INSTALLATION INSTRUCTIONS 30" ELECTRIC SLIDE-IN RANGE INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER. IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE. READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. United States Canada FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. Table of Contents Important Safety Instructions .......................................... 2 Product & Cabinet Dimensions...
30" ELECTRIC SLIDE-IN RANGE INSTALLATION INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS This manual contains important safety symbols and instructions. Please pay attention to these symbols and follow all instructions given. This symbol will help alert you to situations that may cause serious bodily harm, death or property damage. This symbol will help alert you to situations that may cause bodily injury or property damage. • Do not store items of interest to children in the cabinets above the range.
0" ELECTRIC SLIDE-IN RANGE INSTALLATION INSTRUCTIONS Product Dimensions Do not install the unit in the cabinet before reading next two pages. Open Door ) (see note 5 Side Panel A. HEIGHT (Under Cooktop) 35 3/4" (90,8 cm) 36 5/8" (93 cm) B. WIDTH C. COOKTOP WIDTH D. TOTAL DEPTH TO FRONT OF RANGE 30" (76,2 cm) 31 1/2" (80 cm) 28 5/16" (71,9 cm) NOTE: 1 2 3 4 5 Do not pinch the power supply cord or the flexible gas conduit between the range and the wall.
30" ELECTRIC SLIDE-IN RANGE INSTALLATION INSTRUCTIONS 30" Min. (76,2 cm) Min. Cabinet Dimensions 13" (33 cm) Countertop hatched surfaces should be flat & leveled. ½" Min. (1,3 cm) Min. Shave Raised Edge To Clear Space for 31½" (80 cm) Wide Cooktop Rim. 30" Min. (See page 3, note 3) (76,2 cm) Min. (See page 3, note 3) 3/8" Min. (0,95 cm) Min. 18" Min. (45,7 cm) Min. 1½" Max. (3,8 cm Max.) ½" Min. (1,3 cm) Min. Approx. 1 7/8" (4,8 cm) 24" Min. (61 cm) Min. Locate Cabinet Doors 1" (2,5 cm) Min.
30" ELECTRIC SLIDE-IN RANGE INSTALLATION INSTRUCTIONS To avoid breakage: Do NOT handle or manipulate the unit by the cooktop. 1 The counter-top around the cut-out should be flat and leveled (see hatched area on illustration 1) 2 3 4 5 6 Before installing the unit, measure the heights of the two (2) cabinet sides (H1-4), front and back (see illustration 1) from the floor to the top of the counter. Shave Raised Edge to Clear Space for a 31½" (80 cm) Wide Cooktop. 1 ½" Max. (3.8 cm Max.
30" ELECTRIC SLIDE-IN RANGE INSTALLATION INSTRUCTIONS 1. Serial Plate Location You will find the model and serial number printed on the serial plate. The serial plate is located as shown. Remember to record the serial number for future reference. Electrical Shock Hazard • Electrical ground is required on this appliance. • Do not connect to the electrical supply until appliance is permanently grounded. • Disconnect power to the circuit breaker or fuse box before making the electrical connection.
30" ELECTRIC SLIDE-IN RANGE INSTALLATION INSTRUCTIONS Four Conductor Wire Connection to Range 5. Electrical Connection to the Where local codes does NOT permit connection of the frame grounding conductor to the neutral wire of the copper power supply cord (see Figure 4): 1. Remove the screw which is fixing the rear wire cover, then remove the rear wire cover (access cover) to expose range terminal connection block (see Figure 2). 2.
30" ELECTRIC SLIDE-IN RANGE INSTALLATION INSTRUCTIONS Direct Electrical Connection to the Circuit Breaker, Fuse Box or Junction Box Green (or Bare Copper) Wire If the appliance is connected directly to the circuit breaker, fuse box or junction box, use flexible, armored or nonmetallic sheathed copper cable (with grounding wire). Supply a U.L. listed strain-relief at each end of the cable. At the appliance end, the cable goes through the Direct Connection Hole (see Figure 4) on the Cord Mounting Plate.
