Installation Instructions

9
INSTALLATION INSTRUCTIONS - FREESTANDING GAS RANGE
5.6 CAPACITY
Check ignition of oven burners.
The operation of oven igniters should be checked after
range and supply line connectors have been carefully
checked for leaks and range has been connected to
electricpower.Besureallpackingmaterialsandlitera-
ture are removed from oven.
The oven burner is equipped with an electric control sys-
tem as well as an electric oven burner igniter. If your model
is equipped with an upper oven burner, it will also have
an electric burner igniter. These control systems require
noadjustment.Whentheovenissettooperate,current
willowtotheigniter.Itwill“glow”similartoalightbulb.
Whentheigniterhasreachedatemperaturesufcientto
ignite gas, the electrically controlled oven valve will open
andamewillappearattheovenburner.Thereisatime
lapsefrom30to60secondsafterthethermostatisturned
ONbeforetheameappearsattheovenburner.Whenthe
oven reaches the set temperature, the glowing igniter will
cycleoff.Theburneramewillturnoffin20to30seconds
after the igniter turns off. To maintain any set oven
temperature, this cycle will continue as long as the oven
control is set to operate.
To check oven burner ignition:
a. Set oven to Bake at300ºF. See User’s Manual for
operating instructions.
b. Within60secondstheovenburnershouldignite.
Checkforproperame,andallowtheburnertocycle
once.ResetcontroltoOFF.
c. If your model is equipped with a waist-high broiler,
set oven to Broil. See User’s Manual for operating
instructions.
d. Within60secondsthebroilburnershouldignite.
Checkforproperame.Resetcontrolto OFF.
Check ignition of surface
burners.
Operationofelectricignitersshouldbecheckedafter
range and supply line connectors have been carefully
checked for leaks and range has been connected to elec-
tric power.
a. To check for proper ignition, push in and turn a
surface burner knob counterclockwise to the LITE
position. You will hear the igniter sparking.
b. The surface burner should ignite when gas is available
to the burner. Purge air from supply lines by leaving
knob in the LITE position until burner ignites. Each
burnershouldlightwithinfour(4)secondsinnormal
operation after air has been purged from supply lines.
c. Visuallycheckthatburnerhasaame.Oncethe
burner ignites, the control knob should be turned out of
the LITE position.
d. Try each surface control knob separately until all
surface burners have been checked. Each burner
location is equipped with a separate electrode.
Adjust LOW setting of surface
  burnervalves(linearow).
Test to verify if LOW setting should be adjusted:
a. Push in and turn control to LITE until burner ignites.
b. Push in and quickly turn knob to lowest position.
c. Ifburnergoesout,resetcontroltoOFF.
d. Removethesurfaceburnercontrolknob.
e. Insert a thin-bladed screwdriver into the hollow valve
stemandengagetheslottedscrewinside.Flamesize
can be increased or decreased with the turn of the
screw(seeFig.17andFig.18).
f. Adjustameuntilyoucanquicklyturnknobfrom
LITEtolowestpositionwithoutextinguishingthe
ame.Flameshouldbeassmallaspossiblewithout
extinguishing.
Note: Air mixture adjustments are not required on surface
burners.
Fig. 17
7
8
9
Burneramesize
5/8”
Cooktop
Fig. 18