GB Finding information Table of contents Please read and Save this QUITE ous 02 Keep a record for quick reference Important safety insertions eon! 02-04 Electrical requirements boor. Parts supplied To stalling the Boot... 06-10 Operation nnn. 1 Cleaning and Maintenance. ..naannmnnnmnnmnnmmn 11-12 TECHIE HA. sss senselessness 12 Troubleshooting corer 12 Environmental precis.
Important safety instructions 3 Important safety instructions AN WARRING a IMPORTANT To seduce the nosh of fire, curie shock or injury Io persons, observe the following: 5 FOR RESIDENTIAL USE ONLY. = Use the annelid only dn the manner intended by the manufacturer, I von have Indicates installation: operation, of maintenance malformation which is important Best not hazard intent, dustiness, contact he manufacturer.
important safety instructions Important safety instructions JIN warning Tu reluctance the risk of fire, use only piety duct work. Install this hood in accordance with all requirements specified. AN warning To reduce the risk of fire or electrical shack do net use this hood with any lexical solid state speed contra device. /\ WARNING To reduce the risk of 2 cooler lop grease fire: Never leave surface units Deadened at nigh settings, Rollovers cause smoking and greasy spillovers that may ignite.
+ Do not have a fuse in the neutral or ground circuit. md IMPORTANT Save nasalization constrictions for electrical Inspections Use. The range shortcrust be connected With topper wire only, The range hoot should be connected directly 10 le fused disconnect (or fountain breaker] box Hiccough metal electrical con dun. Wire sizes must conform to the requirements of the National Electrical Code EXPANSION 70 latest edition”, or CSA Standards Canadian Electrical Code Part 1 and C22.
8 installing the hood GB installing the hood IMPORTANT Gut installation. fay attention te precarious described in the assembly Mistletoe. We recommend that tvs people carry f+ i Preparation Determine the exact location of the range hood. Plan the route for venting exhaust to the outdoors (fig. Plan the power connection prior to installation so that electrical wiring will not be visible afterwards. House wiring location: The junction box is located on the top right side of the hood.
Flexible metal round ducts should only be used when no other duct fitting exists. Limit use to short lengths and do not crush when making comers.
GB installing the hood Long screws i — £13" Wood screws 10 Dimension Wall A {see table} Desired range hood distance above a 36” high cook top Ceiling height 8 Feet 9 Fest 10 Feet EET be wee | EE] 33" 34” 35" “with 10° extension chimney kit FWIOEXBOLS {16} {not supplied) Please call Frigidaire at 1.800.944.9044 to order this kit. 2 “Dimension A” In the chart represents the height from cook top to where the bottom screw mounting holes would be located.
installing the hood Electrical connections JI DANGER Dancer of selectness shock! All fittings must be installed by a competent person concordance with current wiring regulations and. local building regulations. Jf in doubt consult a annualized electrician. ma IMPORTANT Always switch off the electricity supply at the mains dung installation, cleaning she * maintenance.
GB installing the hood AN CAUTION Danger of injury, The chimney skirts may have some sharp edges, Exhaust operation s During exhaust operation, the range hood removes air from a room. if other fire sources that require the surrounding alr for combustion are being operated in the same room, gas, oil or coal heaters), the oxygen they require is taken away. Thus flames could be suffocated and gas could leak out or the fumes could be drawn back into the room.
Operation / Cleaning and maintenance Operation + Press one of the speed {s/s bunions to tum the appliance on. Button | Function a Press button © to switch the appliance off {pilot lamp is lit when appliance is switched on). v Press button e for low speed. »e Press button es for medium speed. ad Press button ss for high speed, 4 Press button # to turn on fights. Press ’ again to switch lights off.
Troubleshooting GB fg. Technical data Power supply 120V~, 60Hz Power consumption 520wW Bulb type 2% 20W, 120V~ type: GU) Power cable type 18AWG {Amer. Wire Gauge) 300V~, 105°C Troubleshooting Problem Cause Solution The appliance | Take down is not fixed the appliance properly on the | and check iris brackets. properly fixed. Erosive The fan blade : is damaged. The fan motor | Switch off the is not fixed appliance. tightly.
Warranty information Your appliance is covered by a one year limited warranty, For one year from your original date of purchase, Electrolyte will pay all costs for repairing or replacing any parts of this appliance that prove to be defective in materials or workmanship when such appliance Is installed, used and maintained in accordance with the provided instructions. Exclusions This warranty does not cover the following: 1.