Installation Instructions Over the Range Microwave Oven Questions? Call or BEFORE YOU BEGIN Read these instructions completely and carefully. IMPORTANT sue these instructions for local inspector's use. IMPORTANT overran governing codes and ordinances. + Note to Installer — Be sure to leave these instructions with the Consumer. Note to Consumer — Keep these instructions for future reference. Skill level Installation of this appliance requires basic © cal and electrical skills.
Installation Instructions CONTENTS General information Important Safety Instruction: Electrical Requirements Damage — Shipment/ Installation. Parts Included... Teals You Will Need Mounting Space Step-by-step installation guide Phi cement of The Mounting Plate Removing the Mounting Plate Finding the Wall Studs Plate Location... Determining Wall Aligning the Wall Plate Hood Exhaust [A] Outside Top Exhaust Attach Mounting Plate to Wa Preparation of Top Cabinet.
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS This product requires a three-prong grounded outlet. The installer must perform a ground continuity check on the parer outlet hox before beginning the installation to ensure that the outlet box is properly grounded.
Installation Instructions DAMAGE—SHIPMENT/ INSTALLATION * If the unit is damaged in shipment, return the unit to the store In which it was bought for repair or replacement * If the unit is damaged by the customer, repair or replacement is the responsibility of the customer ¢ If the unit is damaged by the installer (if other than the customer), repair or replacement must be made by arrangement between customer and installer.
Installation Instructions TOOLS YOU WILL NEED Phillips screwdriver Tiny saps (for cutting > arm per, if required) Ruler or tape measure and straight edge Pen cit Carpenter square {optional} Scissors {to cut template, if necessary) Electric drill with drill pits Filler blocks ur scrap would pieces, if fest Tor top cabinet spacing ST fused on recessed bottom Ta i cabinet installations aly) w (saber, hole or keyhole) Stud finder or Hammer {optional} & Safety fogies Duct and masking tape MOUNTING SPACE space be
Installation Instructions PLACEMENT OF THE MOUNTING PLATE REMOVING THE MICROWAVE OVEN FROM THE CARTON/ REMOVING THE MOUNTING PLATE 1: Remove the installation instructions.use and care, exhaust adapter. turntable ring, shelf tray and the small hardware bag. Da t the Styrofoam protecting the front of the oven. Small Hardware Bag Exhaust Adapter Turntable Ring below glass tra; Glass Tray 2 Fold back all 4 carton flaps fully against carton sides. Then carefully roll the oven and carton over onto the top side.
Installation Instructions C. DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET Plate position-beneath flat bottom cabinet Draw a vertical line on | the wall at the center of the 307 wide space Tape the Rear Wall Template onto the wall matching the center line and touching the bottom of the cabinet. Al least 307 Plate position-beneath framed recessed cabinet bottom 30” 1 Cookie Draw a vertical line on the wall at the center of the 30” space.
Installation Instructions D.| ALIGNING THE WALL PLATE Horizontal Line anal CAUTION: Wear gloves to avoid cutting fingers on sharp edges. SEAR CONTEMPLATE Centurion notches Draw a Vertices] Line an Wall from: Enter af Top Cabinet Hole & Horizontal Line Draw a horizontal fine on wall at the [1] Draw a vertical line on the wall at the center of the 30" wide space. 2 Draw a horizontal line on the wall at the bottom of “Rear Wall Template”. 3 Find a wall stud in area "E" of mounting plate Refer to section 1B.
Installation Instructions 2 INSTALLATION TYPES (Choose This microwave oven is designed for adaptation to NOTE: This microwave is shipped assembled for the following three types of ventilation: Reciprocating. Select the type of ventilation required A. Outside Top Exhaust (Vertical Duct) for your installation and proceed to that section. B. Outside Back Exhaust (Horizontal Duct) €.
Installation Instructions INSTALLATION INSTRUCTIONS FOR EXTERNAL EXHAUST DUCTING NOTE: It you need to install ducts, note that the total duct length of 3%" x 107 (8.2 x 25.4 cm) rectangular or 5" (12.7 cm) diameter” 6° (15.2 cm) diameter round duct should not exceed 120 equivalent feet (36.5 m). Suicide ventilation requires an EXTERNAL EXHAUST DUCT Read the following carefully. NOTE: Ii is important that venting be installed using the most direct route and with as few elbows as possible.
EXTERNAL EXHAUST DUCTING Installation Instructions OUTSIDE TOP EXHAUST (EXAMPLE ONLY) The following chart describes an example of one possible duct work Installation. Transition Adapter” EQUIVALENT NUMBER EQUIVALENT DUCT PIECES LENGTH X USED = LENGTH = Roof Cap 4f 73m x {1 = 24F (13m 12 Ft. {3.6 mj Straight Duct 12k (36m) cm Round) y, Rectangular-to-Rend FOSSA {15m Cis Equivalent lengths of duct pie are based on actual tests and reflect requirements for good venting performance with any vent hood.
