Installation Instructions Overthe Range Microwave Oven BEFORE YOU BEGIN Read these instructions completely • IMPORTANT instructions - Savethese ti)r local inspe{tor's • IMPORTANT and carefully. use. - Obse,,-e all governing • codes and ordinances. Note to Installer - Be sure instructions xdth the ( onsumer. to leave these • Note to Consumer instructions fi)r flmue - Keep these reference. • SkilllevelInstallationofthisappliancerequires basic mechanical and electrical skills.
Installation Instructions Recirculating CONTENTS Attach Mounting General information Important Safety Instructions Electrical Requirements Hood Exhaust .................................. 4-5 ............................ 6 .......................................................... 6 Tools You Will Need ................................................ 7 Mounting 7 ......................................................
Installation Instructions mMPORTANT SAFETY mNSTRUCTmONS You should have the wall receptacle and circuit checked by a qualified electrician to make sure the receptacle is properly grounded. This produ( t requires a three-pro_g grounded omlet. The inaalier must perform a groined (::omimfi bcheck on the power omlet box before beghming the iustallafion to insme d_at d_e omlet box is properly grom_ded.
Installation Instructions HOOD EXHAUST NOTE: Read these next two pages only if you plan to vent your exhaust to the outside. If you plan to recirculate the air back into the room, proceed to page 6. OUTSIDE TOP EXHAUST Tile fi)llo_fing chart des(rihes du(twork installation. (EXAMPLE an example ONLY) of one possihle EQUWALENT LENGTH x NUMBER USED EQUIVALENT LENGTH 24Ft. (7.32m) x (1) 24 Ft. (7.32m) 12 Ft.Straight Duct RoofCap (6" Round) 12 Ft. (3.66m) x (1) 12 Ft. (3.
Installation Instructions Maximum NOTE: If you need to install ducts, note that the total duct length of 3 V/' x 10" rectangular or 6" diameter round duct should not exceed 140 equivalent feet (42.67 m). Outside ventilation requires a HOOD DU(T. Read the follo_dng carefiflly. EXHAUST Elbows, transitions, wall and roof caps, etc., present additional resistance to airflow and are NOTE: It is important that venting be installed using the most direct route and with as tew elbows as possible.
Installation Instructions PARTS INCLUDED DAMAGE - SHmPMENT/ HARDWARE * If the unit is damaged in shipment, re_uvn d_e unh _o d_e s_ore h_ whhh h was bough_ for repair or PART QOANTITY * If the unit is damaged by the customer, rep_ir 05 veplacemem is d_e responsibility of d_e _us_omer. ff the unh is damaged be made is_ss_allev.
Installation Instructions TOOLS YOU WILL NEED Ruleror tape measureand Pencil #1 and#2 Phillipsscrewdriver t edge (optional) Tin snips(for cutting damper,if required) Scissors Electricdrill with ¾_"VS"and%" drill bits (to cut template, if necessary) Gloves Saw(saber,holeor keyhole) Stud finder Hammer (optional) Level Safety goggles MOUNTING er Fillerblocksor scrap wood pieces,if needed for top cabinetspacing (usedon recessedbottom cabinet installationsonly) Duct and masking tape SPACE NO
Installation I- PLACEMENT I'_ Instructions OF THE MOUNTING REMOVING THE MICROWAVE OVEN FROM THE CARTON/ REMOVING THE MOUNTING PLATE [] Remove tile installation instructions, filters, glass tray and the small hardware bag. Do not remove the Styroloam protecting the front of tile oven. [] Fold back all 4 carton flaps flflly against carton sides. Then careflflly roll the oven and carton over onto the top side. The oven should be resting in the SUrolbam.
Installation DETERMINING Plate position cabinet Instructions WALL PLATE LOCATION - beneath UNDER YOUR CABINET Plate position - beneath cabinet bottom flat bottom framed MountingPlateTabs i the Cabinet Bottom recessed Mounting Plate Tabs Touching the Back Frame -:: c I)iLUIIIFL II I II tl 30" (76.2 cm) to Cooktop At least 30" (76.2 cm), u to 6 (g!.
Installation ALIGNING Instructions THE WALL PLATE ) ( t I Hole Draw a Vertca i LineonWall u_-- fromCenterof i T°pCabinet ._ %," 1 HoleD ', HoleC J; CAUTION: Wear gloves to avoid cutting fingers on sharp edges. [] Draw a vertical line on the wall at tile center of tim 30" (76.2 cm) wide space. [] Use tile mounting plate as the template tot the rear wall. Place tile mounting plate on the wall, making sure that the tabs are touching the bottom of the cabinet.
Installation INSTALLATION This microwave tollowing three oven types is designed lot adaptation of ventilation: A. Outside Top Exhaust B. Outside Back Exhaust C. Recirculating TYPES (Vertical (Choose A, B or C) NOTE: This microwave is shipped assembled tot Outside Top Exhaust (except fin non-vented models). Select tile type of ventilation required tot your installation and proceed to that section.
Installation Instructions OUTSIDE TOP EXHAUST INSTALLATION (Vertical Duct) OVERVIEW A 1. Attach Mounting Plate to Wall A2. Prepare Top Cabinet A3. Check Damper Operation A4. Mount Microwave Oven A5. Adjust Exhaust Adaptor A6. Connect Duc/work I-_ To use toggle ATTACH THE MOUNTING PLATE TO THE WALL bolts: Spacing forToggles MoreThanWall +l..-.[.--Th ckness Mounting Plate _= Bolt End [] \ Attach the plate to tile wall using toggle bolts.