30" ELECTRIC SLIDE-IN RANGE INSTALLATION INSTRUCTIONS adjustments to make the top flat should be made or gaps between the countertop and the range cooktop may occur. • Countertop must be level. Place a level on the countertop, first side to side, then front to back. If the countertop is not level, the range will not be level. The oven must be level for satisfactory baking results. Cooktop sides of range fit over edges of countertop opening 7.8 7.9 Position range in front of the cabinet opening. 7.
30" ELECTRIC SLIDE-IN RANGE INSTALLATION INSTRUCTIONS 6. After leveling the range, the rear leveling legs (located beside the rear wheels) must be lowered almost to the floor level (leave a small gap). This is necessary to secure the unit to the anti-tip bracket. 7.9 Position range in front of the cabinet opening. 7.10 7.11 7.12 Make sure that the glass which overhangs the countertop clears the countertop. If necessary, raise the unit by lowering the leveling legs. Level the range (see section 8).
30" ELECTRIC SLIDE-IN RANGE INSTALLATION INSTRUCTIONS Refer to the Use and Care Guide packaged with the range for operating instructions and for care and cleaning of your range. Convection (some models)–When the oven is set to CONV. BAKE/ROAST at 350°F (177°C), the convection element cycles on and off and the convection fan turns. The convection fan will stop turning when the oven door is opened during convection baking or roasting. Do not touch the elements. They may be hot enough to cause burns.
30" ELECTRIC SLIDE-IN RANGE INSTALLATION INSTRUCTIONS 1. Draw a center line (CL) on the floor where the range should be installed. Also draw a line on the floor at the range back position if there is no wall. 2. Unfold paper template and place it flat on the floor with the right rear corner positioned exactly on the intersection of the center and back lines you just drew before. (Use the diagram below to locate brackets if template is not available. (Figure 11)) 3.
30" ELECTRIC SLIDE-IN RANGE INSTALLATION INSTRUCTIONS C. Level and position the range - Slide range to its final position. Insert the range leveling leg in the anti-tip bracket. Visually verify if the anti-tip bracket is engaged. Lower the range by adjusting the 4 leveling legs alternatively until the range is level. Check if the range is level by placing a spirit level on the oven rack. Take 2 readings with the spirit level placed diagonally; take a reading in one direction and then in the other direction.
INSTRUCCIONES DE INSTALACIÓN ESTUFA ELÉCTRICA EMPÓTRALES DE 30" LA INSTALACIÓN Y EL SERVICIO DEBEN SER EFECTUADOS POR UN INSTALADOR CALIFICADO. IMPORTANTE: GUARDE ESTAS INSTRUCCIONES PARA USO DEL INSPECTOR LOCAL DE ELECTRICIDAD. LEA Y GUARDE ESTAS INSTRUCCIONES PARA REFERENCIA FUTURA. Estados Unidos Canada PARA SU SEGURIDAD: No almacene ni utilice gasolina u otros vapores y líquidos inflamables en la proximidad de este o de cualquier otro artefacto.
INSTRUCCIONES DE INSTALACIÓN PARA LA ESTUFA ELÉCTRICA DESLIZABLE DE 30" IMPORTANTES INSTRUCCIONES DE SEGURIDAD Este manual contiene importantes mensajes de seguridad. Siempre lea y obedezca todo mensaje de seguridad. Indica una situación muy peligrosa, la cual de no ser evitada puede ocasionar graves heridas y hasta la muerte. Indica una situación de peligro inminente, la cual de no ser evitada puede ocasionar heridas leves o daños al producto solamente.
INSTRUCCIONES DE INSTALACIÓN PARA LA ESTUFA ELÉCTRICA DESLIZABLE DE 30" Dimensiones de la unidad No instale la unidad en el gabinete si no ha leído esta página. rta Puerta abie ) (vea nota 5 Panel Lateral A. ALTURA (Debajo de la cubierta) 35 3/4" (90,8 cm) 36 5/8" (93 cm) B. ANCHURA C. ANCHURA DE LA PLANCHA DE COCINAR D.