Installation Instructions A | OUTSIDE TOP EXHAUST (vertical Duct) INSTALLATION OVERVIEW Al. Attach Mounting Plate to Wall AZ. Prepare Top Cabinet A3. Adapting Microwave Blower for Outside Top Exhaust Ad. Check Damper Operation AS. Mount Microwave Oven AB. Adjust Exhaust Adapter A7. Connect Duct work IMPORTANT NOTES: * Make sure the screws for the blower motor and blower plate are securely tightened when they are reinstalled. This will help to prevent excessive vibration.
Installation Instructions A2. FOR PREPARATION OF TOP CABINET You need to drill holes for the top Support screws, a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adapter. * Read the construction on the TOP CABINET TEMPLATE. * Tape it underneath the top cabinet. * Drill the hol TOP CABIN following the instructions on the ‘PLATE. CAUTION: Wear safety goggles when rifling holes inn the cabinet bottom, USE TOP CABINET TEMPLATE A3.
Installation Instructions A3 ADAPTING MICROWAVE BLOWER FOR OUTSIDE TOP EXHAUST 5 Secure blower unit to microwave with the screw removed in Step 1. Make sure the screw is ght. [8] Replace blower plate with the screw removed in Step 1. Make sure the screw is tight. ¥ Back of -microwave 4 Attach the exhaust adapter to the top of the * blower plate by sliding it into the guides of the blower plate. Adapter Buck of e-Ricrowave Locking Tab Push in secy. until it is in the locking tabs.
Installation Instructions A5.| MOUNT THE MICROWAVE OVEN (cont.) Cabinet Front J Cabinet Bottom Shelf /Tier Block Equivalent | Rec CC SHEET fe Leif Aligning Ss Microwave Oven Top 4 Attach the microwave oven to the top cabinet, [5] Insert 2 self aligning screws through outer top cabinet holes. Turn two full turns on each screw, ¥ f Tighten center [7 Tighten the outer two screws to the top of the microwave oven. (While tightening screws, hold the microwave oven in place against the wall and the top cabinet.
Installation Instructions B OUTSIDE BACK EXHAUST (Horizontal Duct) INSTALLATION OVERVIEW i B1. Prepare Rear Wall B2. Remove Blower Plate B3. Attach Mounting Plate to Wall Bd. Prepare Top Cabinet B5. Adjust Blows B6.
Installation Instructions B3.| ATTACH THE MOUNTING PLATE TO THE WALL Attach the plate to the wall using toggle bolts At least one wood screw must be used to attach the plate ta a wall stud [1] Remove the toggle wings from the bolts. 2 Insert the bolts into the mounting plate through the holes designated to go into drywall and reattach the toggle wings note each blat.
Installation Instructions ADAPTING MICROWAVE BLOWER FOR OUTSIDE BACK EXHAUST (cont.) B5. 3 Roll the blower unit 90° Before Rotation After Rotation Back of Microwave Microwave 4 Rotate blower unit counterclockwise 180°. Before Rotation After Rotation 5 iw Back of Microwave 2 remove the wires farm the grooves.
Installation Instructions MOUNT THE MICROWAVE OVEN FOR EASIER INSTALLATION AND PERSONAL SAFETY. WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN. IMPORTANT: Do net grip or use the handle or heat shield during installation, Do not remove the cardboard spacers between the heat shield and door. NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord. NOTE: We recommend using filler blocks if the cabinet front hangs below the cabinet bottom shelf.
Installation Instructions C | RECIRCULATING (Non-Vented Ductless) INSTALLATION OVERVIEW C1. Attach Mounting Plate ta Wall C2. Prepare Top Cabinet C3. Check Blower Plate C4. Mount the Microwave Oven C5. Install or change Charcoal Filter IMPORTANT NOTES: * Make sure the screws for the blower motor and blower plate are securely tightened when they are reinstalled. § This will help to prevent excessive vibration * Make sure the motor wiring I and secured, and that the wir s been properly routed.
Installation Instructions C2.| USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws and a hole large enough for the power cord to fit through. * Read the instructions on the TOP CABINET TEMPLATE. * Tape it underneath the top cabinet. NOTE: Adjust top template accordingly if the microwave is being spaced aut from the wall due to cabinet depth {including cabinet doors) of more than 13" * Drill the holes. following the TOP CABINET TEMPLATE.
Installation Instructions C4.| MOUNT THE MICROWAVE 2] Open the microwave door and remove the two OVEN (cont.) vent mounting screws located on top of the microwave using a #1 Phillips screwdriver. J 15 Insert 2 sell-aligning screws through outer top cabinet holes. Turn two full turns on each screw. 3 Tip forward. Lift out to remove. 4 Install the charcoal filter. Lay the filter on the back 6 Tighten center of the grille with the black mesh face upper.
