Welcome & CongratUlations ......... Before Setting Surface Controls, Setting Surface Controls .......................... www,frigidaire.com USA 1-800-944-9044 www,frigidaire.ca Canada 1-800-265-8352 .........
iil Product Registration Register Your Product ThePRODUCT REGISTRATION CARD should be filled in completely, signed and returned to Electrolux Home Products. Congratulations on your purchase of a new appliance! At Electrolux Home Products, we are very proud of our product and are completely committed to providing you with the best service possible. Your satisfaction is our number one priority. We know you'll enjoy your new appliance and Thank You for choosing our product.
Read all instructions before using this appliance. Save these instructions for future reference. If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death. FOR YOUR SAFETY -- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. -- WHAT TO DO IF YOU SHELL GAS: • Do not try to light any appliance.
• DO NOT TOUCH SURFACE BURNERS, GRATES, OR AREAS NEAR THESE BURNERS. Surface burners may be hot even though the flames are not visible. Areas near surface burners may become hot enough to cause burns. During and after use, do not touch or let clothing or other flammable materials touch these areas until they have had sufficient time to cool. Among these areas are the cooktop and the surfaces facing the cooktop.
GROUNDING INSTRUCTIONS For personal safety, the cooktop must be properly grounded. For maximum safety, the power cord must be plugged into an electrical outlet that is correctly polarized and properly grounded. DO NOT operate the cooktop using a 2-prong adapter or an extension cord. If a 2-prong wall receptacle is the only available outlet, it is the personal responsibility of the consumer to have it replaced with a properly grounded 3-prong wall receptacle installed by a qualified electridan.
LOCATIONS OF THE GAS SURFACE ASSEMBLY OF THE BURNER GRATES The SIMMER burner is best used for simmering delicate sauces, etc. This burner is located at the right rear burner position. It is very important to make sure that all of the Surface Burner Caps and Surface Burner Grates are installed correctly and at the correct locations. :_ Remove all packing material from cooktop area. 2 Discard all packing material (if applicable). 3 Unpack Burner Grates and position on the cooktop (see Figure 3 or 4).
OPERATING THE GAS SURFACE CONTROLS 1 Place cooking utensil on surface burner. 2 Push the surface control knob down and turn counterclockwise out of the OFF position. 3 Release the knob and rotate to the LITE position (see figure 1). Note: All four electronic surface ignitors will spark at the same time. However, only the burner you are turning on will ignite. 4 Visually check that the burner has a flame. 5 Turn the control knob counterclockwise to the desired flame size.
CLEANING VARIOUS PARTS OF YOUR COOKTOP Before cleaning any part of the cooktop, be sure all controls are turned OFF and the cooktop is COOL. REMOVE SPILLOVERS AND HEAVY SOILING AS SOON AS POSSIBLE. REGULAR CLEANING WILL REDUCE THE NUMBER OF MAJOR CLEANING LATER. Aluminum (Trim Pieces) & Use hot, soapy water and a cloth. Dry with a clean cloth.
CLEANING & BURNER THE COOk'TOPr GRATES BURNER CAPS The cooktop is designed to make cleaning easier. Because the gas Burners are sealed, deanups are easy when spillovers are cleaned up immediately. The cooktop, Burner Heads and Caps should be routinely cleaned. Keeping the Burner Head Ports clean will prevent improper ignition and an uneven flame. Refer to the following instructions: THE COOl(TOP IS NOT REMOVABLE. Do not Pay attention to not damage electrodes.
CLEANING RECOHHENDATIONS CERAMIC GLASS COOKTOP FOR THE Before cleaning the cooktop, be sure the controls are turned to OFF and the cooktop is COOL. Plastic or foods with a high sugar content" These types of soils need be removed immediately if spilled or melted onto the ceramic cooktop surface. Permanent damage (such as pitting of the cooktop surface) may occur if not removed immediately.
Before you call for service, review this list. It may save you time and expense. The list includes common occurrences that are not the result of defective workmanship or materials in this appliance. Surface burners do not light, Surface Control knob has not been completely turned to LITE. Push in and turn the Surface Control knob to LITE until burner ignites and then turn control to desired flame size. Be sure gas supply valve is open. Burner ports or slots are clogged.
Your appliance is covered by a one year limited warranty. For one year from your original date of purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed, used and maintained in accordance with the provided instructions.
