Important Safety Instructions This product requires a three-prong grounded outlet. The installer must perform a ground continuity. check on the power outlet before beginning the installation to insure that the outlet box is properly grounded. If not properly grounded, or if the outlet box does not meet electric requirements noted (under ELECTRICAL REQUIREMENTS), a qualified electrician should be employed to correct any deficiencies.
OVERVIEW OF INSTALLATION PROCEDURE ‘This section gives a brief overview of what you need to do to install this microwave: Read entire instructions before you begin installation. ‘Before you install this microwave, remove the adhesive tape, if there is any; on the exhaust adapter, grease filters and-power supply cord, 1. Install an outlet and make sure you meet the electrical requirements for this installation. 2. Open the installation hardware packet.
[3] HOOD EXHAUST DUCT Quayside ventilation require HOOD EXHAUST DUCT. Read the follow ily. EXHAUST CONNECTION: The hood exhaust has been designed to mate with a standard 3% x 10" rectangular duct, If a round duct is required; a rectangular-to-round transition adapter must be used. Do hot use less than a6” diameter duct.
| [4] REMOVE THE MOUNTING PLATE The mounting plate comes attached to the hack of the microwave oven. 1. Stand the microwave on its control panel side. Use a portion of the carton or some other material to protect the outer case from being damaged. Mounting Plate Control Panel Side / Control Panel Side. 2. Remove the 3 ‘Screws from the mounting plate as shown. Cen P : 3. This plate-will be used as the rear wall template. st 4. Locate exhaust adapter, grease filters and hardware packet. = 5.
| [5] MICROWAVE EXHAUST DUCT (continued) B: OUTSIDE BACK EXHAUST ~ (Horizontal Duet) | This microwave oven is shipped assembled for top exhaust, However, you will need to make adjustments to assure proper alignment with your current exhaust duct after the microwave is installed.” install or remove the exhaust adapter from blower plate you need to first remove. the damper... . + ‘Pull the damper up: * Squeeze the diagonal.corners to allow the damper fo be removed.
* The wires should be routed in the grooves of the motor frame: 5.» Guide the wires into the dug as you place "the blower unit back into the opening, "» Secure the blower unit to the microwave with the screw from Step 3. CAUTION: Da not pull or stretch fhe blower unit wiring! Make sure the wires ate not pinched.’ 6. Replace the Howe plate in the same position : as before with the screw. 7. Replace the data per back: into the exhaust adapter. -8, Fit the exhaust adapter into the house duct.
[5] MICROWAVE EXHAUST DUCT (continuity) 2, Reinforce 3. Lift off the: SO blower plate, Remove and save the screw that . x out the blower unit. The wires will extend far enough to allow you to adjust the blower unit. i" * Roll the blower unit so that the fan blades are facing towards the front. of the microwave, BEFORE: Fan Blades are Facing Up = AFTER: Fan Blade Openings “Facing Front of Microwave » The wires should be routed in the grooves of the motor frame. 5.
[6] PREPARATION OF TOP CABINET Unbounded to drill holes for the top support screws and alcohol large enough for the power cord to fit through. ©: * Read the instructions on the top cabinet template, * Tape it underneath the top cabinet. * Drill the holes, following the instructions on the template. “ [Z] ATTACH THE MOUNTING PLATE STONEWALL Your microwave oven needs to be mounted against and supported by a flat, vertical walk.
[7] ATTACH THE MOUNTING PLATE TO THE WALL (contrived) * [A an fhe plate 'to the tall To use toggle _ bolts: fro the bolts. “replace the re wings “éndé. Inert the toggle wings he hottest the wall to mount Ge bracket You may pull “forward on the bracket to'help in tightening the toggle bolts. Tighten all bolts. wofemle—t Space Mare Than Wall Thickness 1. Touched Wings Az Toggle Bol ih End prepare the rear wall cutout opening for outside back exhaust: 1.
4. Install the grease filters and remove the tape from the cook top lamp cover on the bottom of € oven. 5. For top exhaust open the top cabinet and attach the exhaust adapter to the microwave through the cabinet bottom. For front-to-back or side-to-side adjustment, slide the exhaust adapter as needed. Blower Late Damper Back of \ Microwave J ° Adapter Luau previously removed the exhaust adapter: ith the damper out, twist the exhaust adapter to fit under the flaps of the blower plate.