INSTRUCCIONES DE INSTALACIÓN PARA LA ESTUFA ELÉCTRICA DESLIZABLE DE 30" 30" Min. (76,2 cm) Min. Dimensiones de la Gabinete 13" (33 cm) Estas superficies deben de ser planas y niveladas (área rayada). 30" Min. (76,2 cm) Min. (Vea Nota 3, de la pagina 16) ½”min. Lije la parte elevada del borde para obtener las 31½" (80 cm) de ancho del reborde de la plancha de cocinar. 18" Min. (45,7 cm) Min. 3/8”min. 1½" Max. (3,8 cm Max.) E ½”min. Approx. 1 7/8" (4,8 cm) G 24" Min. (61 cm) Min.
INSTRUCCIONES DE INSTALACIÓN PARA LA ESTUFA ELÉCTRICA DESLIZABLE DE 30" Para evitar fractura de la unidad: NO manipule la unidad sosteniendo la cubierta. 1 La cubierta alrededor del espacio donde usted instalara su unidad debe de estar plana y nivelada. (Vea el área sombreada en la ilustración número 1) 2 3 4 5 6 7 Antes de instalar la unidad, mida la altura de los dos (2) lados de los gabinetes (H1-4), frente y parte trasera (vea ilustración 1) del piso a lo alto de la cubierta.
INSTRUCCIONES DE INSTALACIÓN PARA LA ESTUFA ELÉCTRICA DESLIZABLE DE 30" Para casas sobre ruedas, nuevas instalaciones, en los vehículos de recreativos o en las lugares donde los códigos locales no permiten la conexión del conductor de tierra al neutro, un ensamble de suministro eléctrico de 3 (cuando códigos locales permitan conexión a tierra) o 4 conductores para estufas, calificado a 125/250 voltios mínimo, 50 Amperes recomendados (40 Amperes mínimo) debe de ser utilizad.
INSTRUCCIONES DE INSTALACIÓN PARA LA ESTUFA ELÉCTRICA DESLIZABLE DE 30" Conexión del cable de cuatro conductores a la cocina. Este electrodoméstico fue fabricado con el marco aterrizado a través de un puente de conexión entre el neutral de la fuente de alimentación y el marco. Si es utilizado en los E.E. U.U.
INSTRUCCIONES DE INSTALACIÓN PARA LA ESTUFA ELÉCTRICA DESLIZABLE DE 30" Conexión eléctrica directa al cortacircuito, a la caja de fusibles o la caja de empalmes Si el aparato está conectado directamente al cortacircuito, a la caja de fusibles o a la caja de empalmes, use un cable blindado flexible o no metálico recubierto de cobre (con alambre a tierra). Provee una abrazadera de alivio de esfuerzo homólogo UL a cada extremidad del cable.
INSTRUCCIONES DE INSTALACIÓN PARA LA ESTUFA ELÉCTRICA DESLIZABLE DE 30" • El mostrador deber ser nivelado. Coloque un nivelador sobre el mostrador, primero de lado a lado y luego del frente hacia atrás. Si el mostrador no está nivelado, la cocina no estará nivelada. El horno debe ser nivelado para tener resultados satisfactorios al hornear. Las extremidades de la plancha de la cocinar sobrepasan los bordes de la abertura del mostrador. 7.8 7.9 Coloque la cocina enfrente de la abertura del armario. 7.
INSTRUCCIONES DE INSTALACIÓN PARA LA ESTUFA ELÉCTRICA DESLIZABLE DE 30" 7.11 7.12 6. Después de nivelar la unidad, las patas traseras (localizadas al lado de las ruedas), debe de bajarse casi hasta el nivel del suelo (deje un pequeño espacio). Este es necesario para asegurar la unidad con el fijación anti-inclinación. Nivele la cocina (vea Nivelación de la estufa). El piso donde se instala la cocina debe estar nivelado.
INSTRUCCIONES DE INSTALACIÓN PARA LA ESTUFA ELÉCTRICA DESLIZABLE DE 30" Convección/Convection (algunos modelos)– Cuando el horno se pone a CONV. BAKE/ROAST a 350°F (177°C), los dos elementos se enciendan y se apagan alternando en un ciclo y el ventilador se pone en marcha. El ventilador de convección se parará cuando se abre la puerta del horno durante el cocido o el asado por convección. 9.
