Installation guide

ManualsBrandsFrigidaire ManualsRangeOfficial Frigidaire electric range

UnitedStates INSTALLATION AND SERVICEMUST BEPERFORMED BY A QUALIFIED INSTALLER. Canada

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

FOR YOUR SAFETY: Do not store or use gasoline or other

flammable vapors and liquids in the vicinity of this or any other appliance.

1. Clearances and Dimensions

a. Provide adequate clearances between the range and adjacent combustible surfaces.

b. Location--Check location where the range will be installed. Check for proper electrical supply and the stability of floor.

c. Dimensions that are shown must be used. Given dimensions provide minimum clearance. Contact surface must

be solid and level.

FRONT TYPICAL CABINET INSTALLATION

v w°l 30 F

Minimum 1'

Minimumto 1"4P _- I Minimurnto

wall on either _ _ 18" cabinets on

side of range ! eitherside

above 36" height. _ _, of range,

_-------301/8"--------_

1_-13"÷

Maximumdepth f_

for cabinets f/I

ab_ ra_g_t°_ _ I

25"

0" clearance below cooking top and at rear of range.

FRONT

VIEW

49"

Maximum

36 t 1/8"

30" minimum clearance between the top of the cooking surface

and the bottom of an unprotected wood or metal cabinet; or 24 "

minimum when bottom of wood or metal cabinet is protected by not

less than W' flame retardant millboard covered with not less than

no. 28 MSG sheet steel, 0.015" stainless steel, 0.024" aluminum

or 0.020" copper. The minimum clearance is 0" for the rear of the

range. Follow all dimension requirements provided above to prevent

property damage, potential fire hazard, and incorrect countertop

and cabinet cuts.

Avoid locating cabinet storage space above the surface units

to eliminate the possibility of cabinets catching on fire, or

personal burns from reaching for the cabinets over the heated

units. If cabinet storage is to be provided, risk can be reduced by

installing a range hood that projects horizontally a minimum of

5" beyond the bottom of the cabinets.

Important Notes to the Installer

1. Read all instructions contained in these installation instructions

before installing the appliance.

2. Remove all packing material before connecting the electrical

supply to the appliance.

3. Observe all governing codes and ordinances.

4. Be sure to leave these instructions with the consumer.

BACK

VIEW

- _ _'---_ _ _ i Alldimensions for _*'

-...... _electrical outlet _

::.........locationarema,imum,

_ Cubed area shows

Terminal i where the electrical i

Block _ outlet must be

Location _ installed for the i

I "_ range to be flush to i

"_ Q'!_ _ \thewall. /

>o,_-_'J =_ i _1 _............................................................................................

Important Note to the Consumer

Keep these instructions with your Use and Care Guide for future reference.

Printed in United States

318201724 (0904) Rev. A

Summary of content (12 pages)

PAGE 1
United States INSTALLATION AND SERVICEMUST BE PERFORMED BY A QUALIFIED INSTALLER. IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE. READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. flammable 1. Clearances Canada FOR YOUR SAFETY: Do not store or use gasoline or other vapors and liquids in the vicinity of this or any other appliance. and Dimensions a. Provide adequate clearances between the range and adjacent combustible surfaces. b. Location--Check location where the range will be installed.
PAGE 2
= Install Anti-Tip Bracket The user is responsible for connecting the power supply cord to the connection block located behind the back panel access cover. (See instructions on page 4.) = This appliance may be connected by means of permanent "hard wiring"; flexible armored or nonmetallic shielded copper cable (when local code allow it) or by means of a power supply cord kit. Serial Plate information The serial plate is located as shown.
PAGE 3
Three Conductor Wire Connection to Range If local codes permit connection of the frame grounding conductor to the neutral wire of the copper power supply cord (see Figure 3): 1. Remove the screws from the access plate at the lower right end of the rear cover to expose range terminal connection block. 2.
PAGE 4
Direct Electrical Breaker, Connection Fuse Box to the or Junction Circuit Where local codes DO NOT permit connecting the appliance-grounding conductor to the neutral (white) wire, or if connecting to 4-wire electrical system (see Figure 6): 1. Be sure that no power is supplied on the cable from residence. 2. Follow instructions on previous page for Four Conductor Wire Connection to Range (Fig. 4). 3. In the circuit breaker, fuse box or junction box (Fig.
PAGE 5
. Leveling the Range A. Install an oven rack in the center of the oven. B. Place a level on the rack (see Figure 7). Take 2 readings with the level placed diagonally in one direction and then the other. Level the range, if necessary, by adjusting the 4 leg levelers with a wrench (see Figure 8).
PAGE 6
PAGE 7
Estados Unidos_L_ INSTALAClONY EL SERVIClODEBENSEREFECTUADOSPOR UN INSTALADORCALIFICADO. l IMPORTANTE: GUARDEESTASINSTRUCClONES PARAUSODELINSPECTOR LOCALDEELECTRIClDAD, I , LEA Y GUARDE ESTAS INSTRUCClONES PARA REFERENClA FUTURA. lr_'_ PARA SU SEGURIDAD: No almanece ni utilice gasolina u otros vapores IY liquidos inflamables en la proximidad de este o de cualquier otro artefacto. = Espacios a. b. c.
PAGE 8
= Instale los soportes instrucciones en la p_gina antivuelco. El utilizador es responsable de la conexi6n del cable del suministro el@ctrico al bloque de conexi6n situado detr_qs del panel de acceso. (Vet 4.) 3. Placa de Identificaci6n El electrodom_stico se puede conectar a trav_s de un cableado permanente "cableado duro"; cable de cobre blindado armado o cable no-met_qlico flexible (cuando el c0digo local Io permite) o por medio de un kit de cable de alimentaci6n.
PAGE 9
Conexion del cable de cuatro conductores a la cocina. 1. Retire los tornillos de la parte baja de la cubierta del cable trasero (cubierta de acceso), para tener acceso al bloque de conexi6n del borne terminal. 2. Retire la correa de la base del bloque terminal y del armaz6n del electrodom6stico. Retenga el tornillo de la base. 3.
PAGE 10
Conexion electrica directa al cortacircuito, a la caja de fusibles o la caja de empalmes Si el aparato est_ conectado directamente al cortacircuito, a la caja de fusibles o a la caja de empalmes, use un cable blindado flexible o no metalico recubierto de cobre (con alambre a tierra). Provee una abrazadera releva de anclaje hom61ogo UL a cada extremidad del cable.
PAGE 11
5. C6mo nivelar la estufa 6. Instrucciones para Soporte Antivuelco A. Coloque una parilla del horno en el centro del horno. B. Ponga un nivel sobre la parrilla (Figura 7). Tome dos lecturas con el nivel puesto diagonalmente en una direcci6n y despu6s en la otra. Nivele la estufa, si es necesario, ajustando las 4 patas niveladoras con una Ilave de tuercas (Figura 8).
PAGE 12
6