mr USA 1-800-944-9044 www.frigidaire.com Canada 1-800-265-8352 www.frigidaire.
CONTENTS Thank you for choosing Frigidaire. Important Safety Instructions ............................... List of materials ................................................... Electrical requirements ......................................... Location requirements .......................................... Product dimensions .............................................. 3 5 5 6 6 Venting Requirements .......................................... Prepare the location ........................................
Read all instructions before using this appliance. Save these instructions for future references Approved for residential appliances For residential use only Do not attempt to install or operate your appliance until you have read the safety precautions in this manual. Safety items throughout this manual are labeled with a WARNING or CAUTION based on the risk type. _This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
To Reduce The Risk Of Fire Or Electric Shock, Do Not Use This Hood With Any External Solid State Speed Control Device. TO REDUCE THE _SK OF A RANGE TOP GREASE FIRE. a)Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings. b)AIways turn hood ON when cooking at high heat or when flambeing food (I.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambe'). c) Clean ventilating fans frequently.
LIST OF MATERIALS ELECTRICAL Parts included in your hood • 4 - 0.45 x 1.3 cm mounting screws • 31/4" x 10" (8.3 x 25.4 cm) rectangular metal vent system. NOTE: An optional 7" round duct kit is available. You can order this kit as part number 5304487139. Observe all governing codes and ordinances. Ensure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.
Cabinet Dimensions Observe all governing codes and ordinances. • It is the installer's responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located inside the range hood on the left side (See page 2 for location). Range hood location should be away from strong draft areas, such as windows, doors and strong heating vents. • Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance.
• Vent system must terminate to the outdoors. • Do not terminate the vent system into an attic or other enclosed area. • Do not use a 4" (10.2 cm) laundry-type wall cap. • Use a 31/4" x 10" (8.3 x 25.4 cm) rectangular metal vent. Rigid metal vent is recommended. Plastic or metal foil vent is not recommended. • The length of vent system and number of elbows should be kept to a minimum to provide efficient performance. For the most efficient and quiet operation: • Use no more than three 90 ° elbows.
PREPARE THE LOCATION 31/4' ' x 10" (8.3 cm x 25.4 cm) Vent System Vent Piece 31/4" x 10" (8.3 cm x 25.4 cm) 90 ° elbow 5.0 ft (1.5 m) 31/4" x 10" (8.3 cm x 25.4 cm) flat elbow 12.0 ft (3.7 m) 31/4" x 10" (8.3 cm x 25.4 cm) wall cap 0.0 ft (0.0 m) Example Vent System 31/4" (8.3 x x 25.4 Before making cutouts, make sure there is proper clearance within the ceiling or wall. 1. Disconnect power. 2.Select a fiat surface for assembling the range hood. Place covering over that surface. 3.
To wire through top: 2.Mark a line distance (A) from the right of the centerline on the underside of the cabinet. Mark the point on this line that is 7/8" (2.2 cm) from back wall. Drill a 11/4" (3.2 cm) diameter hole (B) through the cab net at this point. I I .... 'i!_I__A B 7/8"(2.2cm) /I] Style 2 - Cut Openings for 31/4" x 10" (8.3 cm x 25.4 cm) Rectangular Vent System Roof Venting To make a 4"x 101/2" (10.16 cm x 26.
Style 3 - Cut Openings for 31/4" x 10" (8.3 x 25.4 cm) Rectangular Vent Transition to Round Vent Roof Venting To make a circular vent opening on the underside of the cabinet top: 1,Mark a centerline on the underside of the top of cabinet. 2,Mark a line 5" (12.7 cm) from the back wall on the underside of the top of cabinet. 3,Use a compass or a circle template to draw a circle with a diameter of 71/2" (19 cm). Use saber or keyhole saw to cut the circular vent opening.
Use 1//, (3 mm) drill bit and drill 4 pilot holes as shown. NOTE: Make the drill holes on the thin area of the slot. A. Drill pilot hole A 3.Install the 4 - .45 cm x 1.3 cm mounting screws in pilot holes. Leave about 1/4"(6.4 mm) space between screw heads and cabinet to slide range hood into place. \\\\_\\\\ _- 1/4" (6.4 mm) 4.For roof installations, remove the top rectangular vent knockout. For wall installations, remove the rear rectangular vent knockout. Power Supply Cable Installation 1.
MAKE ELECTRICAL CONNECTION INSTALL RANGE HOOD (Recirculating Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock. 1. Disconnect power. C D. A ...... _ E A.White wires B. Black wires C. UL listed wire connector D. Green (or bare) ground wire E. Home power supply cable F. UL listed or CBA approved I/2" strain relief version) 1.
3.Remove the power supply knockout from the top or rear of the vent hood (depending on the incoming location of your home power supply cable) and install a UL listed or CSA approved 1/2" strain relief. A RANGE HOOD USE The range hood is designed to remove smoke, cooking vapors and odors from the cooktop area. For best results, start the hood before cooking and allow it to operate several minutes after the cooking is complete to clear all smoke and odors from the kitchen.
Cleaning 4.Replace screw in the filter retainer. 5.To clean grease filter, soak the filters in hot water using To Reduce The Risk Of Fire Or Electrical shock a mild detergent. Rinse well disconnect from power supply before cleaning. and shake to dry. Or place in upper rack of dishwasher A.Filterscrew to clean. NOTE: Do not use ammoClean the hood and grease filters frequently nia. The aluminum on the grease filter will corrode and according to the following instructions. Replace darken.
Problem Possible Causes Solutions After installation, the unit doesn't 1. The power line and the cable locking connector is not connecting properly, 1. Check the power connection with the unit is connected properly. work. 2. The wires from the switches are disconnected 2. Make sure the wires on the switches are or loose, connected properly. Light works, 1. The motor is defective, possible seized. 1. Change the motor. but motor is not turning, 2.
Warranty Your appliance is covered by a one year limited warranty. For one year from your original date of purchase, Electrolux will repair or replace any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed, used, and maintained in accordance with the provided instructions.
printed in Mexico FRIGIDAIR
