Installation Guide

ManualsBrandsFrigidaire ManualsKitchen Appliance PackageFrigidaire FRRERADWMW12094

INSTALLATION INSTRUCTIONS

FRONT CONTROL FREESTANDING ELECTRIC RANGE

INSTALLATION AND SERVICE MUST BE

PERFORMED BY A QUALIFIED INSTALLER.

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

IMPORTANT SAFETY INSTRUCTIONS

If the information in this manual is not followed

exactly, a re or electrical shock may result causing property

damage, personal injury or death.

Important Notes to the Installer:

• Read all instructions contained in these installation

instructions before installing range.

• Remove all packing material from the oven

compartments before connecting the gas & electrical

supply to the range.

• Observe all governing codes and ordinances.

• Be sure to leave these instructions with the

consumer.

Important Notes to the Consumer:

Keep these instructions with your owner’s guide for future

reference.

• As when using any appliance generating heat, there

are certain safety precautions you should follow.

These are listed in the Use & Care Guide, read it

carefully.

• Be sure your range is installed and grounded properly

by a qualied installer or service technician.

• Make sure the wall coverings around the range can

withstand the heat generated by the range.

• To eliminate the need to reach over the surface

elements, cabinet storage space above the elements

should be avoided.

Tip Over Hazard

Range

leveling leg

Anti-tip

bracket

• A child or adult can tip the

range and be killed.

• Verify the anti-tip device has

been installed to floor or wall.

• Ensure the anti-tip device is re-engaged to floor

or wall when the range is moved.

• Do not operate the range without the anti-tip

device in place and engaged.

• Failure to follow these instructions can result in

death or serious burns to children and adults.

To check if the anti-tip bracket is installed properly, use

both arms to grasp the rear edge of the range back.

Carefully attempt to tilt range forward. When properly

installed, the range should not tilt forward.

Refer to the anti-tip bracket installation instructions

supplied with your range for proper installation.

FOR YOUR SAFETY: Do not store or use gasoline

or other ammable vapors and liquids in the vicinity of this or

any other appliance.

