Product Specifications Sheet

Built-In Microwave with 27" or 30" Trim Kit
(Side Controls - 2.2 cu.ft.)
Professional and Gallery
24
7
/16"
19
5
/8"
Power cord
location (right
top rear)
13
5
/8"
rear
extrusion
120V / 60Hz
grounded outlet
20" min.
4"
6"
4"
24
3
/4" min.
25" max.
Bottom Duct Assembly
Outlet should NOT
be located within
shaded area UNLESS
cabinet depth is
greater than 21"
16
3
/4" min.
17" max.
Allow at least
21" clearance for door
depth when open
1
1
/2"
30"
or 27"
Trim Kit Faceplate
18"
(30") 30"
(27") 27"
*Note: When used in combination with
another Frigidaire
®
built-in product, a
minimum clearance of 3" required from
bottom of Built-In Microwave cutout to top
edge of companion product’s faceplate,
leaving a 2
1
/8" visible gap between both
product faceplates
**Minimum cabinet width
required for installation
with optional 30" Trim Kit.
27" minimum cabinet width
required for installation
with optional 27" Trim Kit.
30" min.**
20"
min.
Trim Kit –
7
/8" faceplate
overlap
16
3
/4" min.
17" max.
Full plywood
base required to
support 100 lbs.
24
3
/4" min.
25" max.
2
1
/8"
(visible
gap)*
INSTALLATION SPECIFICATIONS
•
Product Shipping Weight (Approx.) – 49 Lbs. (not incl. Trim Kit)
•
Voltage Rating – 120V / 60 Hz / 15 Amps
•
Connected Load (kW Rating) @ 120 Volts = 1.7 kW
(For use on adequately wired 120V, dedicated circuit having 2-wire service
with a separate ground wire. Appliance must be grounded for safe operation.)
•
Amps @ 120 Volts = 14.2 Amps
•
Always consult local and national electric codes.
•
Microwave can stand alone on countertop or be built in with optional 30"
or 27" Trim Kit (ordered by individual part number) which includes Bottom
Duct Assembly – shipped in separate box.
•
Allow 21" minimum clearance for 90° door swing.
•
Minimum 20" deep oven cutout dimension is critical for proper installation for
oven and faceplate to fit flush against cabinet front.
•
Consult local building code, in the event that cutout opening may be required
to be enclosed with sides, ceiling and rear partition.
•
Full oven base of solid plywood or similar material required, capable of
supporting 100 Lbs.
•
Base must be level and front of cabinet square for proper operation.
•
Grounded outlet should NOT be located in shaded area, as indicated, UNLESS
cabinet depth is greater than 21”.
•
Can NOT be installed above any gas wall oven.
•
Built-In Microwave is approved to be used in combination with any Frigidaire®
Electric Single Wall Oven and /or Warmer Drawer. (Refer to model-specific
Combination Installation Specification pages on web.)
•
When used in combination with another Frigidaire® built-in product, a
minimum clearance of 3" required from bottom of Built-In Microwave cutout
to top edge of companion product’s faceplate, leaving a 2-1/8" visible gap
between both product faceplates.
OPTIONAL ACCESSORIES
•
30" Black Stainless Steel Trim Kit – (PN # MWTK30FGUD).
•
27" Black Stainless Steel Trim Kit – (PN # MWTK27FGUD).
•
30" Stainless Steel Trim Kit – (PN # MWTK30FGUF).
•
27" Stainless Steel Trim Kit – (PN # MWTK27FGUF).
Specifications subject to change. Accessories information available on the web at frigidaire.com
Note: For planning purposes only. Always consult local and national electric, gas and plumbing codes.
Refer to Product Installation Guide for detailed installation instructions on the web at frigidaire.com.
USA
•
10200 David Taylor Drive
•
Charlotte, NC 28262
•
1-800-FRIGIDAIRE
•
frigidaire.com
CANADA
•
5855 Terry Fox Way
•
Mississauga, ON L5V 3E4
•
1-800-265-8352
•
frigidaire.ca
FGMO226NU 08/18
© 2018 Electrolux Home Products, Inc.
FGMO226NU D/F
MICROWAVE
24" BUILT-IN