mr USA 1-800-944-9044 www.ffigidai_.com Canada 1-800-265-8352 www.ffigidaire.
CONTENTS Important Safety Instructions ............................... List of materials ................................................... Electrical requirements ......................................... Location requirements .......................................... Product dimensions .............................................. 3 5 5 6 6 Venting Requirements .......................................... Prepare the location .............................................
Read all instructions before using this appliance. Save these instructions for future references Approved for residential appliances For residential use only Do not attempt to install or operate your appliance until you have read the safety precautions in this manual. Safety items throughout this manual are labeled with a WARNING or CAUTION based on the risk type. _This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
To Reduce The Risk Of Fire Or Electric Shock, Do Not Use This Hood With Any External Solid State Speed Control Device. TO REDUCE THE _SK OF A RANGE TOP GREASE FIRE. a)Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings. b)AIways turn hood ON when cooking at high heat or when flambeing food (I.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambe'). c) Clean ventilating fans frequently.
LIST OF MATERIALS ELECTRICAL Parts included in your hood • 4 - 0.45 x 1.3 cm mounting screws • 2 - .35 x .65 cm rectangular vent transition mounting screws • 2 - .29 x .65 cm round metal mounting plate mounting screws • 31/4" x 10" (8.3 x 25.4 cm) rectangular metal vent system. • 7" (17.8 cm) round metal mounting plate. Observe all governing codes and ordinances.
Cabinet Dimensions Observe all governing codes and ordinances. • It is the installer's responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located inside the range hood on the left side (See page 2 for location). Range hood location should be away from strong draft areas, such as windows, doors and strong heating vents. • Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance.
• Vent system must terminate to the outdoors. • Do not terminate the vent system into an attic or other enclosed area. • Do not use a 4" (10.2 cm) laundry-type wall cap. • Use a 31/4" x 10" (8.3 x 25.4 cm) rectangular or 7" (17.8 cm) round metal vent. Rigid metal vent is recommended. Plastic or metal foil vent is not recommended. • The length of vent system and number of elbows should be kept to a minimum to provide efficient performance.
PREPARE THE LOCATION 31/4" x 10" (8.3 cm x 25.4 cm) Vent System Vent Piece 31/4" x 10" (8.3 cm x 25.4 cm) 90 ° elbow 5.0 ft (1.5 m) 31/4" x 10" (8.3 cm x 25.4 cm) flat elbow 12.0 ft (3.7 m) 31/4" x 10" (8.3 cm x 25.4 cm) wall cap 0.0 ft (0.0 m) Example Before making cutouts, make sure there is proper clearance within the ceiling or wall. 1. Disconnect power. 2.Select a fiat surface for assembling the range hood. Place covering over that surface. 3.
To wire through top: 2.Mark a line distance (A) from the right of the centerline on the underside of the cabinet. Mark the point on this line that is 7/8" (2.2 cm) from back wall. Drill a 11/4" (3.2 cm) diameter hole (B) through the cabinet at this point. t I I I _ll I I I \ i B 7/8" (2.2 cm) from wall, not cabinet frame i Style 2 - Cut Openings for 31/4" x 10" (8.3 cm x 25.4 cm) Rectangular Vent System Roof Venting To make a 4"x 101/2" (10.16 cm x 26.
Style 3 - Cut Openings for 31/4" x 10" (8.3 x 25.4 cm) Rectangular Vent Transition to Round Vent Roof Venting To make a circular vent opening on the underside of the cabinet top: 1,Mark a centerline on the underside of the top of cabinet. 2,Mark a line 5" (12.7 cm) from the back wall on the underside of the top of cabinet. 3,Use a compass or a circle template to draw a circle with a diameter of 71/2" (19 cm). Use saber or keyhole saw to cut the circular vent opening.
2.Lift the range hood up under cabinet and determine final location by centering beneath cabinet. Mark on the underside of cabinet the location of the 4 keyhole mounting slots on the range hood (See slot dimensions on page 6). Set range hood aside on a covered surface. Vent Connector Installation Install 7" (17.8 cm) round vent mounting plate or 31/4" x 10" (8.3 x 25.4 cm) vent connector, depending on your vent system installation. Attach to range hood using the indicated screws provided in hardware kit.
1. Disconnect power. A.White wires B. Black wires C. UL listed wire connector il Do not reconnect power until the installation is complete. Before starting the installation, remove the grease filter, left and right side panels Complete installation to reinstall the side panels. 2.Remove the screw from the terminal box cover. Remove terminal box cover and set aside. A ................... i_.... B C _D ..................... E D.
lrNSTALL RANGE HOOD (Recirculating version) 1.Lift the range hood up under cabinet and determine final location by centering beneath cabinet. Mark on the underside of cabinet the location of the 4 keyhole mounting slots on the range hood (See slots dimensions on page 6). Set range hood aside on a covered surface. A 3.
RANGE HOOD USE Cleaning The range hood is designed to remove smoke and cooking vapors from the cooktop area. For best results, start the hood before cooking and allow it to operate several minutes after the cooking is complete to clear all smoke from the kitchen. A Charcoal Filter Kit to remove odors is available. See page 15 for more information regarding this kit. The hood controls are located on the front of the range hood.
3.To clean grease filter, soak the filters in hot water using a mild detergent. Rinse well and shake to dry. Or place in upper rack of dishwasher to clean. NOTE: Do not use ammonia. The aluminum on the grease filter will corrode and darken. NOTE: You can use either dishwasher or hot detergent solution and rinse in clean water. 2.Push up on the lens and turn it counterclockwise. 3.Remove the lamp and replace 1.Disconnect power. 50 watt it with a 120-volt, maximum halogen lamp with a GU10 base.
Problem Possible Causes Solutions After installation, the unit doesn't 1. The power line and the cable locking connector is not connecting properly, 1. Check the power connection with the unit is connected properly. work. 2. The wires from the switches are disconnected 2. Make sure the wires on the switches are or loose, connected properly. Light works, 1. The motor is defective, possible seized. 1. Change the motor. but motor is not turning, 2.
Warranty Your appliance is covered by a one year limited warranty. For one year from your original date of purchase, Electrolux will repair or replace any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed, used, and maintained in accordance with the provided instructions.
