TDS

ManualsBrandsFrigidaire ManualsAppliances36 Inch Black Stainless Steel French Door Refrigerator

SERVICE DATA SHEET

A20430302

ICE & WATER - AUTOMATIC DEFROST

BOTTOM FREEZER - R600a

IMPORTANT: PLEASE RETURN THIS SHEET TO ITS ORIGINAL LOCATION.

This concludes the hardware tests. The following tests correspond to ﬁrmware versions. Before each ﬁrmware version is displayed “--”

will appear on screen followed by each 8-digit string representing ﬁrmware version. After the string has been displayed, “--” will ap-

pear again before automatically proceeded to the next 8-digit string. Press “+” to advance to the next string at any time

-- Software

Version

Runs automatically scrolling through all digits

Press “+” button to skip to next test

Displays digit sequence related to software load-

ed onto main power board; 8 digit sequence

Software version is able to

be recorded from display

-- Main Board

Firmware Version

Runs automatically scrolling through all digits

Press “+” button to skip to next test

Displays digit sequence related to firmware

loaded onto main power board; 8 digit sequence

Firmware version is able to

be recorded from display

-- Dispenser UI

Firmware Version

Runs automatically scrolling through all digits

Press “+” button to skip to next test

Displays digit sequence related to

ﬁrmware loaded onto Cobalt UI (on

exterior of unit); 8 digit sequence

Firmware version is able to

be recorded from display

-- Lifetime Press + button to advance to next digit Displays number of days the appliance has

been powered up, even not consecutively

Range is from 0-9999

Lifetime displays success-

fully on display

After Lifetime is displayed, last display is a 1-second counting up timer (0, 1, 2, 3…) this communicates that Service Mode has come to an end

To return to normal operation, press and hold “+” and “-” for 10 seconds or plug/unplug the appliance

DEFROST SPECIFICATIONS

Cabinet Size:

23’ CD/28' SD

Thermal Cutout Heater Defrost Thermistor Termination

Cutout Watts Ohms Cutout

FRZ 2 fuses, each fuse rated to

open @ 72 +0/-4 C

360 W

36.7 +/- 5% Ω

@ 25˚ C

50°F (10°C)

FFIM 2 fuses, each fuse rated to

open @ 72 +0/-4 C

60 W

220 +/-7.5% Ω

@ 25˚ C

64.4°F (18°C)

Electronic Timer - (ADC) Defrost 35 minutes every 8-96 hours of compressor run time

CONDENSER FAN MOTOR

Watts RPM Amps

3.1 1050 ± 50 130 CFM 39mA

(@115VAC/20°C)

Max Input Power (W) Speed

(R/Min)

