This symbol alerts you to situations that may

cause serious body harm, death or property

damage.

CAUTION

WARNING

CAUTION

Unless otherwise directed, disconnect electrical current before

servicing.

Washer Tech Data Sheet

......................................................................

Diagnostic Mode Tests ..........................................................................2

..............................................................................

Washer Error Codes

...........................................................................

Troubleshooting Tests

Wiring Diagrams ....................................................................................

WARNING

The information within this manual is intended for Qualiﬁed

Service Technicians Only.

• DO NOT reach into the appliance while the tub or drum is

spinning.

• Disconnect power before servicing machine.

• Certain internal parts are intentionally not grounded and may

present a risk of electric shock only during servicing.

1. Power Button

2. Cycle Selector

3. Favorite

4. Digital Display

5. Soak Button

6. Extra Rinse Button

7. Start/Pause Button

8. Cycle Status Indicator Lights

9. Max Fill

10. Delay Button

11. Soil Level Button

12. Control Lock

13. Temp Button

14. Fabric Softener

15. Chime

To enter the test mode, Press Soak button, Extra Rinse button,

and Power button simultaneously.

During tests, when the unit is powered ON, you can turn it OFF

anytime by pressing the Power button.

Note:

Before entering the test mode, empty the washer and make sure

that there is no water left int the tub. Run a spin cycle or open the

service panel from the front side of the unit to drain all the water.

Then, make sure that all the parts are in their original position.

Entering Diagnostic Mode:

Summary of content (6 pages)

PAGE 1
Washer Tech Data Sheet 1 This information is intended for Qualiﬁed Technicians Only. TABLE OF CONTENTS Washer Tech Data Sheet ......................................................................1 Diagnostic Mode Tests ..........................................................................2 Washer Error Codes ..............................................................................3 Troubleshooting Tests ...........................................................................
PAGE 2
Diagnostic Mode Tests Test Modes Test 1: Anytime you enter the test mode, all lights and digital display are ON and then ﬂash with 6 beeps. If any light is not ON, replace the control/display board. If the display does not show 88, replace the board. If no beep sound, replace the board.
PAGE 3
Washer Error Codes Washer Error Codes, continued Fault Code Possible Issue Corrective Action Check if the lid is open. Turn both the faucets on fully. E1 Water not entering or slow water ﬁll Check if the water pressure is in the required range. Straighten the water inlet hoses. Hose ﬁlter screens may be clogged. Disconnect hoses and clean the screens. E2 Water not draining Check the fuse or reset the circuit breaker. Straighten the drain hoses. Eliminate twisted hoses.
PAGE 4
Troubleshooting Tests 4 Washer Troubleshooting Tests, continued Test Number Problem Solution Test 1 The unit doesn’t start. - Check the fuse or reset the circuit breaker. - Make sure your washer is plugged in. - Make sure the lid is closed. - Make sure the water source faucets are open. - Make sure to press the Start/Pause button to start your washer. - Make sure Control Lock is not activated. - Check if a Delay Start is set.
PAGE 5
Troubleshooting Tests Washer Troubleshooting Tests, continued Test Number Problem Solution Test 7 Fills with wrong temperature water. - Turn both faucets fully. - Make sure the temperature selection is correct. - Make sure the hoses are connected to the correct faucets. Flush water lines. - Disconnect the hoses and clean the screens. The hose ﬁlter screens may be clogged. Test 8 Load is too wet at the end of the cycle. - Use high efﬁciency detergent to reduce over-sudsing.
PAGE 6
Wiring Diagrams Wiring Diagram 1200-1800Ω Cold Valve - TO UI BOARD 700-1300Ω Reatractor Hot Valve Drain Pump 3-5Ω 700-1300Ω 10-30Ω Softener Valve Detergent Valve 50-70μF 1 2 3 4 CN3 CN8 CN5 1 2 3 4 5 6 1 1 2 2 CN6 1 PCB 2 CN1 1 CN7 CN4 1 1 2 3 4 5 6 2 2 CN12 7 Power Plug DOOR LOCK WATER LEVEL SENSOR 26KHZ~27.5KHZ Water level sensor frequency combine water level Page 30 Frequency(KHz) Level(inch) 21.05 19.8±0.