United States

P/N 809127103 (1801) Rev. A

English – pages 1-8

Spanish - pages 9-16

Summary of content (16 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FRONT CONTROL FREESTANDING ELECTRIC RANGE INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER. IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE. READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. United States FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
PAGE 2
30” ELECTRIC FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS 1. Clearances and Dimensions a. Provide adequate clearances between the range and adjacent combustible surfaces. b. Location—Check location where the range will be installed. Check for proper electrical supply and the stability of floor. c. Dimensions that are shown must be used. Given dimensions provide minimum clearance. Contact surface must be solid and level.
PAGE 3
0” ELECTRIC FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS 2. Tools You Will Need installed, attach bracket to the floor. For floor mount, locate the bracket by placing back edge of the template where the rear of the range will be located. Mark the location of the screw holes, shown in template.
PAGE 4
30” ELECTRIC FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS C. Level and Position Range - Level range by adjusting the (4) leveling legs with a wrench. Note: Aminimum clearance of 1/8” (3 mm) is required between the bottom of the range and the leveling leg to allow room for the bracket. Use a spirit level to check your adjustments. Slide range back into position. Visually check that rear leveling leg is inserted into and fully secured by the Anti-Tip Bracket by removing lower panel or storage drawer.
PAGE 5
30” ELECTRIC FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS 4. Electrical Connection to the Range The Rear Access Cover must be removed (Fig 9). To remove, loosen center screw (one screw) and remove cover. The terminal block will then be accessible. 3 & 4 - Wire electrical wall Receptacle types & recommended mounting orientation on wall Required for new and remodeled installations Fig. 11 4-Wire Wall receptacle (14-50R) Allowed for existing installations 3 Wire Wall receptacle (10-50R) Fig.
PAGE 6
30” ELECTRIC FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS 4B. POWER CORD CONNECTIONS (3-Wire Connection Instructions For existing installations ONLY - Refer to Fig. 13). 4A. POWER CORD CONNECTIONS (4-Wire Connection Instructions - Refer to Fig.12) Before wiring the range review the suggested power source location drawing in Fig. 3. If connecting to a 4-Wire electrical system (new branch-circuit or mobile home requires 4-Wire connection): 1.
PAGE 7
30” ELECTRIC FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS 4C. 3 & 4-WIRE PERMANENT WIRE CONNECTIONS 3 - Wire Permanent Connection - follow Steps 1,2 & 5 below.4 - Wire Permanent Connection - follow Steps 1 thru 5 below. Before wiring the range, review the suggested power source location drawings in Fig. 3. If connecting to a 4-Wire electrical system (new branch-circuit or mobile home requires 4-Wire connection): 1.
PAGE 8
30” ELECTRIC FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS 6. Model and Serial Number Location Some models have a cool-air intake vent on the rear of the appliance. Do not block or obstruct this vent. The serial plate is located on the right-hand surface of the oven front frame at the storage or warmer drawer; or the lower panel area.
PAGE 9
INSTRUCCIONES DE INSTALACION LA ESTUFA ELECTRICA DE 30” LA INSTALACION Y EL SERVICIO DEBEN SER EFECTUADOS POR UN INSTALADOR CALIFICADO. IMPORTANTE: CONSERVE ESTAS INSTRUCCIONES PARA USO DEL INSPECTOR LOCAL DE ELECTRICIDAD. LEA Y CONSERVE ESTAS INSTRUCCIONES PARA REFERENCIA FUTURA. Estados Unidos PARA SU SEGURIDAD: No almacene ni use gasolina u otros vapores y líquidos inflamables cerca de este o cualquier otro electrodoméstico.
PAGE 10
INSTRUCCIONES DE INSTALACION PARA LA ESTUFA ELECTRICA DE 30” 1. Espacios y dimensiones a. Proporcione espacios adecuados entre la estufa y las superficies combustibles adyacentes. b. Ubicación—Examine el lugar en el cual va a ser instalada la estufa. Determine la existencia de suministro eléctrico adecuado y la estabilidad del piso. c. Se deben usar las medidas indicadas. Las dimensiones indicadas proporcionan espacio mínimo.
PAGE 11
INSTRUCCIONES DE INSTALACION PARA LA ESTUFA ELECTRICA DE 30” 2. Herramientas que va a necesitar pared. Si la parte trasera de la estufa está a más de 1-1/4” de la pared cuando ya está instalada, instale el soporte en el piso. Para el montaje en el piso, ubique el soporte colocando el borde trasero de la plantilla donde quedará ubicada la parte trasera de la estufa. Marque la ubicación de los agujeros de los tornillos mostrados en la plantilla.
PAGE 12
INSTRUCCIONES DE INSTALACION PARA LA ESTUFA ELECTRICA DE 30” Modelos que requieren Juego de Cordón para el Suministro de Energía C. Nivele y ubique la estufa - Nivele la estufa ajustando los cuatro (4) tornillos niveladores con una llave. Nota: Se debe dejar un espacio libre mínimo de 1/8” (3 mm) entre la parte inferior de la estufa y los tornillos niveladores a fin de dejar espacio para instalar el soporte. Use un nivel de burbuja de aire para verificar los ajustes. Deslice la estufa de nuevo a su lugar.
PAGE 13
INSTRUCCIONES DE INSTALACION PARA LA ESTUFA ELECTRICA DE 30” 4. Conexion electrica a la estufa. Se debe retirar la cubierta de acceso trasera (Fig. 9). Para retirar, afloje el tornillo central (un tornillo) y retire la cubierta de acceso. Así se puede tener acceso al tablero. de bornes.
PAGE 14
INSTRUCCIONES DE INSTALACION PARA LA ESTUFA ELECTRICA DE 30” 4B. CONEXIONES DEL CORDON DE ALIMENTACION (Instrucciones para conexión trifilar para instalaciones existentes SOLAMENTE - Consulte la Fig. 13) 4A. CONEXIONES DEL CORDON DE ALIMENTACION (Instrucciones para Conexión Tetrafilar - Consulte la Fig.12) Antes del cableado de la estufa, revise los dibujos de las ubicaciones sugeridas para la fuente de alimentación en la Fig. 3.
PAGE 15
INSTRUCCIONES DE INSTALACION PARA LA ESTUFA ELECTRICA DE 30” 4C. CONEXIONES DEL CABLEADO PERMANENTE TRIFILAR Y TETRAFILAR ENGANCHADO (Ver Fig. 7). Asegúrese de que el cordón de alimentación quede plegado en el resto del área abierta del piso detrás de la gaveta de almacenamiento o gaveta calentadora de la estufa. Asegúrese de verificar la nivelación de la estufa. NOTA: Los campos de la compresión de las conexiones de los cables no terminadas deben ser usadas utilizando un cable de 10 ga.
PAGE 16
INSTRUCCIONES DE INSTALACION PARA LA ESTUFA ELECTRICA DE 30” 6. Ubicación del modelo y número de serie Algunos modelos tienen un respiradero de admisión de aire frío en la parte posterior del aparato. No bloquee u obstruya esta ventilación. La placa de serie está ubicada en la superficie derecha del marco frontal del horno en el cajón de almacenamiento o calentador; o el área del panel inferior.