Installation Instructions All Languages

ManualsBrandsFrigidaire ManualsAir ConditionersFrigidaire FRA103BT1

READ BEFORE INSTALLING UNIT

Compact Window Mounting (10~12K BTU)

Installation Instructions

Before installing, the top rail must be assembled on the unit.

Top Rail Hardware

Qty.

Ǝ6FUHZ

Top Rail

The top rail on your unit may already be installed. If not,

follow the steps below.

To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp

edges that may be exposed:

Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to

move and install the unit. To prevent injury or strain, use proper lifting and carrying techniques when moving unit.

Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit over

an extended period of time.

Handle air conditioner with care. Wear protective gloves whenever lifting or carrying the unit. AVOID the sharp

metal fins on front and rear coils.

Make sure air conditioner does not fall during installation.

3KLOLSV6FUHZGULYHU

Drill (If pilot holes are needed)

722/61(('('

ƎVFUHZV 7

sash lock

Mounting Hardware Qty.

lock frame

(For Vinyl-Clad windows)

'212786($1<6&5(:627+(57+$1

7+26(63(&,),('+(5(

NOTE:

6$9(&$5721DQGWKHVH,167$//$7,21

,16758&7,216IRUIXWXUHUHIHUHQFH7KHFDUWRQLV

the best way to store unit during winter, or when not

in use.

:+(5($33/,&$%/(7+(7235$,/0867%(

6(&85(/<)$67(1(':,7+$//)285

6&5(:6)256$)(7<5($6216

lock frame

(For Wooden windows)

A. Remove the air conditioner from the carton and place on a flat surface.

B. Remove top rail from the rear of the packaging material as shown in Fig. A

C. Align the hole in the top rail with those on the top of the unit as shown in Fig. B

'6HFXUHWKHWRSUDLOWRWKHXQLWZLWKWKHƎ6FUHZVDVVKRZQLQ)LJ&

Fig. B

2020215A0329

Fig. C

weather seals

Ǝ;Ǝ;Ǝ

window sash seal foam 1

Packaging

Top Rail

Fig. A

Summary of content (4 pages)

PAGE 1
Installation Instructions READ BEFORE INSTALLING UNIT Compact Window Mounting (10~12K BTU) To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may be exposed: Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and install the unit. To prevent injury or strain, use proper lifting and carrying techniques when moving unit.
PAGE 2
How to Install Installation LEFT + RIGHT FILLER PANEL ASSEMBLY NOTE: Top Rail and Side Panels at each side are offset to provide the proper pitch to the rear of (5/16”). This is necessary for proper condensed water utilization and drainage. If you are not using the Side Panels for any reason, this pitch to the rear must be maintained! Place unit on floor, a bench or a table. There is a Left and Right side Filler Panels - be sure to use the proper panel for each side.
PAGE 3
How to Install Installation Keep a firm grip on the air conditioner, carefully place the unit into the window opening so the bottom of the air conditioner frame is against the window sill (FIG. 6A & FIG. 6B). Carefully close the window behind the top rail of the unit. FIG. 6B FIG. 6A INSIDE OUTSIDE INSIDE OUTSIDE Wooden Windows Vinyl-Clad Windows Extend the side panels out against the window frame (FIG. 7A for wooden windows), (FIG. 7B for Vinyl-Clad windows). FIG. 7A FIG.
PAGE 4
Installation 7R VHFXUH ORZHU VDVK LQ SODFH DWWDFK ULJKW DQJOH VDVK ORFN ZLWK Ǝ PP VFUHZ DV VKRZQ ),* NOTE: It is difficult to lock the windows with the sash lock for Vinyl-Clad windows, so you can use lock by window itself. Cut foam window seal and insert it into the space between the upper and lower sashes (FIG. 11). FIG. 10 FIG. 11 FOAM SEAL After the completion of the installation, please check the machine’s lean as shown (FIG. 12A & FIG. 12B).