INSTRUCCIONES DE INSTALACIÓN PARA LA ESTUFA ELÉCTRICA DESLIZABLE DE 30" 1. Dibujar una línea central en el piso donde se instalará la cocina. Si no hay pared posterior, dibujar otra línea en el piso que corresponda a la parte posterior de la cocina. 2. Desplegar el molde de papel y colocarlo alisado sobre el piso con el vértice posterior derecho posicionado exactamente en la intersección de las líneas central y posterior dibujadas anteriormente.
INSTRUCCIONES DE INSTALACIÓN PARA LA ESTUFA ELÉCTRICA DESLIZABLE DE 30" C. Nivele la cocina y coloque la cocina en su lugar. Deslice la estufa a su lugar. Colocar la pata niveladora dentro de la fijaciones de anti-inclinación. Verifique visualmente que las fijaciones de anti-inclinación estén correctamente enganchados (anclados). Nivele la cocina. Nivele la estufa si es necesario, ajustando las 4 patas niveladoras con una llave ajustable.
INSTRUCTIONS D'INSTALLATION CUISINIÈRE ENCASTRABLE ÉLECTRIQUE DE 30" L’INSTALLATION ET L’ENTRETIEN DOIVENT ÊTRE EFFECTUÉS PAR UN INSTALLATEUR QUALIFIÉ. IMPORTANT: CONSERVEZ POUR L’INSPECTEUR D’ÉLECTRICITÉ LOCAL. LISEZ ET CONSERVEZ CES INSTRUCTIONS POUR RÉFÉRENCES ULTÉRIEURES. United States Canada POUR VOTRE SÉCURITÉ : N’entreposez pas ou n’utilisez pas d’essence ou d’autres produits inflammables à proximité de cet appareil ou de tout autre appareil électroménager.
INSTRUCTIONS D'INSTALLATION POUR LA CUISINIÈRE 30" ENCASTRABLE INSTRUCTIONS DE SÉCURITÉ IMPORTANTES Ce guide contient des instructions et symboles de sécurité importants. Veuillez faire particulièrement attention à ces symboles et suivre les instructions données. Ce symbole vous prévient des situations qui risquent d’entraîner de graves blessures, la mort ou des dommages matériels. Ce symbole vous prévient des situations pouvant entraîner des blessures ou dommages matériels.
INSTRUCTIONS D'INSTALLATION POUR LA CUISINIÈRE 30" ENCASTRABLE Dimensions du produit Ne pas insérer l'unité dans le comptoir sans avoir lu les deux prochaines pages. rte Porte ouve ) 5 (voir la note Panneau latéral A. HAUTEUR (Sous la table de cuisson) 35 3/4" (90,8 cm) 36 5/8" (93 cm) B. LARGEUR C. LARGEUR DE LA TABLE DE CUISSON D.
INSTRUCTIONS D'INSTALLATION POUR LA CUISINIÈRE 30" ENCASTRABLE Dimensions du comptoir 30" Min. (76,2 cm) Min. 13" (33 cm) Ces surfaces doivent être planes et à niveau (région hachurée). ½" Min. (1,3 cm) Min. Arasez le dessus du comptoir à au moins 31 1/2" (80 cm) de largeur pour la cuisinière. 30" Min. (Voir la note 3 à la page 29) (76,2 cm Min.) (Voir la note 3 à la page 29) 3/8" Min. (0,95 cm) Min. 18" Min. (45,7 cm) Min. 1 ½" Max. (3,8 cm Max.) ½" Min. (1,3 cm) Min. Approx.
INSTRUCTIONS D'INSTALLATION POUR LA CUISINIÈRE 30" ENCASTRABLE Pour éviter les cassures: NE PAS manipuler l'appareil par la table de cuisson vitrifiée. 1 Le comptoir alentour de l'ouverture de découpage doit être plat et à niveau (voir hachures sur illustration 1). 2 Avant d'installer l'appareil, mesurer les hauteurs des deux (2) côtés du comptoir (H1-4), avant et arrière (voir illustration 1) du plancher jusqu'au dessus du comptoir. 3 Arasez le dessus du 1 ½" Max. comptoir à (3,8 cm Max.