Air Flow in Free Air

(@ 0 in H

ERROR CODES

Error Message Display

Interpretation

FZ Temp Disp. Area FF Temp Disp. Area

Er CE Communication Error UI to Main Board

dl SP Chute Flapper Error - Flapper not Closed

t1 FRZ Temp Sensor Opened/Shorted

t2 FRZ Defrost Sensor Open/Shorted

t3 FF Temp Sensor Opened/Shorted

t6 FF IM Tray Temp Sensor

t7 FF IM Defrost Sensor Opened/Shorted

t8 FRZ IM Temp Sensor

SPECIAL MODES

Mode

Display

Activate Deactivate

FZ FF Other

Manual Defrost d F

---

FZ + (∧) and FF + (∧) for 10 secs ---

Sabbath

Sb FZ — (∨) and FF

(∧) for 10 secs

FZ — (v) and FF + (

∧

) for 10 secs

Demo/Showroom

---

Demo Light On FZ

(∧) and FF — (∨) for 10 secs

FZ + (

∧

) and FF — (v) for 10 secs

System

Diagnostics

Refer to Systems

Diagnostics Table

(∧) and FZ — (∨) for 10 secs

FZ + (

∧

) and FZ — (v) for 10 secs

C Display

°F or °C FF

(∧) and FF — (∨) for 10 secs

FF + (

∧

) and FF — (v) for 10 secs

Sleep/Awake Mode Display o or always on CRUSH and LIGHT keys for 5 secs CRUSH

and

LIGHT

keys for 5 secs

FF and FZ IM Fill

Time Menu

Settings will appear on UI CUBE and CRUSH keys for 10 secs

After 10 secs of no activity

PERFORMANCE DATA NO LOAD & NO DOOR OPENINGS AT 37°/0° CONTROL SETTING

CD DISPENSER SD DISPENSER

Type A with Run /

Start Capacitor

55°F (13°C) Ambient 90°F (32°C) Ambient 55°F (13°C) Ambient 90°F (32°C) Ambient

Operating Time 65 to 70% 100% 55 to 60% 100%

Freezer Temp -8°F to 6°F (-22°C to -14°C)

Refrigerator Temp 33°F to 43°F (0° to 6°C)

Low Side

Pressure

-6.3 to -5.1 psig

(56 to 64 kPa)

-5.3 to -4.8 psig

(63 to 66 kPa)

-6.3 to -5.1 psig

(56 to 64 kPa)

-5.3 to -4.8 psig

(63 to 66 kPa)

High Side

Pressure

25 to 28 psig

(270 to 290 kPa)

57 to 61 psig

(490 to 520 kPa)

25 to 28 psig

(270 to 290 kPa)

57 to 61 psig

(490 to 520 kPa)

Wattage 35 to 40 50 to 60 50 to 55 60 to 70

Amps (running) 0.4 to 0.5 0.6 to 0.7 0.6 to 0.7 0.8 to 0.9

Base Voltage 115 vac (103 to 127 vac)

SYSTEM DIAGNOSTIC MODE

Activate:

Press and hold FZ + ˄ and FZ — ˅ buttons for 10 secs. Navigate through tests with FF + ˄/ FF — ˅ buttons. Automatically deactivates after 10 minutes of no activity.

Deactivate:

Display

code

Test Description

Activation/

Deactivation

Display Passing Result

---

First Screen

---

Turn on all LEDs on external dispenser UI

---

Second Screen Turn o all LEDs on external dispenser UI

2 Frz Defrost

Press CUBE to change

status of load

Heater on when display reads On, o when oF Defrost heater shows temp increase before 5 min have passed or reaches 45°c cutout

8 Main Water Valve Main valve is activated when On, stops when oF Valve is able to turn on and o

11 Cube/Crush Solenoid Solenoid activated when On, deactivated when oF Solenoid is able to turn on and o

12 Condenser Fan Fan on when display reads On, o when oF Fan motor is activated successfully

Water Valve Dispenser +

Main Valve

Water dispenses when On, stops when oF Water is dispensed successfully at dispenser

FF IM Water Valve +

Main Valve

Remove ice tray to collect water into a container to measure water ﬁll.

If collecting water into ice tray, perform test 50 ﬁrst to empty tray.

Water ﬂows in the tray when On; test is correspondent to ice tray water ﬁll setting.

Automatically goes to oF state once conﬁgured time has elapsed.

Water is dispensed at ice tray for conﬁgured time setting

72 FF IM Defrost Heater Heater on when display reads On, o when oF Defrost heater shows temp increase before 5 min have passed or reaches 45°c cutout

FRZ IM Water Valve +

Main Valve

Remove ice tray to collect water into a container to measure water ﬁll.

If collecting water into ice tray, perform test 50 ﬁrst to empty tray.

Water ﬂows in the tray when On; test is correspondent to ice tray water ﬁll setting.

