Installation Instructions

P/N: A21568903
Installation Instructions for
Single-Door Freezer and Refrigerator Pairing Kit
We recommend an authorized service technician install the pairing kit.
Components
Contains:
Part Part number Qty.
A Heater Assembly: 12V 10W 14.4Ω , Aluminum foil
sandwich, PVC wire insulation, Acrylic adhesive, 5.5 mm x
2.5 mm barrel connector spliced in heater assembly
A21442902 1
B AC Power Cable: Ultra low profile 6ft NEMA 5-15P to C13
Angled Power Cord, 3 pin plug
A21545701 1
C Power Supply: 12V 60W AC/DC Adapter, 5.5mm x 2.5mm
x 10.5 mm plug connector
A21545401 1
D Double-sided Tape 316237303 2
E Clips 218990901 6
Recommended Tool: Gloves
IMPORTANT
Make sure there are two separate dedicated grounding-type duplex wall outlets for
the freezer and the refrigerator as specified in IMPORTANT SAFETY INFORMATION
in the Use & Care Manual.
Installation
Before cleaning your appliance, turn o power to your appliance by unplugging the power
cord from the electrical outlet. Wipe down both sides of the refrigerator and the freezer.

NOTE
Never use CHLORIDE to clean stainless steel. Clean stainless-steel front and handles
with non-abrasive soapy water and a dishcloth. Rinse with clean water and a soft
cloth. Wipe stubborn spots with an ammonia-soaked paper towel, and rinse. Use a
non-abrasive stainless-steel cleaner, such as Frigidaire ReadyClean™ Stainless Steel
Cleaner found on Frigidaire.com. Always follow the manufacturer’s instruction

NOTE
Always, clean, wipe and dry with the grain to prevent scratching. Wash the rest of
the cabinet with warm water and mild liquid detergent. Rinse well and wipe dry with
a clean soft cloth.
CAUTION
The cabinet is heavy. We recommend two people to lift or move the cabinet.
1. If you use the dual installation trim kit,
install the levelers on the units before
installing the heater (Fig. 1).
NOTE: Please refer to Single-Door
All Refrigerator and All Freezer Trim Kit
Installation Instruction.
Fig. 1
2. Peel o the paper backing from the
first heater.
3. Adhere the first heater to the upper
right side of the left-side unit (0.5in
from the top and 0.5" from the back
wall) so the harnesses come out
at the bottom.
NOTE: Make sure you adhere the heater
completely with no air pockets (Fig. 2A).
4. Peel o the paper backing from the
second heater.
5. Adhere the second heater to the
lower left side of the right-side unit
(0.5" from the bottom and 0.5" from
the back wall) so the harnesses come
out at the top.
NOTE: Make sure you adhere the heater
completely with no air pockets (Fig. 2B).
Avoid:
Both heaters on the Freezer
Both heaters on the Refrigerator
Both heaters on the top
Both heaters on the bottom
Both heaters in the center
6. Plug in the connector of the two
Heaters A into the Power Supply C
(Fig. 3).
NOTE: Confirm the power supply fits into
the cutout when placed on top of the unit.
on top of the unit, adhere it vertically
on the back wall of the unit and make
sure the connection of the 3-prong
connector to the power supply is
facing down (Fig. 5).
NOTE: You cannot feel the
heater temperature.
Fig. 5
9 Push the two units together.
10. Use the clips provided to hold the
excess power cords to the back of the
units such that all wires are away from
the floor (Fig. 6).
NOTE: Make sure the harnesses and cables
are cleared o the floor before the units are
pushed back in place. This will prevent any
damage to the wires.
NOTE: The location of clips shown is
an example.
11. Plug the power supply into the main
outlet before pushing the units into the
final position.
12. Units can now be installed.
Fig. 6
Final Checklist
 Wipe down units
 Heater 1 on top right side of the freezer
 Heater 2 on bottom left side of the refrigerator
 Heater plugged into power supply
 Power supply adhered to desired position
 Power cables held away from the floor with the help of clips
 Power supply plugged into the outlet and green LED on
A
B
C
D
E
Fig. 2
0.5"
0.5"
0.5"
A B
Also confirm the power supply reaches the
power outlet when placed on top of the
unit (Fig. 4A).
7. Apply the 2 strips of double-sided
tape to the power supply and adhere
the power supply on top of the unit
(Fig. 4B).
8. If the power supply cannot be placed
Fig. 4
A
B
Fig. 3
A
B
C
CAUTION
Use gloves for the next step.