INSTRUCTIONS D'INSTALLATION POUR LA CUISINIÈRE 30" ENCASTRABLE (40A minimum). Le cordon doit soit avoir 3 (lorsque le code local permet la mise à terre par le neutre) ou 4 conducteurs. Les bornes aux extrémités des câbles doivent comporter soit une boucle fermée, soit des cosses à fourches ouvertes et aux extrémités renversées. Le cordon doit être muni d'un réducteur de tension. 1.
INSTRUCTIONS D'INSTALLATION POUR LA CUISINIÈRE 30" ENCASTRABLE Pour une connexion à un câble d'alimentation à quatre conducteurs (maisons mobiles) (États-Unis) 5. Connexions électriques à la cuisinière (U.S.A.) Pour une connexion à un câble d'alimentation à trois conducteurs (EtatsUnis seulement) Si les codes locaux ne permettent PAS la connexion du conducteur de mise à la terre du châssis au fil neutre du cordon d'alimentation en cuivre (voir figure 4). 1.
INSTRUCTIONS D'INSTALLATION POUR LA CUISINIÈRE 30" ENCASTRABLE Câble d'alimentation Connexions électriques au système électrique de la résidence Fil dénudé L'appareil doit être raccordé directement au disjoncteur ou au compartiment de fusibles au moyen d'un câble flexible en cuivre, blindé ou muni d'une gaine protectrice non métallique (avec fil de mise à la terre). Un des connecteurs homologués UL doit être fixé à chaque extrémité du câble d'alimentation (à l'appareil et à la boîte de jonction).
INSTRUCTIONS D'INSTALLATION POUR LA CUISINIÈRE 30" ENCASTRABLE • Le dessus de comptoir doit être à niveau. Placez un niveau sur le dessus de comptoir, d’abord de chaque côté, et ensuite du devant à l’arrière. Si le dessus de comptoir n’est pas horizontal, la cuisinière ne le sera pas non plus. Le four doit être à l’horizontal pour obtenir des résultats de cuisson satisfaisants.
INSTRUCTIONS D'INSTALLATION POUR LA CUISINIÈRE 30" ENCASTRABLE 7.10 7.11 7.12 5. S'il est impossible de mettre à niveau l'appareil, contactez un menuisier pour corriger les défauts dans le plancher. Assurez-vous que la surface de cuisson vitrifiée allant par dessus le comptoir est bien plus haute que le comptoir. Si tel n'est pas le cas, levez l'appareil en baissant les pattes de nivellement. Nivelez la cuisinière (voir la section 8). Le plancher qui supporte la cuisinière doit être de niveau.
INSTRUCTIONS D'INSTALLATION POUR LA CUISINIÈRE 30" ENCASTRABLE Convection (certains modèles)– Lorsque le four est réglé à CONV. BAKE/ROAST à 350°F (177°C), l'élément convection se met à chauffer et le ventilateur de convection se met à tourner. Le ventilateur de convection arrête de tourner lorsque la porte du four est ouverte durant la cuisson par convection. Tiroir-réchaud (certains modèles)–Tournez le bouton d'ajustement à ÉLEVÉ (HI) et vérifiez si le tiroir chauffe. 9.
INSTRUCTIONS D'INSTALLATION POUR LA CUISINIÈRE 30" ENCASTRABLE câblage électrique. Les vis fournies fonctionneront aussi bien dans du bois que dans du béton. 1. Dessinez une ligne au sol (à l'avant de l'ouverture) en ligne avec le devant des armoires (et non en ligne avec le retour d'armoire). 2.
INSTRUCTIONS D'INSTALLATION POUR LA CUISINIÈRE 30" ENCASTRABLE C. Mise à niveau et positionnement de la cuisinière. Glissez la cuisinière à son emplacement final. Insérez la patte de nivellement de la cuisinière dans le support. Assurez-vous que la patte de la cuisinière est bien insérée dans le support en vérifiant visuellement. Placez un niveau à bulle sur l’une des grilles de l’appareil pour vérifier s’il est de niveau.
NOTES