Installation Instructions

ManualsBrandsFrigidaire ManualsCooking30" White Microwave Trim Kit

Table Of Contents

Installation

Instructions

Built-in Trim Kit

Models # FMTK3027AS FMTK3027AD FMTK3027AB

FMTK3027AW FMTK2727AS FMTK2727AB

BEFORE YOU BEGIN

• IMPORTANT – Save these instructions

for local inspector's use.

• IMPORTANT – Observe all governing

codes and coordinates.

• Note to Installer – Be sure to leave

these instructions with the Consumer.

• Note to Consumer – Keep these

instructions for future reference.

• Skill level - Installation of this appliance

requires basic mechanical and electrical

skills

Read these instructions completely and carefully.

• Proper installation is the responsibility of the

installer.

• Product failure due to improper installation is

not covered under the Warranty.

• Unplug the microwave oven before

attempting installation of this kit.

• Because the kit includes metal parts, caution

should be used in handling and installation to

avoid the possibility of injury.

• Do not remove permanently affixed labels,

warnings, or plates from the product. This

may void the warranty.

FOR YOUR SAFETY:

WARNING – Before beginning the installation,

switch power off at service panel and lock the

service disconnecting means to prevent power from

being switched on accidentally. When the service

disconnecting means cannot be locked, securely

fasten a prominent warning device, such as a tag, to

the service panel.

IMPORTANT - PLEASE READ

AND FOLLOW

THIS BUILT-IN KIT IS DESIGNED FOR USE

ONLY WITH MICROWAVE

OVENS SPECIFYING BUILT-IN KIT

FMTK3027AS/D/B/W OR

FMTK2727AS/B/W ON THE RATING LABEL ON THE

LEFT SIDE WALL OF THE MICROWAVE OVEN

CAVITY.

QUESTIONS?

For customers in the United States call:1-1800-944-9044

For customers in Canada call: 1-800-265-8352 (English)

1-800-668-4606 ext.8199 (French)

Visit our Website at: www.frigidaire.com

READ CAREFULLY.

KEEP THESE INSTRUCTIONS.

PN: A06823523

EN-1

July 2021

FMTK2727AW

FRIGIDAIRE

IMPORTANT:

Before installing the exhaust duct, confirm the floor is level.

The level bubble should be equal distance from level guide

lines.

16170000A84905

Summary of content (16 pages)

