Wiring Diagram
SERVICE DATA SHEET
P/N: 807027901 Rev.C
Artwork: 807027901 Rev.003
This information is intended for use by persons having electrical and
mechanical training and a level of knowledge of these subjects generally
considered acceptable in the appliance repair trade. Electrolux Home
Products North America cannot be responsible, nor assume any liability,
for injury or damage of any kind arising from the use of this Service
Data Sheet.
BK............Black
BU............Blue
PK............Pink
R..............Red
Viol..........Violet
W.............White
Y..............Yellow
R-Y.........Red/Yellow
R-BK......Red/Black
COLOR CODE OPERATION
WARNING
DISPLAY CODES (LED)
WIRING DIAGRAM
CYCLE SELECTION OPTIONS
To start ----------------- Close door fully to latch. Press START/CANCEL pad.
To delay start --------- Close door fully to latch. Press DELAY START pad to select desired
delay time.
To select a new cycle
or option ------------- Press desired cycle and/or option pad. The indicator lights will change. Press
START/CANCEL within 15 seconds to begin cycle.
To cancel
a cycle ---------------- Press START/CANCEL. Dishwasher will drain for 90 seconds, then
shut off.
To cancel
a cycle ---------------- Press and hold the AIR DRY pad for 3 seconds. To unlock, press and hold the
AIR DRY pad for 3 seconds.
Disconnect electrical power at the
fuse box or circuit breaker box
before servicing under this product.
Electrical power may be present on
some parts under this product, even if
not in use.
Failure to follow this warning could
result in serious injury or death.
SENSING ----------- Turbidity sensor is checking the condition of the wash/rinse
water. No sensing for LIGHT WASH (UPPER RACK), LIGHT
WASH (LOWER RACK) and CHINA/CRYSTAL.
WASHING---------- Wash portion of cycle.
SANITIZED--------- The SANITIZED criteria has been met. Indicator light
and switch of when door is opened.
DRYING------------ Drying portion of cycle.
CLEAN-------------- Shows completion of cycle. Indicator light will switch
off when door is opened.
Option LED’s
Flashing------------ HI-TEMP WASH and NO HEAT DRY/POWER DRY OFF LED’s
fl ashing indicates power failure has occurred. Press START/
CANCEL pad and reselect desired options and cycle.
Interval Number
Description
1
2
6
4
3
5
7
8
Fill/Det. Dispenser
Fill
Wash/Heat/Det. Disp.
Wash/Heat/Det. Disp.
Wash/Heat
Pause/Heat
Drain
Dry Heater On/Drain
End State
Interval Duration
(sec)
60
27
60
0.4
75
60
90
90
Water Valve
Circulation Motor
Drain Motor
Heater
Dispenser
Clean LED
Washing LED
Drying LED
Sanitize LED
0
WATER/SERVICE TEST
The water/service test,
(WST) is a special function
initiated from the power
failure mode or idle mode.
While in power failure mode
- simultaneously press the AIR
DRY and START/CANCEL pads
for 1
1
/
2
seconds. While in Idle
Mode, simultaneously press
HI-TEMP WASH and START/
CANCEL pads for 6 seconds.
The dishwasher will then step
through the test cycle per the
chart. Pushing the START/
CANCEL pad will advance the
dishwasher to the next step.
Fill Number
1
1
1
1
1
1
1
1
9 1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1 1
1
1
1
1
1
0
0
0
0
0
0
0
0 0
0
0
0
0
0
0
0
0
0
0
0
X
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0 0
0
0
0
0 0 0
E
lectr
onic
S
eries