Installation Instructions BEFORE YOU USE YOUR MICROWAVE 1. Make sure the microwave oven has been installed according to instructions. Turnover all packing material from the microwave vane Install turntable ring and glass tray in cavity Plug power cord into a separate and dedicated 15th 20-amp electrical outlet. 5. Replace house fuse or turn breaker back on.
Tr TH Co ISI 0G U5 A080 Ld 30" ACTINIUM WIDTH REQUIRED ~ REAR WALL TEMPLATE [of vou vouch PI: EN-24 Printed in China
Instrucciones de instalación Horno microondas (encima de la estufa) preguntas? Llame ol o ANTES DE EMPEZAR Leas estas instrucciones completamente y con atención. ‘IMPORTANTE: coacerve este: instrucciones para uso futuro del inspector focal. IMPORTANTE: corcovease ce que se cumplan todas las norma y los códigos relevantes. “Nota para el instalador: regirnos de dejar estas instrucciones en manos del consumidor. Nota para el consumidor: conserve estas instrucciones para referencia futuro.
Instrucciones de instalación 1 | COLOCACIÓN DE LA PLACA DE INSTALACIÓN > PROCEDIMIENTO PARA SACAR DE LA CAJA EL MICROONDAS Y LA PLACA DE INSTALACIÓN 1 Rore los construcciones de institucional, usa y laido, adaptador de escape, anillo giratorio, estate, filtros, bandeja de vidrio y bolsa de sucesorios pequeñita. No retire ef poliestireno de la parte delantera del horno.
Instrucciones de instalación C. UBICACIÓN DE LA PLACA PARA LA PARED DE BAJO DEL GABINETE Posición de la placa-debajo de la superficie plana inferior del Dibujante una linea verifico en la puread en el centro del espacio cuyo cho es 307.
Instrucciones de instalación D.| ALINEACIÓN DE LA PLACA PARA LA PARED asc de la Agüero 8 La lunes horizontal film E PRECAUCIÓN: para evitar catres por los horades afilados. 1 [Trace una linea vertical en la pared, en el centro del espacio cuyo ancho es 30". 2 Trace una linea horizontal en la pared desde el fondo de "Plantilla de pared posterior.” Encuentre un travesaño en el rea E de la placa de wl montaje. Consulte la sección 1B: Encontrar travesados de pared.
Instrucciones de instalación INSTRUCCIONES DE INSTALACIÓN DE CONDUCTOS DE ESCAPE EXTERNAS NOTA: en caso dle que seq necesario instilar conductos, tenga en cuenta que ef largo total de los conductos. rectangulares {anche de 3 174" X 107 48,2 cm X 25,4 em) 0 redondos {diezmero de 576 12,7 an} /(diámetro de 67 15,2 cm) NQ debe ser superior a 120 pies (36,5 m). La ventiscan exterior requiere el uso de un CONDUCTO PARA CAMPANA EXTRACTORA. Lea con atención las siguientes recomendaciones.
Instrucciones de instalación CONDUCTOS DE ESCAPE EXTERNAS EXTRACCIÓN SUPERIOR EXTERNA (SOLO EJEMPLO) La siguiente tabla contiene un ejemplo de una pasible instalad de un sistema de conducta de estroncio LARGO (MEDIDAS No DE UNIDADES LARGO (MEDIDAS PIEZAS DEL CONDUCTO EQUIVALENTES) x UTILIZADAS EQUIVALENTES) Tapa d salida al techo 24 pies (7,3 pies [7,3 m) Conducta recta de 12 pies (3,6 m) y diámetro de 6" 12 ples 36m) x {1} 12 pies {3,6 m) (15.
Instrucciones de instalación A EXTRACCIÓN SUPERIOR EXTERNA (conducto vertical) DESCRIPCIÓN GENERAL DE LA INSTALACIÓN Al. Monte de lo placa de instalación en la pared. A2. Preparación del gabinete superior. AZ. Ajuste del ventilador del microondas pare la I extracción superior externa. Ad. Verificación del funcionamiento del regulador de extraditaran. AS. instalación del horno microondas. Ab. Ajuste del adaptador de extracción. AZ. Acoplamiento del sistema de conductos.
Instrucciones de instalación MONTAJE DE INSTALACIÓN LA PLACA DE EN LA PARED B3 Fije la placa en la poder con los tornillos de fiador. Af menos un tornillo para madera debe ser utilizad pare fijo la placa a una viga de le pared. 1 Quite lus tuercas de mariposa de los tantalios, 2 | diserte los tornillos en ka placa de instalación, o través de tos " agujeres taladrados en fas partes de fo pared que ne son viga {ios paneles) y vuelve a insertar fus fueras de mariposa ester {19 mm) de caree tornillo.
3 ons ene ase 3 memo Jl NACHO PLANTING DE PARED POSTERIOR 0 PN: SP-24 Impress en China