Installation Instructions USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET MOUNT OVEN THE MICROWAVE You need to drill holes for the top support screws, a hole large enougll for tile power cord to fit through, and a cutout large enougll for tile exhaust adaptor. FOR EASIER INSTAIJATION AND PERSONAI, SAFETY, WE RE( OMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN. IMPORTANT: Do not during installation.
Installation Instructions CabinetFront ADJUST THE EXHAUST ADAPTOR CabinetBottomShelf Filler Block Open the top cabinet and a([iust tile exhaust adaptor to connect to the house duct. T [] Depth ofquivalentto Cabinet Recess Blower Plate For Front-to-Backor Side-to-Side Adjustment,Slidethe ExhaustAdaptoras Needed Insert 2 self:aligning screws through outer top (abinet holes. Turn two flfll turns on each screw. _'_ CONNECTING n Tighten center screw completely.
Installation Instructions OUTSIDE BACK EXHAUST INSTALLATION B1. B2. B3. B4. B5. Prepare Attach Prepare A(ljust Mount (Horizontal Duct) OVERVIEW Rear Wall Mounting Plate to Wall Top Cabinet Blower the Microwave Oven This microwave oven is shipped assembled ti)r top exhaust. You will need the exhaust adaptor fin. installation in the rear wall opening.
Installation _-_ Instructions To use toggle PREPARING THE REAR WALL FOR OUTSIDE BACK EXHAUST Spacing for Toggles More -_l_-_i_ ThanWallThickness Toggle Wings (continued) House Duct bolts: i Mounting Plate Damper Hinge On Top B01tEnd DamperSwings [] [_Fit tile exhaust adaptor into the house duct as shown. Make sure the exhaust adaptor (with the damper) is squared up in the house duct and lines up with the holes in the mounting plate. []Remove the paper f_om the sticky side of the 28" (71.
Installation I-_ Instructions [] ADAPTING MICROWAVE BLOWER FOR OUTSIDE BACK EXHAUST Roll the blower unit 90 ° so that fan blade openings are lacing out the back of the uliciowave, BeforeRolling Remove t0 UlI( and save screw that holds bh)wer After Rolling motor I'OW}lVe, Blower Motor _ Micr0wave __ Backof -_ - "_ [] Backof Microwave BI0werM0t0r Screw [] Careflflly pull out the bh)wer unit. The _dres _dll extend far enough to alh)w you tr) adjust the 1)lower unit.
Installation Instructions CabinetFront MOUNT OVEN THE MICROWAVE CabinetBottomShelf FillerBlock T to Depth ofquivalent Cabinet Recess Self-AligningScrew FOR L4SIER INSTAI,IATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN. IMPORTANT: Do not during installation. grip or use handle [] NOTE: If your cabinet is metal, use tile nylon grommet around tile power cord hole to prevent cutting of tile cord. Insert 2 sell:aligning screws through outer top cabinet holes.
Installation RECIRCULATJNG INSTALLATION C1. Attach Mounting OVERVIEW Instructions (Non-Vented #uctJess) | Plate to Wall C2. Prepare Top Cabinet C3. Check Microwave Assembly CA. A(ljust Blower C5. Mount the Microwave Oven _ .... / C6. Install Charcoal Fiher I-_ [] ATTACH THE MOUNTING PLATE TO THE WALL Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to mount the plate.
Installation Instructions CHECK MICROWAVE ASSEMBLY [] Carefhlly pull out tile bh)wer unit. Tile wires xdll extend far enough to alh)w you to adjust tile bh)wer unit. [] Roll tile bh)wer unit 90 ° so that fan blade openings are facing toward the flrmt of the mi(rowave. Exhaust Adaptor (absent on models shipped for recirculatirm exhaust Backof Microwave ; • Place tile microwave in its upright top of tile unit lacing up. position, with tile • The microwave oven may be shipped assembled fin.
Installation Instructions NOTE: When inounting ADAPTING MICROWAVE BLOWER FOR RECJRCULATJON (continued} [] IJft inicrowave, tilt it forward, and hook slots at back bottoin edge onto fimr lower tabs of inounting plate. _ Rotate flont of oven up against cabinet bottoln. [] Insert a sell:aligning screw through top center cabinet hole. Teinporarily secure tile oven by turning the screw at least two full turns after the threads have engaged. (It will be completely tightened later.
Installation MOUNT OVEN [] Instructions iNSTALLING THE CHARCOAL FILTER THE MICROWAVE (continued} Insert 2 self:aligning screws through outer top (abinet holes. Turn two flfll turns rm each screw. [] Remove 2 screws on flrmt r)f grille using a #1 Phillips s( rewdriver, [] Open the door. [] Remove the grille. Charcoal [] [] [] Tighten center screw completely. Tighten the outer two screws to the top of the microwave oven.
Installation Instructions BEFORE YOU USE YOUR MICROWAVE _k4ke _he micro_%_ve o_er_ h;-_s been installedsllFe according _o instructions. _l_e Owner's Marmal. [_ Read [_ KEEPTHE INSTALLATK)N INSTRUCTIONS FOR L()CAI_ INSPECT()R'S USE. / / _3 Remove all packing mi( ro_,k2_ e o_erh I ['_ Install turntable [_ Replace material flom _he I and ring in cavity. house fi_se or turn breaker back on. IilIIII1/11 -_ lug power (:ord imo ele(:_ri(:al omle_.
164D3370P 1,57 49- 40165 12-00 JR Printedin Korea