PAGE 1
Installation Instructions BEFORE YOU BEGIN • • • • Models # FMTK3027AS FMTK3027AD FMTK3027AB FMTK3027AW FMTK2727AS FMTK2727AB FMTK2727AW Read these instructions completely and carefully. IMPORTANT – Save these instructions • for local inspector's use. • IMPORTANT – Observe all governing codes and coordinates. • Built-in Trim Kit Note to Installer – Be sure to leave • these instructions with the Consumer. • Note to Consumer – Keep these instructions for future reference.
PAGE 2
Installation Instructions PARTS INCLUDED IN THE KIT 1. Front Frame Assembly- QTY 1 2. Exhaust Duct - QTY 1 Bottom Mounting Rail – QTY 2 3. Screw A - QTY 11 (3.9X8.0 mm) 4. Screw B - QTY 4 (4.0X20 mm) CHOOSING A LOCATION FOR YOUR MICROWAVE OVEN IF BUILT-IN Built-In Trim Kit allows for the installation of microwaves listed below to be built into a cabinet or wall by itself or over an electric wall oven*.
PAGE 3
Installation Instructions Screw A Center Line Illustration 3 ELECTRICAL OUTLET LOCATION Outlet should NOT be in the shaded area as indicated on Illustration 3 NOTE 1: The floor of the opening should be constructed of plywood strong enough to support the weight of the oven and floor load (approximately 100 pounds). The floor should be level for proper operation of the oven. Be sure to check the local building code as it may require that the opening be enclosed with side, ceiling and rear partition.
PAGE 4
Installation Instructions Bottom Mounting Rail 1. Turn microwave upside down so you are looking at oven bottom. Secure the bottom Mounting Rail on oven with four screws A. See Illustration 5 below. Screw A OVEN INSTALLATION 1. Place the oven adjacent to the wall or cabinet opening. Plug the power cord into the electrical outlet. IMPORTANT: Protect cabinet when placing on counter top. 2. Carefully guide the assembled oven into the prepared opening. Slide the oven on the Exhaust Duct Assembly.
PAGE 5
Installation Instructions FRAME INSTALLATION 1. 2. Position the FRAME ASSEMBLY to be square with the oven. Carefully place the FRAME ASSEMBLY on the oven. See Illustration 7. Check that it is level and then secure with two Screws B. Secure the bottom portion of the FRAME ASSEMBLY with the two remaining Screws B. See Illustration 8.
PAGE 6
Instrucciones para la instalación ANTES DE COMENZAR      IMPORTANTE – Guarde estas instrucciones para su uso por el inspector local. IMPORTANTE - Observe todos los códigos y reglamentos en vigor. Nota para el instalador - Cerciórese de dejar estas instrucciones con el consumidor. Nota para el consumidor – Guarde estas instrucciones para futura referencia. Nivel de habilidad – La instalación de este artefacto requiere habilidades mecánicas y eléctricas básicas.
PAGE 7
Instrucciones para la instalación PARTES QUE SE INCLUYEN EN EL KIT 1. Conjunto de marco frontal – CANT. 1 2. Conjunto de conducto extractor – CANT. 1 3. Tornillo A – CANT. 11 (3.9X8.0 mm) Tornillo A 4. Tornillo B – CANT. 4 (4.
PAGE 8
Instrucciones para la instalación Tornillo A centro de la línea Ilustración 3 UBICACIÓN DEL TOMACORRIENTE El tomacorriente NO debe encontrarse en el área sombreada que se indica en la Ilustración 3. Ilustración 4 CONJUNTO DE CONDUCTO EXTRACTOR 1. Dibuje una línea central en el piso NOTA 1: El piso de la abertura deberá estar construido de madera laminada que sea lo suficientemente fuerte como para soportar el peso del horno y la carga sobre el piso (aproximadamente 100 libras).
PAGE 9
Instrucciones para la instalación INSTALACIÓN DEL MARCO 1. Hace ala onda demicroondas arrivay abajo por lo que 1. está buscando en la parteinferior del horno. Asegure la parte inferior de montajeen carril del horno con cuatro tornillos A. Véase la ilustración 5. Tornillo A Coloque el horno en posición adyacente a la abertura de la pared o del gabinete. Enchufe el cordón eléctrico en el tomacorriente. IMPORTANTE: Proteja el gabinete cuando lo coloque sobre la encimera. 2.
PAGE 10
Instrucciones para la instalación 1. Coloque la CONJUNTO DEL MARCO para ser cuadrado con el horno. Coloque cuidadosamente la CONJUNTO DEL MARCO en el horno. Véase la ilustraci ón 7. 2. Compruebe que es plataforma y luego asegure con dos tornillos B. Asegure la parte inferior del conjunto del bastidor con los dos tornillos restantes B. Véase la ilustraci ón 8.
PAGE 11
Instructions d'installation Ensemble de garniture Instructions d'encastrement d'installation FMTK3027AS FMTK3027AD FMTK3027AB FMTK3027AW FMTK2727AS FMTK2727AB FMTK2727AW AVANT DE COMMENCER  IMPORTANT – Conserver ces instructions à l’usage de l’inspecteur local.  IMPORTANT – Respecter tous les codes et règlements régissant une telle installation.  Note destinée à l’installateur – S’assurer de laisser ces instructions au consommateur..
PAGE 12
Instructions d'installation PIÈCES INCLUSES 1. Cadre avant – QTÉ 1 2. Conduit d’évacuation – QTÉ 1 3. Vis A – QTÉ 11(3.9X8.0 mm) 4. Vis B – QTÉ 4 (4.0X20 mm) CHOIX DE L'EMPLACEMENT DE VOTRE FOUR À MICRO-ONDES ENCASTRÉ Vis A L’ensemble de garniture d’encastrement est compatible avec les fours à micro-ondes indiqués ci-dessous. Le four peut être encastré dans une armoire, dans un mur ou audessus d’un four mural électrique.
PAGE 13
Instructions d'installation Vis A Vis A Vis A la ligne médiane Illustration 4 Illustration 3 EMPLACEMENT DE LA PRISE DE COURANT La prise de courant ne doit PAS être placée dans la zone ombrée, comme le montre l’illustration 3. MONTAGE DU CONDUIT D'ÉVACUATION 1. Dessiner une ligne centrale sur le plancher Placer le conduit d’évacuation dans l’ouverture. Lorsque le conduit d’évacuation est positionné correctement dans l’ouverture, les brides reposent fermement contre le bord inférieur de l’ouverture.
PAGE 14
Instructions d'installation Bas De Montage Ferroviaire 1.Tourner le four ¨¤ micro-ondes ¨¤ l'envers alors tu vois le INSTALLATION FOUR 1. Placer le four à côté de l’ouverture pratiquée dans l’armoire ou le mur. Brancher le cordon d’alimentation dans la prise de courant. fond du four. Fixer le fond de Rail de Montage sur le four avec quatre vis A. Voir l`illustration 5 ci-dessous. Vis A IMPORTANT : Protégez l'armoire lorsqu'elle est placée sur un plan de travail. 2.
PAGE 15
Instructions d'installation INSTALLATION DU CADRE 1. Positionner le CADRE de manière à ce qu’il soit d’équerre avec le four. Voir l’illustration 7. 2. Vérifiez qu'il est plat, puis fixer avec deux vis B. Fixer la partie inférieure de le CADRE avec les deux vis B qui restent. Voir l`illustration 8.
PAGE 16