All about the Installation and Use & Care Telescoping Downdraft Ventilation System of your Welcome & Congratulations....................................2 Installation............................................................9 Important Safety Instructions..................................3 Use & Care..........................................................13 Shipping Pack........................................................4 Before You Call....................................................
WELCOME & CONGRATULATIONS Product Registration Register Your Product The PRODUCT REGISTRATION CARD should be filled in completely, signed and returned to Electrolux Home Products. Serial Plate Location Serial Plate Location Please record your model and serial numbers below for future reference. Model Number: Congratulations on your purchase of a new appliance! At Electrolux Home Products, we are very proud of our product and are completely committed to providing you with the best service possible.
IMPORTANT SAFETY INSTRUCTIONS Read all instructions before using this appliance. Save these instructions for future reference. DEFINITIONS This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: • Use this unit only in the manner intended by the manufacturer.
SHIPPING PACK Stabilizing Brackets Instruction Manual Cutout Template Warranty Card Telescoping Downdraft Duct Transition Tools You Will Need • Phillips Screwdriver • 1/4” Nut Driver / Ratchet • Tape Measure • Carpenter Square • Vertical Level or Plum Line • Tools required to cut countertop 4 IMPORTANT Retain all packing and materials until the telescoping downdraft and all components have been installed.
PRODUCT DIMENSIONS Downdraft Top Trim A E Rise 1 7/16” (3.6 cm) ent pic V co Teles 2 1/4” (5.7 cm) sis Chas ng i Hous C D 11 /16” (29.0 cm) 7 r lowe B rol Cont Box B Model A B C D E Rise FH30DD50MS 30” (76.2 cm) 26 /8” (68.3 cm) FH36DD50MS 36” (91.4 cm) 32 /8” (83.6 cm) 17 13/16” (45.2 cm) 34 5/16” (87.2 cm) 2 3/16” (5.5 cm) 10” (25.4 cm) 7 7 Cutout Dimensions 26 15/16” [+ 1/16” / - 0”] (68.4 - 68.6 cm) Cooktop Edge Cutout width for 30” model 32 15/16” [+ 1/16” / - 0”] (83.
PLANNING Basic Information Take Measurements A qualified technician must complete the installation of this appliance. This downdraft blower system is designed to be used to exhaust airborne contaminants when cooking with a variety of gas, electric or induction cooktops. It can be mounted in island, peninsula, or conventional wall locations. This unit is installed following these basic steps: • Cut out the countertop opening. • Mount the unit in the cabinet. • Connect the ductwork and electrical.
PLANNING Plan the Ductwork This downdraft blower system is designed for use with 3¼ x 10” ductwork (can be transitioned to 6” round). For best performance, choose the ducting option which allows the shortest length of ductwork and a minimum number of elbows and transitions. The system will operate most efficiently when the ductwork does not exceed 60 feet of equivalent duct. The downdraft will operate properly with ductwork up to 100 equivalent feet of duct. See page 12 for Calculated Duct Length Table.
PLANNING Plan the Electrical Connection The downdraft blower system draws 2.8 AMPS and requires a 120 VAC, 60 Hz circuit. The unit has a 28 inches long power cord with a 3 pronged plug. Plan to provide a grounded outlet in a location which will allow the unit’s power cord to reach. M 9-1/2" (24.1cm) 23-3/4” (60.3 cm) 22-1/8" (56.2 cm) NOTE If the 30” model is being installed in a 30” wide cabinet or the 36” model in a 36” wide cabinet, the outlet cannot be located on the back wall of cabinet.
INSTALLATION 1. Cut Countertop Opening - Lay out and cut the cooktop cut-out far enough forward so downdraft will fit behind it (refer to cooktop installation instructions). - Set cooktop in place and slide it as far forward as possible. Center and square it with edges of countertop. A ½” minimum clearance behind cutout must be maintained for proper installation. 3. Prepare the Downdraft Blower System Duct Connection The downdraft is shipped with blower oriented for exhaust discharge down.
INSTALLATION 4. Install Duct Transition to Blower Install the duct transition on the blower, using the three wide head Phillips screws. It is recommended for all duct joints, the seam between the blower and the duct transition should be sealed with duct tape over the screws. of the cabinet so that the vent chassis housing is vertical, check the level of the vent on both the right and left sides, and tighten the screws.
INSTALLATION 6. Install Ductwork - Use galvanized or aluminum duct in 6” round or 3 ¼” x 10” size, or a combination of both. PVC duct should be used if installing under a poured concrete slab. Use the shortest and straightest duct run possible. The system will operate most efficiently when the ductwork does not exceed 60 feet of equivalent duct. The downdraft will operate properly with ductwork up to 100 equivalent feet of duct. See page 12 for Calculated Duct Length Table.
INSTALLATION Calculating Duct Length Table For maximum efficiency, use the shortest and straightest duct possible. The system will operate most efficiently when the ductwork does not exceed 60 feet of equivalent duct. The downdraft will operate properly with ductwork up to 100 equivalent feet of duct. Calculations are approximate and based on HVAC industry standards. DUCT PIECES 6" (15.2cm) Round Straight ** EQUIVALENT LENGTH X NUMBER USED = 1 Ft. (0.3m) Ft. or m 1.5 Ft. (0.45m) Ft. or m 6" (15.
USE & CARE Operating the Telescoping Downdraft System - Raise the downdraft by pressing the raise/lower push button. The telescoping vent will rise up to full height. - The blower can also be turned off by simply pressing the raise/lower push button and lowering the telescoping vent. - The blower can then be turned on by sliding the control knob up. - The blower speed can be adjusted by sliding the control knob between the Hi and Lo positions.
USE & CARE Cleaning the Telescoping Downdraft Vent WARNING It is advised to disconnect power from the downdraft when cleaning to minimize risk of electrical shock or damaging the appliance due to spills onto electrical components. CAUTION Before cleaning the telescoping downdraft make sure the cooktop is Off and all surfaces are cool. Daily: Wipe spills and spatters from the telescoping downdraft vent and trim as advised below.
BEFORE YOU CALL (Solutions to Common Problems) IMPORTANT Before you call for service, review this list. It may save you time and expense. The list includes common occurrences that are not the result of defective workmanship or materials in this appliance. OCCURRENCE POSSIBLE CAUSE/SOLUTION Telescoping Vent does not fully raise Check for and remove obstructions. The telescoping vent is designed to tilt and stop with obstructions.
MAJOR APPLIANCE WARRANTY Your appliance is covered by a one year limited warranty. For one year from your original date of purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed, used and maintained in accordance with the provided instructions.