Automatically goes to oF state once conﬁgured time has elapsed

Water is dispensed at ice tray for conﬁgured time setting

10 Auger Motor Auger activated when On, deactivated when oF Auger motor is successfully activated

13 FF Light Fresh Food lights come on when On; lights turn o when oF All FF lights turn on

FRZ Evaporator

Fan Motor

Fan runs at 3 speeds: Max speed On, Medium speed Mi, Stopped oF Locked rotor will show Lc

No PWM signal will show Ns when fan is stopped (oF)

No 12V signal or ground will show Np when fan is On or Mi

Fan will cycle through all 3 speeds and Lc or Ns or Np is not displayed

20 FRZ Light Freezer lights come on when On; lights turn o when oF FRZ light turns on

38 VCC Compressor Compressor is running at max speed when On, stopped when oF Compressor successfully turns on

47 Ice Chute Heater Chute heater is activated when On, deactivated when oF Heater turns on successfully and dierence in temperature is felt around dispenser ice chute

FF IM Evaporator

Fan Motor

Evap fan motor is activated when On, deactivated when oF FF IM evap fan turns on successfully

Flipper Mullion

DC Heater

Flipper mullion heater is activated when On, deactivated when oF Heater turns on successfully and dierence in temperature is felt along ﬂipper mullion

66 Dispenser Light Dispenser light comes on when On; light turns o when oF Dispenser pocket light turns on successfully

67 FF Fill Tube Heater FF ﬁll tube heater is activated when On, deactivated when oF

Fill tube heater is successfully turned on and o. Temperature increase is noted in ﬁll tube area

94 FRZ Fill Tube Heater FRZ ﬁll tube heater is activated when On, deactivated when oF

22 FF Damper Motor

FRZ Evap Fan will turn on at max speed. Damper is open when OP, closed when CL

Check for airﬂow when damper is fully open (OP) and no air ﬂow when fully closed (CL).

Screen will blink 1 during damper movement

Any FRZ evap fan motor errors will display alternatively of damper status during test

Damper opens and closes successfully and no air ﬂow is felt when damper is in closed (CL) position

Ice Chute/

Flapper Motor

When ﬂapper is closed, shows CL, when open OP Flapper door opens and closes successfully, Er does not show on display

FF IM Twist Tray

Harvest Test

Remove ice bucket in order to see rotation of tray.

Display will show "Go" when tray is in home position (horizontal). during rotation, screen will blink 1.

In case of failure at end of twisting operation, screen will show Er

Tray twists successfully and Er is not displayed at the end of the cycle

FF IM Bail Arm/

Ice Level Bucket

Remove ice bucket in order to see status of im bail arm.

Allow bail arm to drop freely, Em (empty) will show when tray returns home.

Hold bail arm up by hand, Fu (full) will show when tray returns home

In case of failure at end of twisting operation, will show Er. Screen will blink 1 during rotation.

Bail arm successfully completes test and Er is not displayed at the end of each cycle

FRZ IM Twist Tray

Harvest Test

Remove ice bucket in order to see rotation of tray.

Display will show Go when tray is in home position (horizontal).

During rotation, screen will blink 1.

In case of failure at end of twisting operation, screen will show Er

Tray twists successfully and Er is not displayed at the end of the cycle

FRZ IM Bail Arm/

Ice Level Bucket

Remove ice bucket in order to see status of im bail arm.

Allow bail arm to drop freely, Em (empty) will show when tray returns home.

Hold bail arm up by hand, Fu (full) will show when tray returns home

In case of failure at end of twisting operation, will show Er. Screen will blink 1 during rotation.

Bail arm successfully completes test and Er is not displayed at the end of each cycle

23 FF Door Switch Open/Close FF doors

Display shows CL when door is closed, OP when door is open

Display reads correctly when door is opened/closed24 FRZ Door Switch Open/Close FRZ door

27 FRZ IM Switch Toggle switch on/o Switch is closed when display reads On, open when oF

28 Dispenser Paddle Press paddle Display shows oF when paddle is pressed, On when paddle is released or not pressed Display shows oF when paddle is not pressed and On when paddle is pressed

29 FF Temp Sensor

Activates

automatically

Display will show compartment temperature in either C or F depending on mode